In recent years, self-healing polymers have emerged as a topic of considerable interest owing to their capability to partially restore material properties and thereby extend the product\'s lifespan. The main purpose of this study is to investigate the nanoindentation response in terms of hardness, reduced modulus, contact depth, and coefficient of friction of a self-healing resin developed for use in aeronautical and aerospace contexts. To achieve this, the bifunctional epoxy precursor underwent tailored functionalization to improve its toughness, facilitating effective compatibilization with a rubber phase dispersed within the host epoxy resin. This approach aimed to highlight the significant impact of the quantity and distribution of rubber domains within the resin on enhancing its mechanical properties. The main results are that pure resin (EP sample) exhibits a higher hardness (about 36.7% more) and reduced modulus (about 7% more), consequently leading to a lower contact depth and coefficient of friction (11.4% less) compared to other formulations that, conversely, are well-suited for preserving damage from mechanical stresses due to their capabilities in absorbing mechanical energy. Furthermore, finite element method (FEM) simulations of the nanoindentation process were conducted. The numerical results were meticulously compared with experimental data, demonstrating good agreement. The simulation study confirms that the EP sample with higher hardness and reduced modulus shows less penetration depth under the same applied load with respect to the other analyzed samples. Values of 877 nm (close to the experimental result of 876.1 nm) and 1010 nm (close to the experimental result of 1008.8 nm) were calculated for EP and the toughened self-healing sample (EP-R-160-T), respectively. The numerical results of the hardness provide a value of 0.42 GPa and 0.32 GPa for EP and EP-R-160-T, respectively, which match the experimental data of 0.41 GPa and 0.30 GPa. This validation of the FEM model underscores its efficacy in predicting the mechanical behavior of nanocomposite materials under nanoindentation. The proposed investigation aims to contribute knowledge and optimization tips about self-healing resins.

Developing extracellular matrix-derived hydrogel with a fast self-healing capacity to provide a sustainable moist environment able to accelerate wound healing is highly desired for full-thickness skin wound repair. In this study, a fast self-healing hyaluronic acid hydrogel with a dual dynamic network was constructed through a primary reversible acylhydrazone bond formed between aldehyde-modified hyaluronic acid, 3,3\'-dithiobis (propionyl hydrazide) (DTP), and secondary dynamic ionic interactions between κ-carrageenan (KC) and K+. Because of the presence of various dynamic covalent bonds such as the acylhydrazone bond, disulfide bond, and noncovalent bonds including hydrogen bonding and ionic interactions, as well as the notable thermoreversible nature of KC, the resultant hydrogel could be self-healed rapidly within 30 min under physiological temperature with a self-healing efficiency of 100%, which was significantly better than other hyaluronic acid hydrogels, as reported previously. Besides, the hydrogel displayed excellent cytocompatibility. According to this study, the hydrogel was administered into the wounds and achieved a superior performance of promoting full-thickness skin wound healing by increasing granulation tissue formation, deposition of collagen as well as the acceleration of re-epithelialization and neovascularization, compared to commercial products, e.g., gauze and 3 M hydrocolloid. We also anticipate that this strategy of double-dynamic network cross-linking can be adopted to fabricate self-healing materials for multiple applications.

Novel reprocessable thermosetting adhesives (RTAs), which combine high adhesive strength, reusability, disassembly, and recyclability features, have attracted increasing attention. However, developing RTAs with a rapidly adhesive rate while ensuring high adhesive strength and self-healing ability is still a significant challenge. Here, we prepared a novel vitrimer called DAx-DTSAy, which can be used as an RTA. First, by adjusting the ratio of rigid and flexible segments, maximum tensile strength reached 35.92 MPa. Second, the combined effect of dynamic hydroxyl ester bonds and dynamic disulfide bonds resulted in a rapid stress relaxation behavior, with a complete relaxation time 13.6 times shorter than a vitrimer only cross-linked with hydroxy ester bonds. This feature endowed its good self-healing and reprocessing capabilities. After self-healing at 180 °C, the maximum healing rate of mechanical properties was 91.8%. After three reprocesses, the maximum recovery rate of tensile strength was 120.2%. Furthermore, the combination of rigid and flexible segments and the synergistic effect of dual dynamic covalent bonds made DAx-DTSAy capable of use as a high-performance RTA. The lap shear strength of a DAx-DTSAy film on stainless steel reached 18.18 MPa after 15 min, with a recovery rate of 91.9% after 5 rebonding cycles. Additionally, DAx-DTSAy can be disassembled in chemical agents and exhibited better insulation properties compared to traditional epoxy resins. DAx-DTSAy can be employed as a novel high-performance adhesive in applications such as electronic devices and transportation, contributing to the development of thermosetting adhesives toward recyclability and sustainability.

