Aqueous suspensions containing crystalline drug in the sub-micron range is a favorable platform for long-acting injectables where particle size can be used to obtain a desired plasma-concentration profile. Stabilizers are added to the suspensions and screened extensively to define the optimal formulation composition. In the initial formulation screening the amount of drug compound can be limited, necessitating milling methods for small-volume screening predictable for scale-up. Hence, adaptive focused ultrasound was investigated as a potential milling method for rapid small-volume suspensions by identifying the critical process parameters during preparation. Suspensions containing drug compounds with different mechanical properties and thereby grindability, i.e., cinnarizine, haloperidol, and indomethacin with brittle, elastic, and plastic properties, respectively, were investigated to gain an understanding of the manufacturing with adaptive focused acoustics as well as comparison to already established milling techniques. Using a DoE-design, peak incident power was identified as the most crucial process parameter impacting the milling process for all three compounds. It was possible to decrease the sizes of drug particles to micron range after one minute of focused ultrasound exposure which was superior compared to other milling techniques (e.g., non-focused ultrasound exposure). The addition of milling beads decreased the drug particle sizes even further, thus to a lower degree than other already established milling techniques such as milling by dual centrifugation. This study thereby demonstrated that adaptive focused ultrasonication was a promising method for rapid homogenization and particle size reduction to micron range for different compounds varying in grindability without altering the crystalline structure.

Ultrasonic humidifiers are commonly used in households to maintain indoor humidity and generate a large number of droplets or spray aerosols. However, there have been various health concerns associated with humidifier use, largely due to aerosols generated during operation. Here, we investigated the size distribution, chemical composition, and charged fraction of aerosol particles emitted from commercial ultrasonic humidifiers. Heavy metals in water used for humidifiers were found to be highly enriched in the ultrasonic humidifier aerosols (UHA), with the enrichment factors ranging from 102 to 107. This enrichment may pose health concerns for the building occupants, as UHA concentrations of up to 106 particles/cm3 or 3 mg/m3 were observed. Furthermore, approximately 90% of UHA were observed to be electrically charged, for the first time according to our knowledge. Based on this discovery, we proposed and tested a new method to remove UHA by using a simple electrical field. The designed electrical field in this work can efficiently remove 81.4% of UHA. Therefore, applying this electrical field could be an effective method to significantly reduce the health risks by UHA.

Separating an endodontic instrument is one of the most frequent errors during a root canal treatment. If endodontic instruments get separated, it could hinder disinfection and prevent access to the apical portion of the root. It compromises the success of the treatment by impeding the proper debris removal from the canal. But now that techniques and tools have advanced, it is feasible to remove a separated instrument from the root canal successfully. This case report presents the management of a separated instrument, demonstrating the successful removal of the separated instrument.

Eggs are a valuable source of nutrients, but they represent a food safety risk due to the presence of microbes. In this work, three types of egg liquids (albumen, yolk and whole egg) previously contaminated with E. coli were treated with ultrasound (US) and a combination of ultrasound and low (55 °C) temperature (US+H). The US treatment parameters were 20 and 40 kHz and 180 and 300 W power and a 30, 45 or 60 min treatment time. The ultrasonic treatment alone resulted in a reduction in the microbial count of less than 1 log CFU, while the US+H treatment resulted in a reduction in CFU counts to below detectable levels in all three egg liquids. Heat treatment and ultrasound treatment had a synergistic effect on E. coli reduction. For all measurements, except for the whole egg samples treated with US, the 20 kHz treated samples showed a significantly (>90% probability level) lower bactericidal effect than the 40 kHz treated samples. PCA and aquaphotometric analysis of NIR spectra showed significant differences between the heat-treated groups\' (H and US+H) and the non-heat-treated groups\' (US and control) NIR spectra. LDA results show that heat-treated groups are distinguishable from non-heat-treated groups (for albumen 91% and for egg yolk and whole egg 100%).

