UNASSIGNED: To evaluate the efficacy and safety of Holmium: Yttrium-Aluminum-Garnet (Ho:YAG) laser in bladder lithotripsy using high-power settings > 100 W.
UNASSIGNED: A combined experimental and clinical study was conducted. The Quanta Cyber: Ho 150 with a 550 μm Quanta optical fiber was utilized in all set-ups. Ablation rates for soft and hard artificial stones were tested in vitro using 100 W and 20 W power settings. In the experiment, a porcine bladder was used. The optical fiber was inserted through a rigid cystoscope, whilst a K-type thermocouple was inserted in the bladder dome. The tested high-power settings were 152 W, 120 W and 105 W. In every trial, the lasing time was over 60 s. In the clinical study, 35 patients underwent transurethral high-power bladder lithotripsy. Laser settings were set between 100 W and 150 W.
UNASSIGNED: Stone mass (stone weight) was significantly lower after stone ablation independently of the stone type or the laser settings. Significantly higher mass decrease and ablation rate were detected in high-power compared to low-power settings. In the experiment, the highest temperature recorded was 32°C at 152 W. At 120 W and 105 W, the peak temperatures didn\'t reach 30°C. In the clinical study, a stone-free rate of 100% and a mean operative time of 43 ± 18 min were reported. All patients stayed in the hospital for one day except for one who presented minor hematuria. Additional complications did not occur.
UNASSIGNED: Ho:YAG laser lithotripsy > 100 W is an effective, fast and safe modality for the treatment of bladder calculi.

In this study, we aimed to evaluate the effect of HPL on different parameters by different centers and urologists. While doing this, we evaluated different parameters by comparing HPL(High Power laser) and LPL(Low-power laser). This is an observational, retrospective, comparative, multicentric study of prospectively organised database. A total of 217 patients who underwent RIRS for kidney stones smaller than 2 cm in three different centers were included in the study. The patients were divided into two groups; LPL used (Group1, n:121 patients) and HPL used (Group2, n:96). Propensity score matching was done in the data analysis part. After matching, a total of 192 patients, 96 patients in both groups, were evaluated. There was no difference between the groups regarding age, gender, stone side, and stone location. The stone-free rate on the first day was 80.3% in Group 1, it was 78.1% in Group 2 (p = 0.9). In the third month, it was 90.7% in Group 1 and 87.5% in Group 2 (p:0.7).Hospitalization duration was significantly higher in Group 1. (2.35 ± 2.27 days vs. 1.42 ± 1.10 days; p < 0.001).The operation duration was 88.70 ± 29.72 min in Group1 and 66.17 ± 41.02 min in Group2 (p < 0.001). The fluoroscopy time (FT) was 90.73 ± 4.79 s in Group 1 and 50.78 ± 5.64 s in Group 2 (p < 0.001). Complications according to Clavien Classification, were similar between the groups(p > 0.05). According to our study similar SFR and complication rates were found with HPL and LPL. In addition, patients who used HPL had lower operation time, hospital stay, and fluoroscopy time than the LPL group. Although high-power lasers are expensive in terms of cost, they affect many parameters and strengthen the hand of urologists thanks to the wide energy and frequency range they offer.

Objective: The purpose of this study was to review the literatures regarding the treatment outcomes of applying laser to the infected sites in immediate implant placement. The review tended to primarily target a question: does applying high-power laser have any positive effect on infected sites in immediate implant placement? Background: Although immediate placement of dental implants has been referred to as a predictable and successful procedure, it is prone to the presence of infection that interferes with the healing process, and triggers the failure of implants. Materials and methods: A thorough electronic database search was conducted on PubMed/Medline, Embase, Web of Science, Google Scholar, and the Cochrane library in compliance with the Preferred Reporting Items for Systematic Reviews and Meta-Analyses statement. Two writers worked separately on screening the eligible studies, assessing whether there was a risk of bias, and extracting the required data. Results: Five out of the 60 studies nominated by the database search matched the inclusion criteria. The studies were carried out on a total of 192 patients with 296 implants in all. Ultimately, the study focused on 245 implants whose infected bed had been already decontaminated and prepared with the help of the high-intensity laser, used either alone or in combination with other approaches before implantation. With only nine failures, the implants inserted in infected and irradiated areas had a 96.3% overall survival rate. Conclusions: Taking the limitations of the review into account, the authors arrived at the conclusion that high-power laser irradiation can be beneficial for immediate implant placement in infected sites.

