BACKGROUND: The probability of a positive outcome of root canal therapy is substantially higher if the infection is eradicated successfully before the obturation of the root canal system. Irrigation is an essential aspect of root canal debridement, as it enables more thorough cleaning than is possible with root canal instrumentation alone. To overcome the side effects of chemical irrigants, there has been a search for herbal medicines as substitutes.
OBJECTIVE: The aim of the present study was to explore the antimicrobial efficacy of white tea-mediated silver nanoparticles (AgNPs) formulated as an intracanal irrigant against Enterococcus faecalis, and to compare it with the efficacy of chlorhexidine and sodium hypochlorite irrigants.
METHODS: The experimental groups were as follows: group I - white tea-mediated AgNPs; group II - 2% chlorhexidine; and group III - 2.5% sodium hypochlorite. The characterization of AgNPs was performed using ultraviolet-visible (UV-Vis) spectroscopy and transmission electron microscopy (TEM) analysis. Enterococcus faecalis was inoculated onto Mueller-Hinton agar plates. The disks impregnated with irrigants were placed on the inoculated plates and incubated aerobically at 37°C for 24 h. Then, the growth inhibition zones were measured. Statistical analysis was performed using the one-way analysis of variance (ANOVA) and the post hoc tests.
RESULTS: A concentration of 50 μL of white tea-mediated AgNPs exhibited the greatest zone of inhibition (32 ±2 mm), followed by 2% chlorhexidine (25 ±1 mm) and 2.5% sodium hypochlorite (23 ±3 mm).
CONCLUSIONS: White tea-mediated AgNPs showed promising results in the elimination of E. faecalis, being superior to chlorhexidine and sodium hypochlorite irrigants.

OBJECTIVE: This study aimed to develop a systematic interdental brush set with size distribution based on the passage hole diameter (PHD), addressing existing gaps in size selection criteria for effective interdental cleaning.
METHODS: In the first step, an interdental brush set that ascends stepwise according to the PHD value was envisioned. The study was divided into three phases: (i) in-vitro determination of PHD values of a currently existing assortment on the market by 13 calibrated dental professionals, (ii) in-vitro assessment of forces during insertion, and (iii) creation and evaluation of new prototypes for missing or non-matching PHD sizes. Intra- and inter-rater reliability, assessed with the intraclass correlation coefficient (ICC), as well as insertion forces and PHD sizes at all stages were reported.
RESULTS: In the existing range, three interdental brushes fitting the desired PHD sizes were initially identified. Mean insertion forces between 0.3 and 1.7 N were documented based on raters\' PHD choices. Two additional rounds of measurements with prototypes adapted in diameter and shape were necessary, particularly for PHD values of 1.4, 2.3 and 2.6. High intra- and inter-rater reliability was observed throughout the study (ICC > 0.95), ensuring consistent evaluations. After three rounds of assessments, a prototype was successfully identified for each targeted PHD value in the systematised set, showcasing reliable sizing and insertion forces.
CONCLUSIONS: Using a structured approach, a comprehensive interdental brush set was developed with reliable PHD sizing and moderate insertion forces. The verification of size reliability through measurements by dentists represents a novelty in development and underlines the importance of accurate brush size selection for optimal biofilm control. Whether a systematic set based on the PHD value offers added value for clinical practice, and at what intervals, must be demonstrated in further studies.

This in vitro study aimed to investigate potential changes in the color and roughness of dental enamel resulting from the use of different toothpaste formulations during bleaching with violet LED light (405 nm). Sixty specimens of bovine incisors, each measuring 6 × 6 × 3 mm, were segregated into six distinct experimental groups based on their respective treatments (n = 10): C + VL: Brushing with Colgate® Total 12 + bleaching with violet LED; LB + VL: Brushing with Colgate® Luminous White Brilliant + bleaching with violet LED; LI + VL: Brushing with Colgate® Luminous White Instant + violet LED bleaching; C: Brushing with Colgate® Total 12; LB: Brushing with Colgate® Luminous White Brilliant; LI: Brushing with Colgate® Luminous White Instant. The examined variables included alterations in color (∆L*, ∆a*, ∆b*, ∆Eab, and ∆E00), surface roughness (Ra), and scanning electron microscopy observations. No statistically significant distinctions emerged in total color variations (∆E00 and ∆E) among the groups under scrutiny. Notably, the groups that employed Colgate® Luminous White Instant displayed elevated roughness values, irrespective of their association with violet LED, as corroborated by scanning electron microscopy examinations. It can be concluded that whitening toothpastes associated to violet LED do not influence the color change of dental enamel in fifteen days of treatment. Toothpastes with a higher number of abrasive particles showed greater changes in enamel roughness, regardless of the use of violet LED.

