The identification of spray-drying processing parameters capable of producing particles suitable for pulmonary inhalation with retained bioactivity underpins the development of inhalable biotherapeutics. Effective delivery of biopharmaceuticals via pulmonary delivery routes such as dry powder inhalation (DPI) requires developing techniques that engineer particles to well-defined target profiles while simultaneously minimising protein denaturation. This study examines the simultaneous effects of atomisation gas flow rate on particle properties and retained bioactivity for the model biopharmaceutical lysozyme. The results show that optimising the interplay between atomisation gas flow rate and excipient concentration enables the production of free-flowing powder with retained bioactivity approaching 100%, moisture content below 4%, and D50 < 4 µm, at yields exceeding 50%. The developed methodologies inform the future design of protein-specific spray-drying parameters for inhalable biotherapeutics.

Pulmonary inflammations such as chronic obstructive pulmonary disease and cystic fibrosis are widespread and can be fatal, especially when they are characterized by abnormal mucus accumulation. Inhaled corticosteroids are commonly used for lung inflammations despite their considerable side effects. By utilizing particle engineering techniques, a combined dry powder inhaler (DPI) comprising nanosized ketoprofen-embedded mannitol-coated microparticles was developed. A nanoembedded microparticle system means a novel advance in pulmonary delivery by enhancing local pulmonary deposition while avoiding clearance mechanisms. Ketoprofen, a poorly water-soluble anti-inflammatory drug, was dispersed in the stabilizer solution and then homogenized by ultraturrax. Following this, a ketoprofen-containing nanosuspension was produced by wet-media milling. Furthermore, co-spray drying was conducted with L-leucine (dispersity enhancer) and mannitol (coating and mucuactive agent). Particle size, morphology, dissolution, permeation, viscosity, in vitro and in silico deposition, cytotoxicity, and anti-inflammatory effect were investigated. The particle size of the ketoprofen-containing nanosuspension was ~230 nm. SEM images of the spray-dried powder displayed wrinkled, coated, and nearly spherical particles with a final size of ~2 µm (nano-in-micro), which is optimal for pulmonary delivery. The mannitol-containing samples decreased the viscosity of 10% mucin solution. The results of the mass median aerodynamic diameter (2.4-4.5 µm), fine particle fraction (56-71%), permeation (five-fold enhancement), and dissolution (80% release in 5 min) confirmed that the system is ideal for local inhalation. All samples showed a significant anti-inflammatory effect and decreased IL-6 on the LPS-treated U937 cell line with low cytotoxicity. Hence, developing an innovative combined DPI comprising ketoprofen and mannitol by employing a nano-in-micro approach is a potential treatment for lung inflammations.

Respirable particles are integral to effective inhalable therapeutic ingredient delivery, demanding precise engineering for optimal lung deposition and therapeutic efficacy. This review describes different physicochemical properties and their role in determining the aerodynamic performance and therapeutic efficacy of dry powder formulations. Furthermore, advances in top-down and bottom-up techniques in particle preparation, highlighting their roles in tailoring particle properties and optimizing therapeutic outcomes, are also presented. Practices adopted for particle engineering during the past 100 years indicate a significant transition in research and commercial interest in the strategies used, with several innovative concepts coming into play in the past decade. Accordingly, this article highlights futuristic particle engineering approaches such as electrospraying, inkjet printing, thin film freeze drying, and supercritical processes, including their prospects and associated challenges. With such technologies, it is possible to reshape inhaled therapeutic ingredient delivery, optimizing therapeutic benefits and improving the quality of life for patients with respiratory diseases and beyond.

In this review, an extensive analysis of dry powder inhalers (DPIs) is offered, focusing on their characteristics, formulation, stability, and manufacturing. The advantages of pulmonary delivery were investigated, as well as the significance of the particle size in drug deposition. The preparation of DPI formulations was also comprehensively explored, including physico-chemical characterization of powders, powder processing techniques, and formulation considerations. In addition to manufacturing procedures, testing methods were also discussed, providing insights into the development and evaluation of DPI formulations. This review also explores the design basics and critical attributes specific to DPIs, highlighting the significance of their optimization to achieve an effective inhalation therapy. Additionally, the morphology and stability of 3 DPI capsules (Spiriva, Braltus, and Onbrez) were investigated, offering valuable insights into the properties of these formulations. Altogether, these findings contribute to a deeper understanding of DPIs and their development, performance, and optimization of inhalation dosage forms.

