This study aimed to develop Janus-, cross-network-, and coaxial-structured piezoelectric-conductive polymer nanofibers through electrospinning to mimic the piezoelectricity of bone and facilitate the conduction of electrical signals in bone tissue repair. These nanofibers were constructed using the piezoelectric polymer polyvinylidene fluoride, and the conductive fillers reduced graphene oxide and polypyrrole. The influence of structural features on the electroactivity of the fibers was also explored. The morphology and components of the various structural samples were characterized using SEM, TEM, and FTIR. The electroactivity of the materials was assessed with a quasi-static d33 meter and the four-probe method. The results revealed that the piezoelectric-conductive phases were successfully integrated. The Janus-structured nanofibers demonstrated the best electroactivity, with a piezoelectric constant d33 of 24.5 pC/N and conductivity of 6.78 × 10-2 S/m. The tensile tests and MIP measurements showed that all samples had porosity levels exceeding 70%. The tensile strength of the Janus and cross-network structures exceeded that of the periosteum (3-4 MPa), with average pore sizes of 1194.36 and 2264.46 nm, respectively. These properties indicated good mechanical performance, allowing material support while preventing fibroblast invasion. The CCK-8 and ALP tests indicated that the Janus-structured samples were biocompatible and significantly promoted the proliferation of MC3T3-E1 cells.

This article focuses on the eco-friendly (green) synthesis of silver nanoparticles (AgNPs) and their incorporation into a polymer matrix. For AgNPs synthesis, Lavandula angustifolia (lavender) leaf extract was used as a reducing and stabilizing agent, and as a silver precursor, AgNO3 solution with different concentrations of silver (50, 100, 250, and 500 mg/L) was used. Prepared AgNPs colloids were characterized using UV-vis spectrophotometry, transmission electron microscopy (TEM), and X-ray diffraction (XRD). The spherical morphology of AgNPs with an average size of 20 nm was confirmed across all samples. Further, the antimicrobial properties of the AgNPs were evaluated using the disk diffusion method on algae (Chlorella kessleri) and the well diffusion method on bacteria (Staphylococcus chromogenes, Staphylococcus aureus, and Streptococcus uberis), along with root growth inhibition tests on white mustard (Sinapis alba). Polymer composite (PVA-AgNPs) was prepared by incorporation of AgNPs into the polymer matrix. Subsequently, non-woven textiles and thin foils were prepared. The distribution of AgNPs within the nanocomposites was observed by scanning electron microscopy (SEM). Antibacterial properties of PVA-AgNPs composites were analyzed on bacteria Streptococcus uberis. It was found that not only AgNPs showed good antimicrobial properties, but toxic properties were also transferred to the PVA-AgNPs nanocomposite.

Aim The aim of this study was to assess the physicochemical characterization and mineralization of nanofibrous scaffold incorporated with nanohydroxyapatite (nHA) and aspartic acid (Asp) for dental mineralization.  Methodology Three nanofibrous scaffolds were prepared, namely polycaprolactone (PCL), PCL with nHA, and PCL with nHA and Asp. Each scaffold was prepared separately by electrospinning. The physicochemical characterization of the surface of the nanofibrous scaffold was imaged using a scanning electron microscope (SEM), energy dispersive X-ray Analysis (EDX), X-ray diffraction (XRD), and Fourier-transform infrared spectroscopy (FTIR). In vitro mineralization studies were performed by immersing the sample in simulated body fluid (SBF) for 7, 14, and 21 days. The surface of the samples was observed under SEM with EDX. Results SEM analysis of PCL/nHA/Asp revealed that the nanofibers were bead-free, smooth, randomly oriented, and loaded with Asp. The EDX spectra of PCL/nHA/Asp composite nanofibrous scaffold revealed broad peaks and corresponded to the amorphous form, while the sharp peaks corresponded to the specific crystalline structure of nHA. FTIR analysis showed specific functional groups corresponding to PCL, nHA, and Asp. The scaffolds incorporated with Asp exhibited higher mineralization potential with an apatite-like crystal formation, which increased with an increase in the duration of immersion in SBF. Conclusion Physiochemical characterization demonstrated the incorporation of PCL/nHA/Asp in the electrospun nanofibrous scaffold. The mineralization analysis revealed that the presence of Asp enhanced the mineralization when compared with the PCL and PCL/nHA. PCL/nHA/Asp incorporated in scaffold can be a promising material for dental mineralization.