The objective of this study was to describe the histological artifacts caused by high-power laser use compared to cold scalpel surgery in oral soft tissue lesions. Clinical studies that evaluated and compared histological artifacts resulting from the use of high-power lasers and cold scalpels in oral soft tissue lesions biopsies were retrieved from seven databases and four grey literatures, up to July 2022. The risk of bias was investigated using the ROBINS-I tool. The certainty of the evidence was assessed using the Grading of Recommendations, Assessment, Development, and Evaluation approach. Seven studies were eligible for qualitative analysis. Based on the results obtained, those four studies had a low risk of bias, and three studies had an unclear risk of bias. The certainty of the evidence was classified as low. Limited evidence showed that epithelial artifacts such as loss of intraepithelial and subepithelial adhesions, accompanied by pyknotic, fusiform, and/or hyperchromic nuclei, were more common when a high-power laser device was used. Four articles reported that the use of high-power lasers did not interfere with the histopathological diagnosis of oral soft tissue lesions. Due to the heterogeneity of the data, a meta-analysis was not performed. Compared to the use of cold scalpels, histological artifacts, particularly those observed in epithelial tissue, are more common when high-powered lasers are used in oral lesions biopsies. The eligibility criteria and adequate indications of high-power lasers in different oral soft tissue lesion treatments must be respected to avoid tissue artifacts that impair precise histopathological diagnosis.

Phase-modulated (PM) spectral failsafe systems are necessary to promptly terminate amplification processes following accidental seeding of a high-power laser chain with a non-PM pulse to prevent optical damage. In this work, we present a reliable spectral failsafe system that can indicate the presence or absence of sufficient PM light. This requirement is met by combining dual temperature-sensitive fiber Bragg gratings detection with high-speed RF amplitude comparisons. The failsafe trigger signal is generated when the spectral power at the peak sideband exceeds that at the center. The spectral failsafe system has the ability to distinguish between adequate and inadequate PM pulses, and it exhibits significant robustness in pulse width, TEC temperature drift, and DFB wavelength drift in experiments, making it valuable for safe high-power laser operations and providing a useful reference for other detection system designs.

High-power laser delivery in the mid-infrared via hollow-core fibers is attractive, but it is too difficult to be fabricated using chalcogenide glasses. Here, we designed a mid-infrared hollow-core anti-resonant chalcogenide fiber (HC-ARCF) with a simplified Kagome cladding micro-structure for the first time. Then, the fiber was firstly fabricated through a precision mechanical drilling and pressured fiber drawing method. Ultra-thin walls of 2μm in the fiber lead to the fewest resonance peaks in the 2-5μm among all reported HC-ARCFs. All the fundamental mode, the second-order mode, tube mode and node mode in the fiber were excited and observed at 1550 nm. The power and spectral properties of the core and cladding of HC-ARCF are studied for the first time. The fiber can deliver high-power of 4.84 W without damage with core-coupling, while the threshold of the node in the cladding is only 3.5 W. A broadening of the output spectrum from 1.96 to 2.41μm due to the high nonlinearity at the node was successfully observed under short-pulse laser pumping at 2μm. The potentials of the fiber used for mid-infrared high-power laser delivery via core, or nonlinear laser generation via node, were thus demonstrated.