OBJECTIVE: To analyze the differences in cusp height on radiographs, establishing proportional relationships between cusp and alveolar bone crest (ABC) measurements. The goal of this study was to develop a correction coefficient by considering this proportion.
METHODS: Twenty-one artificial teeth, molars and premolars, and bovine ribs were used. Interproximal radiographs were taken with the aid of a positioner. The vertical angles used were: 0°, + 5°, and + 10°, and processed using three spatial resolutions measured in line pairs per mm (lp/mm): 20, 25 and 40. The Perio filter was applied to each image, in addition to the original one. Combinations of angle, resolution, and filter were made. Eighteen images were analyzed by three specialists, resulting in 252 measurements for each evaluator, totaling 756 measurements.
RESULTS: The overall variability of the measurements can be explained mainly by the variation in tooth anatomy. The 0° 25 lp/mm Perio filter method was the closest one to the actual clinical scenario for both cusps and ABC. The correction factor managed to explain 71.45% of the errors.
CONCLUSIONS: The variation in vertical angulation interferes with cusp and ABC measurements, and the angulation at 0º and spatial resolution of 25 lp/mm showed better results. The use of correction coefficients allowed approaching actual measurement values.
CONCLUSIONS: More accurate ABC height measurements are essential even in radiographic exams that do not meet the standard of excellence because the need to repeat radiographic exams is then eliminated.

OBJECTIVE: this study aimed to digitally compare wear behavior and retention between PEEK and nylon retentive inserts used in locator-retained, mandibular implant overdentures when attachment design and size were standardized.
METHODS: A total of sixty-four inserts (32 PEEK and 32 nylon inserts); were picked-up in implant overdentures. Overdentures of both groups were submerged in artificial saliva and mounted to chewing simulator. After 480,000 chewing cycles (equivalent to 2 years of clinical use) all inserts were scanned by scanning electron microscope (SEM), then all acquired images were digitally analyzed by software to detect and compare quantitative and qualitative changes of inserts in both groups. On the other hand, retention of both groups was measured by universal testing machine and the collected data was statistically analyzed using one-way Analysis of Variance (ANOVA) test with significance level set at P ≤ 0.05.
RESULTS: PEEK inserts showed significantly higher mean retentive values compared to the nylon inserts in the control group. Also, PEEK retentive inserts exhibited statistically lower mean wear values than the control group P ≥ 0.000. Qualitative investigation revealed significant and more pronounced changes in the surface roughness of nylon inserts compared to PEEK ones.
CONCLUSIONS: Regarding retention, wear behavior and dimension stability, PEEK can be recommended as retentive insert material in cases of locator-retained mandibular implant overdentures.
CONCLUSIONS: PEEK inserts offer enhanced retention, reduced wear, and greater dimensional stability over two years time interval. Clinically, this reduces prosthodontic maintenance and adjustments, improving patient satisfaction and long-term prosthetic success.

