Exploring efficient and comprehensive utilization of agricultural waste to produce high value-added products has been global research hotspot. In this study, a novel process for integrated production of xylose and docosahexaenoic acid (DHA) from hemicellulose and cellulose in corncob was developed. Corncob was treated with dilute H2SO4 at 121 °C for 1 h and xylose was readily produced with a recovery yield of 79.35 %. The corncob residue was then subject to alkali pretreatment under optimized conditions of 0.1 g NaOH/g dry solid, 60 °C for 2 h, and the contents of cellulose, hemicellulose, and lignin in the resulting residue were 87.49 %, 7.58 % and 2.31 %, respectively. The cellulose in the residue was easily hydrolyzed by cellulase, yielding 74.87 g/L glucose with hydrolysis efficiency of 77.02 %. Remarkably, the corncob residue hydrolysate supported cell growth and DHA production in Schizochytrium sp. ATCC 20888 well, and the maximum biomass of 32.71 g/L and DHA yield of 4.63 g/L were obtained, with DHA percentage in total fatty acids of 36.89 %. This study demonstrates that the corncob residue generated during xylose production, rich in cellulose, can be effectively utilized for DHA production by Schizochytrium sp., offering a cost-effective and sustainable alternative to pure glucose.

Biomass-based hydrogels have become a research hotspot because of their better biocompatibility. However, the preparation of biomass hydrogels is complicated, and they often need to be modified by introducing other substances. In this study, corncob pretreated with bisulfite (125-185 °C) was used as a raw material to prepare lignocellulose hydrogels. The results showed that directly using the pretreated sample without the washing step lowered the total hydrogel costs while preserving the lignosulfonate (LS) produced during pretreatment. The best tensile (54.1 kPa) and compressive (177.7 kPa) stresses were obtained for the hydrogel prepared from non-detoxified pretreated corncob at 165 °C (NCH-165). The sulfonic acid groups in LS could enhance the interaction between plant cellulose, thus improving its mechanical properties. The capacitor assembled from NCH-165 achieved an energy density of 236.1 Wh/kg at a power density of 499.7 W/kg and a high coulombic efficiency of more than 99 % after 2000 charge/discharge cycles. In conclusion, the present study simplifies the pathway for the preparation of flexible, conductive, and anti-freezing hydrogels by directly utilizing a non-detoxified bisulfite-pretreated corncob.

Plastic food packaging, with its harmful migration of microplastics and nanoplastics into food, presents significant ecological imbalance and human health risks. In this regard, using food and agricultural byproducts as packaging materials reduces environmental and economic concerns and supports their sustainable management. Herein, cellulosic residue from corncob was employed as a renewable source for developing biodegradable packaging films. It was solubilized in ZnCl2 solution, crosslinked with Ca2+ ions, and plasticized with sorbitol to form films and used to improve the shelf-life of raspberries. The optimized film possesses water vapor permeability, tensile strength, and elongation at break of 1.8(4) x10-10 g-1 s-1 Pa-1, 4.7(1) MPa, and 15.4(7)%, respectively. It displays UV-blocking and antioxidant properties and biodegrades within 29 days at 24% soil moisture. It preserves raspberries for 7 and 5 more days at room temperature and refrigeration conditions, respectively, compared to polystyrene film. Overall, more value addition could be envisioned from agricultural residues to minimize post-harvest losses and food waste through biodegradable packaging, which also aids in mitigating plastic perils.

The utilization of gypsum and biomass in environmental remediation has become a novel approach to promote waste recycling. Generally, raw waste materials exhibit limited adsorption capacity for heavy metal ions (HMIs) and often result in poor solid-liquid separation. In this study, through co-pyrolysis with corncob waste, titanium gypsum (TiG) was transformed into magnetic adsorbents (GCx, where x denotes the proportion of corncob in the gypsum-corncob mixture) for the removal of Cd(II) and Pb(II). GC10, the optimal adsorbent, which was composed primarily of anhydrite, calcium sulfide, and magnetic Fe3O4, exhibited significantly faster adsorption kinetics (rate constant k1 was 218 times and 9 times of raw TiG for Cd(II) and Pb(II)) and higher adsorption capacity (Qe exceeded 200 mg/g for Cd(II) and 400 mg/g for Pb(II)) than raw TiG and previous adsorbents. Cd(II) removal was more profoundly inhibited in a Cd(II) + Pb(II) binary system, suggesting that GC10 showed better selectivity for Pb(II). Moreover, GC10 could be easily separated from purified water for further recovery, due to its high saturation magnetization value (6.3 emu/g). The superior removal capabilities of GC10 were due to adsorption and surface precipitation of metal sulfides and metal sulfates on the adsorbent surface. Overall, these waste-derived magnetic adsorbents provide a novel and sustainable approach to waste recycling and the deep purification of multiple HMIs.