The expanded uncertainty of the measured Brillouin scattering shift frequencies is essential in assessing the measurements of parameters of various materials. We describe the general operation principles of a Brillouin light scattering (BLS) spectrometer with a high-power laser and a scanning tandem Fabry-Pérot interferometer (TFPI) for material characterization. Various uncertainty components have been analyzed for the BLS spectrometer following the Guide to the Expression of Uncertainty in Measurement (GUM). The expanded relative uncertainty in the measured Brillouin frequency shift of 15.70 GHz for polymethyl methacrylate (PMMA) was estimated to be 0.26%. The calculated Brillouin frequency shift (based on material properties of PMMA) was determined to be 15.44 GHz with expanded relative uncertainty of 2.13%. It was shown that the measured and calculated Brillouin frequency shifts for PMMA agree within their expanded uncertainties. The TFPI-based BLS spectrometer can be used to measure the longitudinal modulus of materials with an expanded uncertainty of 1.9%, which is smaller than that of the ultrasonic velocity-based method (estimated to be 2.9%).

This case report describes the efficacy and advantages of using a high-power diode laser in non-contact mode to remove racial melanin pigmentation from the oral mucosa in an aesthetically sensible area to reduce thermal damage and promote better postoperative results. In the presented case, the lesion was removed under local anesthesia in a single session using high-power diode equipment with circular movements over the lesion (10 seconds maximum for each irradiation cycle, with 30 seconds for thermal relaxation, for a total of two cycles), maintaining an average distance of 2-3 mm from the target tissue without fiber activation (continuous wave, 2 W, delivered by quartz fiber with 300 µ). The patient did not report immediate postoperative pain; however, analgesic use was recorded during the first day after the surgical procedure. The biological response and cosmetic results were satisfactory, with proper lesion removal and adequate cicatrization observed during a two-year follow-up period, without complications or compromise of periodontal tissue esthetics.

UNASSIGNED: The aim of this article was to enumerate the differences in immediate and postoperative outcomes for holmium laser enucleation of the prostate (HoLEP) performed with low-power (LP) or high-power (HP) laser settings through a systematic review of comparative studies.
UNASSIGNED: We performed a systematic literature review using MEDLINE, EMBASE, and Cochrane Central Controlled Register of Trials. Potential clinical differences among LP and HP HoLEP were determined using the PICOS (Patient Intervention Comparison Outcome Study type) model, where outcomes were surgical time, operative efficiency, postoperative catheterization time, length of hospital stay, blood transfusion, incontinence rate, maximum urinary flow rate (QMax) and International Prostatic Symptom score (IPSS). Retrospective, prospective nonrandomized, randomized studies, and meeting abstracts were considered.
UNASSIGNED: A total of five studies were included for meta-analysis. No significant differences between LP and HP HoLEP were evidenced in terms of intraoperative variables (surgical time, surgical efficiency); postoperative outcomes (length of stay, length of catheterization); postoperative complications; functional results (IPSS; Qmax). Urinary incontinence rate did not differ between the two groups (OR 0.95, 95% CI 0.362.47, p = 0.91).
UNASSIGNED: The study shows equal outcomes in outcomes from HoLEP performed with LP or HP energy settings. Even if further comparative studies are still needed to increase the level of evidence, those results encourage a further clinical adoption of LP HoLEP.

High average power femtosecond lasers have made spectacular progress in the last decades - moving from laboratory-based systems with maximum average powers of tens of watts to kilowatt-class mature industrial systems in a short time. The availability of such systems opens new possibilities in many fields; one of the most prominent ones that have driven many of these technological advances is precise high-speed material processing, where ultrashort pulses have long been recognized to provide highest precision processing of virtually any material, and high average power extends these capabilities to highest processing rates. Here, we focus our attention on one high-average power technology with large unexplored potential for this specific application: directly modelocked multi-MHz repetition frequency high-power thin-disk oscillators. We review their latest state-of-the-art and discuss future directions and challenges, specifically with this application field in mind.