In this study, RM (red mud) was acidified with sulfuric acid, and the acidified ARM (acidified red mud) was utilized as an innovative adsorption material for treating antibiotic-containing wastewater. The adsorption conditions, kinetics, isotherms, thermodynamics, and mechanism of ARM for CIP (ciprofloxacin) were investigated. The characterization of the ARM involved techniques such as scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD), X-ray fluorescence (XRF), thermogravimetric analysis (TGA), and NH3-TPD analysis. Adsorption studies employed a response surface methodology (RSM) for the experimental design. The results showed that ARM can absorb CIP effectively. The RSM optimal experiment indicated that the most significant model terms influencing adsorption capacity were solution pH, CIP initial concentration, and ARM dosage, under which the predicted maximum adsorption capacity achieved 7.30 mg/g. The adsorption kinetics adhered to a pseudo-second-order model, while equilibrium data fitted the Langmuir-Freundlich isotherm, yielding maximum capacity values of 7.35 mg/g. The adsorption process occurred spontaneously and absorbed heat, evidenced by ΔGθ values between -83.05 and -91.50 kJ/mol, ΔSθ at 281.6 J/mol/K, and ΔHθ at 0.86 kJ/mol. Analysis using attenuated total reflection Fourier-transform infrared spectroscopy (ATR-FTIR) indicated a complex reaction between the Al-O in the ARM and the ester group -COO in CIP. The C=O bond in CIP was likely to undergo a slight electrostatic interaction or be bound to the internal spherical surface of the ARM. The findings indicate that ARM is a promising and efficient adsorbent for CIP removal from wastewater.

ZnO nanorod nonwoven fabrics (ZNRN) were developed through hydrothermal synthesis to facilitate the prevention of the transmission of respiratory pathogens. The superhydrophobicity and antibacterial properties of ZNRN were improved through the response surface methodology. The synthesized material exhibited significant water repellency, indicated by a water contact angle of 163.9°, and thus demonstrated antibacterial rates of 91.8% for Escherichia coli (E. coli) and 79.75% for Staphylococcus aureus (S. aureus). This indicated that E. coli with thinner peptidoglycan may be more easily killed than S. aureus. This study identified significant effects of synthesis conditions on the antibacterial effectiveness, with comprehensive multivariate analyses elucidating the underlying correlations. In addition, the ZnO nanorod structure of ZNRN was characterized through SEM and XRD analyses. It endows the properties of superhydrophobicity (thus preventing bacteria from adhering to the ZNRN surface) and antibacterial capacity (thus damaging cells through the puncturing of these nanorods). Consequently, the alignment of two such features is desired to help support the development of personal protective equipment, which assists in avoiding the spread of respiratory infections.

The extraction of active ingredients from traditional Chinese medicine has received considerable attentions. In this study, 16 kinds of natural deep eutectic solvent (NADES) with ultrasonic were selected to extract saponins from purple yam root and the extraction mechanism was investigated. The results showed that chloride/acrylic acid (1:2; n/n) had the highest extraction yield for saponins. The optimal extraction process parameters were 24% water content, 20 mL/g liquid-solid ratio, and ultrasonic extraction for 85 min (81 °C, 600 W). The extraction rate (ER) of purple yam saponins was 0.935%, close to the fitted result of 96.5 mg/g. Molecular dynamics simulations and FT-IR results showed that the NADES may extract the saponin constituents from purple yam through hydrogen bonding. Compared with traditional extraction methods and molecularly imprinted polymer methods, NADES has a higher ER and lower cost (1.53 $/g), which provides a reference for subsequent industrial quantitative production.

The Hippophae rhamnoides L. pomace was generated in the production process for juice, wine of food industry. To expand the application of pomace, the extraction process optimization, enrichment and identification of triterpene acids were performed in this study. The extraction yield was 14.87% under optimal ultrasound-assisted extraction techniques performed via response surface methodology. The extract was subsequently purified to obtain the triterpenoid acid enrichment fraction (TPF) with the content of 75.23% ± 1.45%. 13 triterpenoid acids were identified via UPLC-Triple-TOF MS/MS and further semi-quantified through comparison with triterpenoid acid standards. TPF exhibited a strong inhibitory effect on α-glucosidase with IC50 value of 5.027 ± 0.375 μg/mL, as determined via enzyme inhibition experiment and molecular docking. Additionally, the TPF significantly reduced postprandial glucose levels, as revealed via carbohydrate tolerance tests, as well as ameliorate serum lipid profiles. Therefore, pomace may be a promising resource of functional food components with therapeutic and commercial values.