Novel wound dressings with therapeutic effects are being continually designed to improve the wound healing process. In this study, the structural, chemical, physical, and biological properties of an electrospun poly glycerol sebacate/poly lactide acid/platelet-rich plasma (PGS/PLA-PRP) nanofibers were evaluated to determine its impacts on in vitro wound healing. Results revealed desirable cell viability in the Fibroblast (L929) and macrophage (RAW-264.7) cell lines as well as human umbilical vein endothelial cells (HUVEC). Cell migration was evident in the scratch assay (L929 cell line) so that it promoted scratch contraction to accelerate in vitro wound healing. Moreover, addition of PRP to the fiber structure led to enhanced collagen deposition (~ 2 times) in comparison with PGS/PLA scaffolds. While by addition PRP to PGS/PLA fibers not only decreased the expression levels of pro-inflammatory cytokines (IL-6 and TNF-α) in RAW-264.7 cells but also led to significantly increased levels of cytokine (IL-10) and the growth factor (TGF-β), which are related to the anti-inflammatory phase (M2 phenotype). Finally, PGS/PLA-PRP was found to induce a significant level of angiogenesis by forming branching points, loops, and tubes. Based on the results obtained, the PGS/PLA-PRP dressing developed might be a promising evolution in skin tissue engineering ensuring improved wound healing and tissue regeneration.

The mechanical properties and microstructure of the cemented paste backfill (CPB) in dry-wet cycle environments are particularly critical in backfill mining. In this study, coal gangue, fly ash, cement, glass fiber, and nano-SiO2 were used to prepare CPB, and dry-wet cycle tests on CPB specimens with different curing ages were conducted. The compressive, tensile, and shear strength of CPB specimens with different curing ages under different dry-wet cycles were analyzed, and the microstructural damage of the specimens was observed by scanning electron microscopy (SEM). The results show that compared with the specimens without dry-wet cycles, the uniaxial compressive strength, tensile strength, and shear strength of the specimens with a curing age of 7 d after seven dry-wet cycles were the smallest, being reduced by 40.22%, 58.25%, and 66.8%, respectively. After seven dry-wet cycles, the compressive, tensile, and shear strength of the specimens with the curing age of 28 d decreased slightly. The SEM results show that with the increasing number of dry-wet cycles, the internal structure of the specimen becomes more and more loose and fragile, and the damage degree of the structural skeleton gradually increases, leading to the poor mechanical properties of CPB specimens. The number of cracks and pores on the specimen surface is relatively limited after a curing age of 28 d, while the occurrence of internal structural damage within the specimen remains insignificant. Therefore, the dry-wet cycle has an important influence on the both mechanical properties and microstructure of CPB. This study provides a reference for the treatment of coal-based solid waste and facilitates the understanding of the mechanical properties of backfill materials under dry-wet cycling conditions.

Polyvinylpyrrolidone (PVP) is a synthetic polymer that holds significance in various fields such as biomedical, medical, and electronics, due to its biocompatibility and exceptional dielectric properties. Electrospinning is the most commonly used tool to fabricate fibers because of its convenience and the wide choice of parameter optimization. Various parameters, including solution molarity, flow rate, voltage, needle gauge, and needle-to-collector distance, can be optimized to obtain the desired morphology of the fibers. Although PVP is commercially available in various molecular weights, PVP with a molecular weight of 130,000 g/mol is generally considered to be the easiest PVP to fabricate fibers with minimal challenges. However, the fiber diameter in this case is usually in the micron regime, which limits the utilization of PVP fibers in fields that require fiber diameters in the nano regime. Generally, PVP with a lower molecular weight, such as 10,000 g/mol and 55,000 g/mol, is known to present challenges in fiber preparation. In the current study, parameter optimization for PVP possessing molecular weights of 10,000 g/mol and 55,000 g/mol was carried out to obtain nanofibers. The electrospinning technique was utilized for fiber fabrication by optimizing the above-mentioned parameters. SEM analysis was performed to analyze the fiber morphology, and quantitative analysis was performed to correlate the effect of parameters on the fiber morphology. This research study will lead to various applications, such as drug encapsulation for sustained drug release and nanoparticles/nanotubes encapsulation for microwave absorption applications.

Bacterial corneal keratitis is a damage to the corneal tissue that if not treated, can cause various complications like severe vision loss or even blindness. Combination therapy with two antibiotics which are effective against Gram-positive and Gram-negative bacteria offers sufficient broad-spectrum antibiotic coverage for the treatment of keratitis. Nanofibers can be a potential carrier in dual drug delivery due to their structural characteristics, specific surface area and high porosity. In order to achieve a sustained delivery of amikacin (AMK) and vancomycin (VAN), the current study designed, assessed, and compared nanofibrous inserts utilizing polyvinyl alcohol (PVA) and polycaprolactone (PCL) as biocompatible polymers. Electrospinning method was utilized to prepare two different formulations, PVA-VAN/AMK and PCL/PVA-VAN/AMK, with 351.8 ± 53.59 nm and 383.85 ± 49 nm diameters, respectively. The nanofibers were simply inserted in the cul-de-sac as a noninvasive approach for in vivo studies. The data obtained from the physicochemical and mechanical properties studies confirmed the suitability of the formulations. Antimicrobial investigations showed the antibacterial properties of synthesized nanofibers against Staphylococcus aureus and Pseudomonas aeruginosa. Both in vitro and animal studies demonstrated sustained drug release of the prepared nanofibers for 120 h. Based on the in vivo findings, the prepared nanofibers\' AUC0-120 was found to be 20 to 31 times greater than the VAN and AMK solutions. Considering the results, the nanofibrous inserts can be utilized as an effective and safe system in drug delivery.