In this in vitro study, the use of a 445 nm diode laser was investigated for the decontamination of titanium dental implants. Different irradiation protocols and the effect of repetitive laser irradiation on temperature increase and decontamination efficacy were evaluated on titanium implant models. An automated setup was developed to realize a scanning procedure for a full surface irradiation to recapitulate a clinical treatment. Three irradiation parameter sets A (continuous wave, power 0.8 W, duty cycle (DC) 100%, and 5 s), B (pulsed mode, DC 50%, power 1.0 W, and 10 s), and C (pulsed mode, DC 10%, power 3.0 W, and 20 s) were used to treat the rods for up to ten consecutive scans. The resulting temperature increase was measured by a thermal imaging camera and the decontamination efficacy of the procedures was evaluated against Escherichia coli and Staphylococcus aureus, and correlated with the applied laser fluence. An implant\'s temperature increase of 10 °C was set as the limit accepted in literature to avoid thermal damage to the surrounding tissue in vivo. Repeated irradiation of the specimens resulted in a steady increase in temperature. Parameter sets A and B caused a temperature increase of 11.27 ± 0.81 °C and 9.90 ± 0.37 °C after five consecutive laser scans, respectively, while parameter set C resulted in a temperature increase of only 8.20 ± 0.53 °C after ten surface scans. The microbiological study showed that all irradiation parameter sets achieved a complete bacterial reduction (99.9999% or 6-log10) after ten consecutive scans, however only parameter set C did not exceed the temperature threshold. A 445 nm diode laser can be used to decontaminate dental titanium rods, and repeated laser irradiation of the contaminated areas increases the antimicrobial effect of the treatment; however, the correct choice of parameters is needed to provide adequate laser fluence while preventing an implant\'s temperature increase that could cause damage to the surrounding tissue.

BACKGROUND: The temperature changes, chemical agents, and brushing activity that resin composite restorations are exposed to in the oral environment can cause changes in surface roughness. In this study, the aim was to investigate in vitro the clinical one-year surface roughness changes of different types of composites (flowable or conventional) from the same companies by subjecting them to immersion in solutions, brushing, and thermal cycling procedures to simulate intraoral conditions.
METHODS: Four different resin composite brands were included in the study using both their conventional (Charisma Smart, 3M Filtek Ultimate Universal, Omnichroma, Beautifil II) and flowable resin composites (Charisma Flow, 3M Filtek Ultimate Flowable, Omnichroma Flow, Beautifil Flow Plus F00), giving 4 groups with 2 types of resin composite in each. 40 samples were prepared for each group/resin type, for a total of 320 samples. After initial surface roughness measurements by a mechanical profilometer, the samples were divided into 4 subgroups (n = 10) and immersed in solutions (distilled water, tea, coffee, or wine) for 12 days. The samples were then subjected to 10,000 cycles of brushing simulation and 10,000 cycles of thermal aging. Surface roughness measurements were repeated after the procedures. For statistical analysis, the 3-way analysis of variance and the Tukey test were used (p < 0.05).
RESULTS: It was concluded that composite groups and types had an effect on surface roughness at time t0 (p < 0.001). At time t1, the highest surface roughness value was obtained in the Beautifil-conventional interaction. When the surface roughness values between time t0 and t1 were compared, an increase was observed in the Beautifil II and Beautifil Flow Plus F00, while a decrease was observed in the other composite groups.
CONCLUSIONS: Composite groups, types, and solutions had an effect on the surface roughness of resin composites. After aging procedures, it was concluded that the Beautifil group could not maintain the surface structure as it exceeded the threshold value of 0.2 μm for bacterial adhesion.

BACKGROUND: The purpose of this pilot in-vitro study was to assess the effect of sterilization on the intra-implant axis, inter-implant axis, intra-implant distance and inter-implant distance of three implants in a straight line by using laboratory scanner (LBS) versus intra-oral scanner (IOS) with intra-oral scan bodies (ISB).
METHODS: A printed 3D model with three internal hex analogs in the positions 15#,16#,17# was used. Zirkonzhan (ZZ) intra-oral scan body (ISB), two-piece titanium was used. The ZZ ISBs were scanned by 7 Series dental wings (LBS) and 30 times by Primescan (IOS) pre sterilization and 30 times post sterilization. For each scan (pre and post) stereolithography (STL) file was created and a comparison between all the scans pre sterilization and post sterilization were superimposed on the laboratory scan by using a 3D analyzing software. A Kolmogorov-Smirnov test performed followed by Wilcoxon Signed Ranks tests. (p < 0.05) Results: Post sterilization of the ZZ ISB, the mean errors were significantly increased for the inter-implant distances (p < 0.0005), intra-implant distances 1,2,3 (p < 0.0005), intra-implant axis 1,3 (p < 0.0005) and inter-implant axes 13,23 (p < 0.05). In contrast, the mean errors for intra-implant axis 2 (p < 0.0005) and inter-implant axis 12 (p < 0.0005) were significantly reduced.
CONCLUSIONS: ZZ ISB showed changes in all four parameters after sterilization. The middle ISB had the largest changes in mean error regarding all four parameters. Sterilization process may affect the three-dimensional (3D) structure of the ZZ ISB after three cycles. There is a lack in the literature in this field and there is a need for further studies to explore the effect of sterilization (multiple cycles) on different ISBs and for creating an approved guidelines regarding the amount of sterilization for each ISB in the industry.