Ischaemic stroke presents a significant problem worldwide with no neuroprotective drugs available. Many of the failures in the search for neuroprotectants are attributed to failure to translate from pre-clinical models to humans, which has been combatted with rigorous pre-clinical stroke research guidelines. Here, we present post hoc analysis of a pre-clinical stroke trial, conducted using intraluminal filament transient middle cerebral artery occlusion in the stroke-prone spontaneously hypertensive rat, whereby unscheduled changes were implemented in the animal housing facility. These changes severely impacted body weight post-stroke resulting in a change from the typical body weight of 90.6% of pre-surgery weight post-stroke, to on average 80.5% of pre-surgery weight post-stroke. The changes also appeared to impact post-stroke blood pressure, with an increase from 215.4 to 240.3 mmHg between housing groups, and functional outcome post-stroke, with a 38% increased latency to contact in the sticky label test. These data highlight the importance of tightly controlled housing conditions when using physiological or behavioural measurements as a primary outcome.

This study investigated the efficient removal of cadmium ions from aqueous solutions using calcium oxide nanoparticles (CaO NPs) synthesized from waste hen eggshells using a Sol-gel method and supported on corncob bio-adsorbent. The synthesized CaO NPs were characterized using FT-IR, XRD, specific surface area, and TGA. Batch adsorption experiments were conducted to examine the influence of process parameters such as adsorbent dosages, initial Cd (II) concentrations, pH values, and contact times. XRD analysis revealed that the synthesized CaO nanoparticles had a size of 24.34 nm and a specific surface area of 77.4 m2/g. The optimal conditions for achieving the highest percent removal of cadmium (99.108%) were found to be an initial concentration of 55 ppm, pH 7, adsorbent dose of 0.75 g, and contact time of 50 min. The experimental removal efficiency closely matched the predicted value (99.0%), indicating the suitability of the method used in optimizing the removal of Cd (II) ions from aqueous solutions. These findings, corroborated by predicted values, underscore the efficacy of our method in optimizing cadmium removal. Based on these findings, it can be concluded that corncob-supported CaO NPs are optimized for their highest efficiency and hold great promise as a cost-effective and environmentally friendly solution for wastewater treatment with a focus on cadmium removal.

The production of corn generates a substantial amount of agro-industrial waste, with corncob accounting for a significant portion of this waste. In this study, we focused on utilizing corncob as a carbon source and inducer to simultaneously produce two valuable industrial enzymes, protease, and xylanase, using a recombinant strain of B. halodurans CM1. Interestingly, xylan-rich corncob not only enhanced the xylanase activity but also induced protease activity of the modified B. halodurans CM1 strain. The effect of corncob concentration on the coproduction of protease and xylanase was investigated. Corncob with 6 % concentration induced protease activity of 1020.7 U/mL and xylanase activity of 502.8 U/mL in a 7 L bioreactor under the condition of 1 vvm aeration, 250 rpm agitation, 37 °C temperature, initial pH 9.0, and 40 h incubation period. The protease produced was an alkalothermophilic enzyme whose highest activity was at pH 12 and 50 °C, and it belonged to a serine protease family. This alkalothermophilic protease\'s activity to some degree was reduced by Co2+, Mg2+, Fe2+, Zn2+, and K+, but enhanced by Ca2+ and Ni2+ (at 5 mM). The protease was stable even under the presence of a 15 % concentration of acetone, DMSO, ethanol, and isopropyl alcohol. The protease activity at 30 °C was not considerably changed by the presence of detergent, indicating excellent potential as a washing detergent additive. According to these findings, corncob has the potential to be a substrate for the coproduction of protease and xylanase, which have a wide range of industrial uses.