Tailoring the hydrophobicity of supramolecular assembly building blocks enables the fabrication of well-defined functional materials. However, the selection of building blocks used in the assembly of metal-phenolic networks (MPNs), an emerging supramolecular assembly platform for particle engineering, has been essentially limited to hydrophilic molecules. Herein, we synthesized and applied biscatechol-functionalized hydrophobic polymers (poly(methyl acrylate) (PMA) and poly(butyl acrylate) (PBA)) as building blocks to engineer MPN particle systems (particles and capsules). Our method allowed control over the shell thickness (e.g., between 10 and 21 nm), stiffness (e.g., from 10 to 126 mN m-1 ), and permeability (e.g., 28-72 % capsules were permeable to 500 kDa fluorescein isothiocyanate-dextran) of the MPN capsules by selection of the hydrophobic polymer building blocks (PMA or PBA) and by controlling the polymer concentration in the MPN assembly solution (0.25-2.0 mM) without additional/engineered assembly processes. Molecular dynamics simulations provided insights into the structural states of the hydrophobic building blocks during assembly and mechanism of film formation. Furthermore, the hydrophobic MPNs facilitated the preparation of fluorescent-labeled and bioactive capsules through postfunctionalization and also particle-cell association engineering by controlling the hydrophobicity of the building blocks. Engineering MPN particle systems via building block hydrophobicity is expected to expand their use.

Achieving homogeneity and reproducibility in the size, shape, and morphology of active pharmaceutical ingredient (API) particles is crucial for their successful manufacturing and performance. Herein, we describe a new method for API particle engineering using melt-jet printing technology as an alternative to the current solvent-based particle engineering methods. Paracetamol, a widely used API, was melted and jetted as droplets onto various surfaces to solidify and form microparticles. The influence of different surfaces (glass, aluminum, polytetrafluoroethylene, and polyethylene) on particle shape was investigated, revealing a correlation between substrate properties (heat conduction, surface energy, and roughness) and particle sphericity. Higher thermal conductivity, surface roughness, and decreased surface energy contributed to larger contact angles and increased sphericity, reaching a near-perfect micro-spherical shape on an aluminum substrate. The integrity and polymorphic form of the printed particles were confirmed through differential scanning calorimetry and X-ray diffraction. Additionally, high-performance liquid chromatography analysis revealed minimal degradation products. The applicability of the printing process to other APIs was demonstrated by printing carbamazepine and indomethacin on aluminum surfaces, resulting in spherical microparticles. This study emphasizes the potential of melt-jet printing as a promising approach for the precise engineering of pharmaceutical particles, enabling effective control over their physiochemical properties.

The objective of this study was to explore the aerosolization performance of powders produced with different mesh nebulizer sources in the initial design of a new small-particle spray dryer system. An aqueous excipient enhanced growth (EEG) model formulation was spray dried using different mesh sources and the resulting powders were characterized based on (i) laser diffraction, (ii) aerosolization with a new infant air-jet dry powder inhaler, and (iii) aerosol transport through an infant nose-throat (NT) model ending with a tracheal filter. While few differences were observed among the powders, the medical-grade Aerogen Solo (with custom holder) and Aerogen Pro mesh sources were selected as lead candidates that produced mean fine particle fractions <5 µm and <1 µm in ranges of 80.6-77.4% and 13.1-16.0%, respectively. Improved aerosolization performance was achieved at a lower spray drying temperature. Lung delivery efficiencies through the NT model were in the range of 42.5-45.8% for powders from the Aerogen mesh sources, which were very similar to previous results with a commercial spray dryer. Ultimately, a custom spray dryer that can accept meshes with different characteristics (e.g., pore sizes and liquid flow rates) will provide particle engineers greater flexibility in producing highly dispersible powders with unique characteristics.