To assess and compare the anti-microbial efficacy of 445 nm and 970 nm diode laser on mixed species biofilm of Aggregatibacter actinomycetemcomitans [A.a] and Porphyromonas gingivalis [P.g] cultured on machined pure titanium discs. A total of 65 machined pure titanium discs with no surface modifications with a 10-mm diameter and a 2-mm height were sterilized by autoclaving at 121 °C for 15 min and incubated with the commercially available bacterial strains ATCC(American Type Culture Collection- P.g 33277 and A.a 29522)mixture of Aggregatibacter actinomycetemcomitans(A.a) and Porphyromonas gingivalis(P.g).After a 2-week incubation period with the mixture of bacteria to develop a mixed species biofilm, the discs were divided into three groups: (1) no treatment (control), (2) 445 nm laser (test), (3) 970 nm laser (test). For each laser wavelength (445 and 970 nm), the discs were exposed to 1.0 W and 2.0 W in continuous wave mode for the times points of 15, 30, and 60 s. The antimicrobial efficacy was assessed by qPCR. A significant reduction in the levels of both species of bacteria was observed between control and the laser intervention groups. A higher efficacy for the 445 nm diode laser against Porphyromonas gingivalis and a similar efficacy against Aggregatibacter actinomycetemcomitans was observed as compared to the 970 nm group. 445 nm wavelength represents a potential and effective laser wavelength which can be used for the management of peri-implant infection. The present study findings also need to be further validated through clinical interventional trials.

Glass ionomer cements (GICs) are the common materials employed in pediatric dentistry because of their specific applications in class I restorations and atraumatic restoration treatments (ART) of deciduous teeth in populations at high risk of caries. Studies show a limited clinical durability of these materials. Attempts have thus been made to incorporate nanoparticles (NPs) into the glass ionomer for improving resistance and make it like the tooth structure. An in vitro experimental study was conducted using the required samples dimensions and prepared based on the test being carried out on the three groups with or without the modification of light-cured glass ionomer. Samples were grouped as follows: control group (G1_C), 2% silver phosphate/hydroxyapatite NPs group (G2_SPH), and 2% titanium dioxide NPs group (G3_TiO2). The physical tests regarding flexural strength (n = 10 per group), solubility (n = 10 per group), and radiopacity (n = 3 per group) were performed. The data were analyzed by Shapiro Wilks test, and one-way analysis of variance (one-way ANOVA), and multiple comparisons by post hoc Tukey\'s test. The p-value of < 0.05 was considered significant. No statistically significant difference was observed between the control group (G1_C) and (G2_SPH) (p = 0.704) in the flexural strength test, however differences were found between G2_SPH and G3_TiO2 groups, ANOVA (p = 0.006); post hoc Tukey\'s test (p = 0.014). Pertaining to the solubility, G2_SPH obtained the lowest among the three groups, ANOVA (p = 0.010); post hoc Tukey\'s test (p = 0.009). The three study groups obtained an adequate radiopacity of >1 mm Al, respectively. The resin-modified glass ionomer cement (RMGIC) was further modified with 2% silver phosphate/hydroxyapatite NPs to improve the physical properties such as enhancing the solubility and sorption without compromising the flexural strength and radiopacity behavior of modified RMGIC. The incorporation of 2% titanium dioxide NPs did not improve the properties studied.