A key factor restricting the application of biochar in the steel industry is its high-quality upgrading. This paper evaluated the characteristics of hydrochar produced by HTC (hydrothermal carbonization) process of corncob to be used as a solid fuel. HTC temperatures (240-300 °C) and HTC water-reused times (1-3 times) were examined for their effects on hydrochar yield, physicochemical characteristics, and combustion properties. The results showed hydrochar yields, O/C, and H/C parameters decreased as HTC temperature and water-reused times increased, while its high heating value increased. Due to dehydration and decarboxylation, hydrochar showed similar characteristics to those in bituminous coal. The removal efficiency of alkali metal K reached 99% after HTC treatment. Carbonaceous hydrochar had become more compact, orderly, and stable with increasing amounts of aromatic functional groups, C = C, and C = O. Hydrochar, as a biofuel, has higher ignition energy and is more stable than corncob due to its high carbonaceous order degree. To calculate combustion kinetic parameters, the Kissinger-Akahira-Sunose (KAS) and Flynn-Wall-Ozawa (FWO) methods were applied. The results revealed that Eα (average activation energy) was quite similar between the two models. HC-300 had an Eα of 262 kJ/mol. HTC could be an efficient way to reutilize corncob biomass into clean biofuels with high calorific value.

The short-term composting based on corncob for preparing Pleurotus ostreatus cultivation medium originated from agricultural production practices and so lacked systematic investigation. In this study, the influences of a Dafen (15 mm, DFT) and Xiaofen (5 mm, XFT) initial particle size (IPS) of corncob on the microbial succession and compost quality were examined. Results demonstrated that XFT compost was better suited for mushroom cultivation due to its high biological efficiency of 70 % and the absence of contamination. The composting microbes differed significantly between the DFT and XFT composts. During composting, the genera of Bacillus, Acinetobacter, Lactobacillus, Streptomyces, and Paenibacillus were majorly found in the DFT compost, while Acinetobacter, Lactobacillus, Puccinia, Bacteroides, and Bacillus genera dominated the XFT compost. Kyoto Encyclopedia of Genes and Genomes (KEGG) analysis showed that throughout the thermophilic phase, XFT compost had much greater relative abundances of sequences relevant to energy, carbohydrate, and amino acid metabolism than DFT compost. Analysis of network correlations and Mantel tests indicated that IPS reduction could increase microbial interactions. Overall, adjusting the IPS of corncob to 5 mm increased microbial interactions, improved compost quality, and thereby boosted the P. ostreatus yield. These findings will be pertinent in optimizing the composting process of cultivation medium for P. ostreatus.

Endo-xylanase hydrolyzing xylan in cellulosic residues releasing xylobiose as the major product at neutral pH are desirable in the substitute sweeteners industry. In this study, two endo-xylanases were obtained from Streptomyces rochei and Bacillus velezensis. SrocXyn10 showed the highest identity of 77.22%, with a reported endo-xylanase. The optimum reaction temperature and pH of rSrocXyn10-Ec were pH 7.0 and 60°C, with remarkable stability at 45°C or pHs ranging from 4.5 to 11.0. rBvelXyn11-Ec was most active at pH 6.0 and 50°C, and was stable at 35°C or pH 3.5 to 10.5. Both rSrocXyn10-Ec and rBvelXyn11-Ec showed specific enzyme activities on wheat arabinoxylan (685.83 ± 13.82 and 2809.89 ± 21.26 U/mg, respectively), with no enzyme activity on non-xylan substrates. The Vmax of rSrocXyn10-Ec and rBvelXyn11-Ec were 467.86 U mg-1 and 3067.68 U mg-1, respectively. The determined Km values of rSrocXyn10-Ec and rBvelXyn11-Ec were 3.08 g L-1 and 1.45 g L-1, respectively. The predominant product of the hydrolysis of alkaline extracts from bagasse, corncob, and bamboo by rSrocXyn10-Ec and rBvelXyn11-Ec were xylooligosaccharides. Interestingly, the xylobiose content in hydrolysates by rSrocXyn10-Ec was approximately 80%, which is higher than most reported endo-xylanases. rSrocXyn10-Ec and rBvelXyn11-Ec could be excellent candidates to produce xylooligosaccharides at neutral/near-neutral pHs. rSrocXyn10-Ec also has potential value in the production of xylobiose as a substitute sweetener.