Conductive hydrogels (CHs) are emerging materials for next generation sensing systems in flexible electronics. However, the fabrication of competent CHs with excellent stretchability, adhesion, self-healing, photothermal conversion, multisensing, and environmental stability remains a huge challenge. Herein, a nanocomposite organohydrogel with the above features is constructed by in situ copolymerization of zwitterionic monomer and acrylamide in the existence of carboxylic cellulose nanofiber-carrying reduced graphene oxide (rGO) plus a solvent displacement strategy. The synergy of abundant dipole-dipole interactions and intermolecular hydrogen bonds enables the organohydrogel to exhibit high stretchability, strong adhesion, and good self-healing. The presence of glycerol weakens the formation of hydrogen bonds between water molecules, endowing the organohydrogel with excellent environmental stability (-40 to 60 °C) to adapt to different application scenarios. Importantly, the multimodal organohydrogel presents excellent sensing behavior, including a high gauge factor of 16.3 at strains of 400-1440% and a reliable thermal coefficient of resistance (-4.2 °C-1) over a wide temperature widow (-40 to 60 °C). Moreover, the organohydrogel displays a highly efficient and reliable photothermal conversion ability due to the favorable optical absorbing behavior of rGO. Notably, the organohydrogel can detect accurate human activities at ambient temperature, demonstrating potential applications in flexible intelligent electronics.

Gel electrolytes have attracted extensive attention in flexible batteries. However, the traditional hydrogel electrolyte is not enough to solve the fundamental problems of zinc anodes, such as dendrite growth, side reactions, and freezing failure at temperatures below zero, which seriously restricts the development of zinc-ion batteries. As a flexible energy storage device, the zinc-ion battery inevitably undergoes multiple stretches, bends, folds, or twists in daily use. Here, a self-healing and stretchable eutectogel, designated as deep eutectic solvent-acrylamide eutectic gel (DA-ETG), was developed as a solid-state electrolyte for zinc-ion batteries. This gel was prepared by immobilizing a high-concentration ZnCl2 deep eutectic solvent (DES) into a polyacrylamide matrix through in situ polymerization under ultraviolet light. The eutectogel electrolyte showed exceptional mechanical properties with a maximum fracture strength of 0.6 MPa and a high ionic conductivity of 6.4 × 10-4 S cm-1. The in situ polymerization of the DA-ETG electrolyte in the assembly of a full solid-state zinc-ion battery increased the electrode-electrolyte interface area contact, reduced the ion transport distance between the electrode and electrolyte, minimized the internal resistance, and enhanced the battery\'s long-term cycling stability. Using the DA-ETG electrolyte, a remarkably high capacity of 580 mAh g-1 at 0.1 A g-1 was achieved by the zinc-ion battery, and a considerable capacity of 234 mAh g-1 was maintained even at 5 A g-1, showing exceptional rate performance. After 2000 cycles at 2 A g-1, the cell with the eutectogel retained a capacity of 85% with a cycling efficiency close to 98%, which demonstrated excellent cycling stability. The self-healing function enabled the prepared soft battery to be reused multiple times, with full contact between the electrode and electrolyte interface, and without device failures.