Ultrasonic-assisted extraction using a natural deep eutectic solvent (UAE-NADES) is an efficient method for extracting grape seed polyphenols (GSPs). In this study, response surface methodology was used to optimize the extraction of GSPs with UAE-NADES, and the theoretical extraction rate of GSPs was 139.014 mg GAE/g, the actual extraction rate was 135.78 ± 1.3 mg GAE/g. A pseudo-second-order kinetic extraction fitting was established to simulate the extraction process and mechanism (R2 > 0.99). Analysis of antioxidant capacity, Fourier-infrared spectroscopy and scanning electron microscopy revealed that UAE-NADES works synergetically to maintain the stability of extracted GSPs. The results of high-performance liquid chromatography showed that catechin (41.14 mg/g) is the main component of GSPs in the extract. The UAE-NADES extraction of GSPs can inhibit the growth of Alternaria alternata at 0.25 mg GAE/g, while the GSPs extracted by other methods can effectively inhibit the growth of Alternaria alternata at 0.35 mg GAE/g. Thus, this study demonstrates that UAE-NADES is a high-efficiency means of extracting GSPs and, in a wider sense, is a promising extraction technology for the green utilization of waste resources.

This work explored the impact of ultrasound (US) on the activity, stability, and macrostructural conformation of cyclodextrin glycosyltransferase (CGTase) and how these changes could maximize the production of β-cyclodextrins (β-CDs). The results showed that ultrasonic pretreatment (20 kHz and 38 W/L) at pH 6.0 promoted increased enzymatic activity. Specifically, after sonication at 25 °C/30 min, there was a maximum activity increase of 93 % and 68 % when biocatalysis was carried out at 25 and 55 °C, respectively. For activity measured at 80 °C, maximum increase (31 %) was observed after sonication at 25 °C/60 min. Comparatively, US pretreatment at low pH (pH = 4.0) resulted in a lower activity increase (max. 28 %). These activation levels were maintained after 24 h of storage at 8 °C, suggesting that changes on CGTase after ultrasonic pretreatment were not transitory. These pretreatments altered the conformational structure of CGTase, revealed by an up to 11 % increase in intrinsic fluorescence intensity, and resulted in macrostructural modifications, such as a decrease in particle size and polydispersion index (up to 85 % and 45.8 %, respectively). Therefore, the sonication of CGTase under specific conditions of pH, time, and temperature (especially at pH 6.0/ 30 min/ 25 °C) promotes macrostructural changes in CGTase that induce enzyme activation and, consequently, higher production of β-CDs.

This study presents the design and development of an ultrasonic sensor as a fundamental tool for characterizing the properties of fluids and biofluids. The analysis primarily focuses on measuring the electrical parameters of the system, which correlate with the density and viscosity of the solutions, in sample volumes of microliters and with high temporal resolution (up to 1 data point per second). The use of this sensor allows the fast and non-destructive evaluation of the viscosity and density of fluids deposited on its free surface. The measurements are based on obtaining the impedance versus frequency curve and the phase difference curve (between current and voltage) versus frequency. In this way, characteristic parameters of the transducer, such as the resonance frequency, phase, minimum impedance, and the quality factor of the resonant system, can characterize variations in density and viscosity in the fluid under study. The results obtained revealed the sensor\'s ability to identify two parameters sensitive to viscosity and two parameters sensitive to density. As a proof of concept, the unfolding of the bovine albumin protein was studied, resulting in a curve that reflects its unfolding kinetics in the presence of urea.