Particulate amorphous solid dispersions (ASDs) have been recognised for their potential to enhance the performance of various solid dose forms, especially oral bioavailability and macromolecule stability. However, the inherent nature of spray-dried ASDs leads to their surface cohesion/adhesion, including hygroscopicity, which hinders their bulk flow and affects their utility and viability in terms of powder production, processing, and function. This study explores the effectiveness of L-leucine (L-leu) coprocessing in modifying the particle surface of ASD-forming materials. Various contrasting prototype coprocessed ASD excipients from both the food and pharmaceutical industries were examined for their effective coformulation with L-leu. The model/prototype materials included maltodextrin, polyvinylpyrrolidone (PVP K10 and K90), trehalose, gum arabic, and hydroxypropyl methylcellulose (HPMC E5LV and K100M). The spray-drying conditions were set such that the particle size difference was minimised, so that it did not play a substantial role in influencing powder cohesion. Scanning electron microscopy was used to evaluate the morphology of each formulation. A combination of previously reported morphological progression typical of L-leu surface modification and previously unreported physical characteristics was observed. The bulk characteristics of these powders were assessed using a powder rheometer to evaluate their flowability under confined and unconfined stresses, flow rate sensitivities, and compactability. The data showed a general improvement in maltodextrin, PVP K10, trehalose and gum arabic flowability measures as L-leu concentrations increased. In contrast, PVP K90 and HPMC formulations experienced unique challenges that provided insight into the mechanistic behaviour of L-leu. Therefore, this study recommends further investigations into the interplay between L-leu and the physico-chemical properties of coformulated excipients in future amorphous powder design. This also revealed the need to enhance bulk characterisation tools to unpack the multifactorial impact of L-leu surface modification.

The emergence of novel respiratory infections (e.g., COVID-19) and expeditious development of nanoparticle-based COVID-19 vaccines have recently reignited considerable interest in designing inhalable nanoparticle-based drug delivery systems as next-generation respiratory therapeutics. Among various available devices in aerosol delivery, dry powder inhalers (DPIs) are preferable for delivery of nanoparticles due to their simplicity of use, high portability, and superior long-term stability. Despite research efforts devoted to developing inhaled nanoparticle-based DPI formulations, no such formulations have been approved to date, implying a research gap between bench and bedside. This review aims to address this gap by highlighting important yet often overlooked issues during pre-clinical development. We start with an overview and update on formulation and particle engineering strategies for fabricating inhalable nanoparticle-based dry powder formulations. An important but neglected aspect in in vitro characterization methodologies for linking the powder performance with their bio-fate is then discussed. Finally, the major challenges and strategies in their clinical translation are highlighted. We anticipate that focused research onto the existing knowledge gaps presented in this review would accelerate clinical applications of inhalable nanoparticle-based dry powders from a far-fetched fantasy to a reality.

Biopharmaceuticals have established an indisputable presence in the pharmaceutical pipeline, enabling highly specific new therapies. However, manufacturing, isolating, and delivering these highly complex molecules to patients present multiple challenges, including the short shelf-life of biologically derived products. Administration of biopharmaceuticals through inhalation has been gaining attention as an alternative to overcome the burdens associated with intravenous administration. Although most of the inhaled biopharmaceuticals in clinical trials are being administered through nebulization, dry powder inhalers (DPIs) are considered a viable alternative to liquid solutions due to enhanced stability. While freeze drying (FD) and spray drying (SD) are currently seen as the most viable solutions for drying biopharmaceuticals, spray freeze drying (SFD) has recently started gaining attention as an alternative to these technologies as it enables unique powder properties which favor this family of drug products. The present review focus on the application of SFD to produce dry powders of biopharmaceuticals, with special focus on inhalation delivery. Thus, it provides an overview of the critical quality attributes (CQAs) of these dry powders. Then, a detailed explanation of the SFD fundamental principles as well as the different existing variants is presented, together with a discussion regarding the opportunities and challenges of SFD as an enabling technology for inhalation-based biopharmaceuticals. Finally, a review of the main formulation strategies and their impact on the stability and performance of inhalable biopharmaceuticals produced via SDF is performed. Overall, this review presents a comprehensive assessment of the current and future applications of SFD in biopharmaceuticals for inhalation delivery.