Innovative antibacterial therapies using nanomaterials, such as photothermal (PTT) and photodynamic (PDT) treatments, have been developed for treating wound infections. However, creating secure wound dressings with these therapies faces challenges. The primary focus of this study is to prepare an antibacterial nanofiber dressing that effectively incorporates stable loads of functional nanoparticles and demonstrates an efficient synergistic effect between PTT and PDT. Herein, a composite nanofiber mat was fabricated, integrating spherical molybdenum disulfide (MoS2) nanoparticles. MoS2 was deposited onto polylactic acid (PLA) nanofiber mats using vacuum filtration, which was further stabilized by sodium carboxymethyl cellulose (CMC) adhesion and glutaraldehyde (GA) cross-linking. The composite nanofibers demonstrated synergistic antibacterial effects under NIR light irradiation, and the underlying mechanism was explored. They induce bacterial membrane permeability, protein leakage, and intracellular reactive oxygen species (ROS) elevation, ultimately leading to >95 % antibacterial activity against Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli), which is higher than that of single thermotherapy (almost no antibacterial activity) or ROS therapy (about 80 %). In addition, the composite nanofiber mats exhibited promotion effects on infected wound healing in vivo. This study demonstrates the great prospects of composite nanofiber dressings in clinical treatment of bacterial-infected wounds.

BACKGROUND: Open reduction with internal fixation is the preferred treatment option for displaced facial bone fractures. The superior mechanical properties of metallic plates have made them the most widely used material in existing bone fixation systems. However, after the healing period, these permanent plates can cause various problems. Alternative bioresorbable materials are being investigated to reduce these potential problems. This study compares bone stability and viability by using graphene oxide (GO)-doped poly-lactic-co-glycolic acid (PLGA) nanofiber plates and titanium plates for rats with fractured mandibles.
METHODS: The study included 20 male Sprague-Dawley rats, divided into four groups: a control group (Group I), a mandibular fracture group with no additional application (Group II), a mandibular fracture group repaired with titanium plates (Group III), and a mandibular fracture group repaired with GO-PLGA plates (Group IV). After 2 months, all of the rats were euthanized. A bone compression test was performed to assess bone stability, and a histological examination was performed to evaluate bone healing.
RESULTS: The osteocyte lacunae, Haversian ducts, canaliculi, and vascular structures of Group IV were found to be higher. In the compression test, vertical compression was applied to the bone axis, and Group IV had a higher maximum load and maximum stretch. GO-PLGA plates were found to be statistically superior to titanium plates in terms of both bone stability and bone healing (p < 0.05).
CONCLUSIONS: The present study found that GO-PLGA plates are more effective than titanium plates for the treatment of mandibular corpus fractures.

Scaffold design is one of the three most essential parts of tissue engineering. Platelet-rich plasma (PRP) and platelet-rich fibrin (PRF) have been used in clinics and regenerative medicine for years. However, the temporal release of their growth factors limits their efficacy in tissue engineering. In the present study, we planned to synthesize nanofibrous scaffolds with the incorporation of PRP and PRF by electrospinning method to evaluate the effect of the release of PRP and PRF growth factors on osteogenic gene expression, calcification, proliferation, and cell adhesion of human bone marrow mesenchymal stem cell (h-BMSC) as they are part of scaffold structures. Therefore, we combined PRP/PRF, derived from the centrifugation of whole blood, with gelatin and Polycaprolactone (PCL) and produced nanofibrous electrospun PCL/Gel/PRP and PCL/Gel/PRF scaffolds. Three groups of scaffolds were fabricated, and h-BMSCs were seeded on them: (1) PCL/Gel; (2) PCL/Gel/PRP; (3) PCL/Gel/PRF. MTS assay was performed to assess cell proliferation and adhesion, and alizarin red staining confirmed the formation of bone minerals during the experiment. The result indicated that PCL/Gel did not have any better outcomes than the PRP and PRF group in any study variants after the first day of the experiment. PCL/gelatin/PRF was more successful regarding cell proliferation and adhesion. Although PCL/gelatin/PRP showed more promising results on the last day of the experiment in mineralization and osteogenic gene expression, except RUNX2, in which the difference with PCL/gelatin/PRF group was not significant.