OBJECTIVE: This study compared the effects of conventional, ultrasonic, and laser-activated irrigation (LAI) on penetration depth of three photosensitizers (PSs) in the root canal system.
METHODS: In this in vitro, experimental study, 120 extracted anterior teeth were decoronated such that the remaining root length was standardized at 12 mm. After root canal instrumentation with the ProTaper rotary system and irrigation with 5.25% NaOCl, the roots were assigned to 12 groups for the application of toluidine blue (TB), curcumin, and phycocyanin PSs combined with the LAI using erbium laser with 0.4 mm and 0.6 mm tips, ultrasonic activation, and conventional irrigation. The specimens were sectioned apicocoronally, and the dye penetration depth was quantified in the coronal, middle, and apical thirds under a stereomicroscope at x20 magnification. Data were analyzed by the Kruskal-Wallis and Dunn test (alpha=0.05).
RESULTS: The effects of irrigation technique, PS type, and their interaction on dye penetration depth were significant at the apical, middle, and coronal thirds (P<0.0001). TB + LAI with 0.4- and 0.6-mm laser tips showed the highest penetration depth while phycocyanin + LAI or conventional irrigation showed the lowest penetration depth at all areas. Dye penetration depth was the highest in the coronal, and the lowest in the apical third.
CONCLUSIONS: The LAI technique with erbium laser (0.4- and 0.6-mm tips) enhanced the penetration depth of TB. The tested irrigation techniques had no significant efficacy for enhancement of the penetration depth of curcumin and phycocyanin.

This study evaluated the setting time, pH, calcium ion release, solubility, and chemical structure of four calcium silicate sealers after ultrasonic activation (UA). Five sealers were evaluated: Sealer Plus (SP - control); Sealer Plus BC (SPBC), Bio C Sealers (BCS), Endosequence BC Sealer (EBC), and BioRoot RCS (BR). Ten groups were created based on the use or not of ultrasonic activation: SP; SP/UA; SPBC; SPBC/UA; BCS; BCS/UA; EBC; EBC/UA; BR; and BR/UA. Setting time was performed based on ISO 6876:2012 and ASTM C266-07 specifications. Solubility at 24hs, based on ISO 6876:2012. pH and calcium release were evaluated at 1, 24, 72, and 168hs. Raman spectroscopy was used to evaluate structural changes. Quantitative data were analyzed using One-Way ANOVA and Tukey post-hoc test (α=5%). Raman spectroscopy results were qualitatively analyzed. Setting times and solubility of all sealers were not affected by UA (p>0.05). The highest solubility was found for BCS, BCS/UA; and BR, BR/UA (p<0.05). After 24hs, calcium silicate sealers had higher pH than SP and SP/UA (p<0.05). BR and BR/UA had the highest pH at all time points. SP and SP/UA had stable pH at all time points. SP and SP/UA had the lowest calcium release values at all time points (p<0.05). EBC and EBC/UA calcium release significantly differ at 24,72 and 168hs (p<0.05). No chemical changes were observed during Raman spectroscopy. In conclusion, ultrasonic activation affected calcium ion release only for EndoSequence BC Sealer. Ultrasonic activation did not influence the initial and final setting time, solubility, pH, and chemical structure of any investigated sealers.

This study evaluated the effect of ultrasonic agitation on the filling capacity of ready-to-use calcium silicate-based sealer Bio-C Sealer (BCS, Angelus, Paraná, Brazil) or powder-liquid BioRoot RCS (BR, Septodont, Saint-Maur-des-Fossés, France) using curved artificial canals by micro-computed tomography (micro-CT). Additionally, flow (mm) and flow area (mm2) were evaluated for both materials. Acrylic resin main canal (60° curvature and 5 mm radius, with 3 lateral canals in the cervical, middle, and apical thirds) were prepared up to size 40/.05 (Prodesign Logic, Brazil). The agitation method was used with ultrasonic tip (US, Irrisonic, Helse, Brazil): BCS, BCS/US, BR, and BR/US. All specimens were filled using the single-cone technique. The samples were scanned by micro-CT (8,74 µm) after obturation. The percentage of filling material and voids were calculated. Flow was evaluated based on ISO 6876/2012 standards (mm) and area (mm2). The data were statistically analyzed using ANOVA and Tukey tests (α = 0.05). BR/US showed lower percentage of filling material in the lateral canals than and, BCS/US (p<0.05). BR/US resulted in a higher percentage of voids than BR in the lateral apical third (p<0.05). BCS showed higher flow than BR (p<0.05). BCS and BR presented proper filling capacity in the simulated curved canals regardless of the use of ultrasonic agitation. However, BR/US showed more voids in the apical third. BCS demonstrates higher filling ability.