Eutectogels have garnered considerable attention for the development of wearable devices, owing to their inherent mechanical elasticity, ionic conductivity, affordability, and environmental compatibility. However, the low conductivity of existing eutectogels has impeded their progression in electronic applications. Here, we report a zwitterionic eutectogel with an impressive ionic conductivity of up to 15.7 mS cm-1. The incorporation of zwitterionic groups into the eutectogel creates ample mobile charges by dissociating the cation and anion of solvents, thereby yielding exceptional ionic conductivity. Moreover, the abundant electrostatic and hydrogen bonding interactions within the eutectogel endow it with prominent self-healing and adhesive properties. By integrating the eutectogel with a roughly patterned polydimethylsiloxane film, we have successfully constructed a triboelectric nanogenerator (TENG) with a maximum output power density of 112 mW m-2. This TENG is capable of generating stable electrical signals even in extreme temperature conditions ranging from -80 to 100 °C and effectively powering electronic devices. Furthermore, the assembled TENG displays high sensitivity as a self-powered sensor, enabling real-time and precise monitoring of signals derived from human motions. This study establishes a promising approach for the development of sustainable and multifunctional flexible electronics that are resilient in extreme environments.

In situ-forming biocompatible hydrogels have great potential in various medical applications. Here, we introduce a pH-responsive, self-healable, and biocompatible hydrogel for cell scaffolds and the development of a tumor spheroid phantom for magnetic resonance imaging. The hydrogel (pMAD) was synthesized via amino-yne click chemistry between poly(2-methacryloyloxyethyl phosphorylcholine-co-2-aminoethylmethacrylamide) and dialkyne polyethylene glycol. Rheology analysis, compressive mechanical testing, and gravimetric analysis were employed to investigate the gelation time, mechanical properties, equilibrium swelling, and degradability of pMAD hydrogels. The reversible enamine and imine bond mechanisms leading to the sol-to-gel transition in acidic conditions (pH ≤ 5) were observed. The pMAD hydrogel demonstrated potential as a cellular scaffold, exhibiting high viability and NIH-3T3 fibroblast cell encapsulation under mild conditions (37 °C, pH 7.4). Additionally, the pMAD hydrogel also demonstrated the capability for in vitro magnetic resonance imaging of glioblastoma tumor spheroids based on the chemical exchange saturation transfer effect. Given its advantages, the pMAD hydrogel emerges as a promising material for diverse biomedical applications, including cell carriers, bioimaging, and therapeutic agent delivery.

Surgical operations are the preferred treatment for gastric perforation (GP) but incur postoperative complications such as gastrointestinal adhesions and bacterial infections, leading to inefficient wound healing and serious complications that may even threaten the life of the patient. Developing hydrogel dressings capable of adapting to the gastric environment (acid) and decreasing visceral adhesions and bacterial infections after GP treatment is crucial. In this article, we developed an injectable, self-healing hydrogel using cation-π interactions between protonated amines and aromatic rings under acidic conditions and explored it for GP repair. The hydrogels demonstrate exceptional self-healing capabilities under acidic conditions and can be effectively tailored for the gastric environment. In addition, the hydrogel demonstrated significant efficacy in preventing gastrointestinal adhesion, reducing inflammation, promoting angiogenesis, and effectively facilitating wound healing in a rat GP model. This novel hydrogel demonstrates adaptability to the gastric environment, rendering it highly promising for potential applications in gastric trauma healing.

Metal halide materials have recently drawn increasing research interest for their excellent opto-electronic properties and structural diversity, but their resulting rigid structures render them brittle and poor formability during manufacturing. Here we demonstrate a thermoplastic luminant hybrid lead halide solid by integrating lead bromide complex into tri-n-octylphosphine oxide (TOPO) matrix. The construction of the hybrid materials can be achieved by a simple dissolution process, in which TOPO molecules act as the solvents and ligands to yield the monodispersed clusters. The combination of these functional units enables the near-room-temperature melt-processing of the materials into targeted geometry by simple molding or printing techniques, which offer possibilities for fluorescent writing inks with outstanding self-healing capacity to physical damage. The intermarriage between metal halide clusters with functional molecules expands the range of practical applications for hybrid metal halide materials.