A novel method is introduced for extracting and enriching Cd(II) and Pb(II) from edible oils using glutathione disulfide (GSSG) as both an extractant and a phase-separation agent. The ions in the oils were initially extracted into an aqueous solution containing GSSG. After mixing the solution with acetonitrile at the appropriate volume ratio, a new phase formed, resulting in enrichment of the analytes. The experimental conditions were optimized using response surface methodology with a central composite design. Under optimal conditions, the method offered a combined enrichment factor of >660, with combined extraction efficiencies of 84.31% and 83.35% for Cd(II) and Pb(II), respectively. Finally, the method was conjugated to capillary electrophoresis to determine Cd(II) and Pb(II) in edible oil samples, with detection limits of 0.45 and 1.24 ppb, respectively. In comparison to traditional approaches, the GSSG-based method demonstrates rapidity, efficiency, and recyclability in extracting heavy metal ions from complex matrices.

Manufactured sand (MS) is a promising alternative aggregate to quartz sand (QS) in ultra-high-performance concrete (UHPC) in the preparation of ultra-high-performance manufactured sand concrete (UHPMC), which possesses the characteristics of high strength, low cost, and environmental friendliness. In this study, the effects of variable compositional characteristics including the water-binder ratio, the stone powder (SP) content, and the MS replacement ratio on the mechanical and flexural strength of UHPMC were compared and analyzed based on response surface methodology (RSM). Meanwhile, the damage characteristics of UHPMC during compressive and flexural stress were monitored and evaluated using acoustic emission (AE) technology. The results reveal that the compressive and flexural strengths of UHPMC are both negatively correlated with the water-binder ratio, while they are positively correlated with the MS replacement rate. They tend to firstly increase and subsequently decrease with the increase in the stone powder content. In the load-displacement curve of concrete with a high MS replacement ratio and a low water-binder ratio, the slope in the elastic stage is steeper, the stiffness is higher, and the bending toughness and ductility are also better. The specimens with a 10% to 0% stone powder content present a steeper elastic phase slope, a slightly higher stiffness, and superior ductility. The specimens with a low MS replacement ratio and a high water-binder ratio display earlier cracking and weaker resistance, and the destruction process is complex and very unstable. The damage mode analysis based on RA-AF shows that an increase in the MS replacement ratio and a decrease in the water-binder ratio can both reduce the tensile cracking of UHPMC specimens under a four-point bending test. Although 10% stone powder can marginally slow down crack growth, the failure mode is not significantly affected.

This study aims to establish a rapid and convenient microwave-assisted digestion method for sample pretreatment to determine amino acid profiles in natural products. This method was applied to analyze the amino acid profiles of Quisqualis Fructus (QF) from different planted origins. The microwave-assisted digestion conditions were optimized by a response surface methodology (RSM), and 17 amino acids in different planted origins of QF were determined by an automatic amino acid analyzer according to the optimized digestion conditions. The contents of 17 amino acids in QF from different planted origins were further analyzed by fingerprint and chemometric analysis. The temperature of microwave digestion at 167 °C, time of microwave digestion at 24 min, and a solid-liquid ratio of 46.5 g/mL was selected as the optimal digestion conditions. The total content of 17 amino acids in QF from different planted origins ranged from 71.88 to 91.03 mg/g. Amino acid composition and nutritional evaluation indicated that the content of medicinal amino acids was higher than aromatic amino acids. The results of fingerprint analysis reflected that the similarity between the 16 batches of QF ranged from 0.889 to 0.999, while chemometrics analysis indicated amino acid content in QF varied from different planted origins, and six important differential amino acids were screened. Compared with the traditional extraction method, microwave-assisted digestion with response surface optimized has the advantages of rapidity, convenience, and reliability, which could be used to study the amino acid profiles in natural products. The amino acid profile of QF indicated that it has a rich medicinal nutritional value. Different planted origins of QF have a high degree of similarity and could be effectively distinguished by chemometric analysis.

Xenocoumacin 1 (Xcn 1), antibiotic discovered from secondary metabolites of Xenorhabdus nematophila, had the potential to develop into a new pesticide due to its excellent activity against bacteria, oomycetes and fungi. However, the current low yield of Xcn1 limits its development and utilization. To improve the yield of Xcn1, response surface methodology was used to determine the optimal composition of fermentation medium and one factor at a time approach was utilized to optimize the fermentation process. The optimal medium composed of in g/L: proteose peptone 20.8; maltose 12.74; K2HPO4 3.77. The optimal fermentation conditions were that 25 °C, initial pH 7.0, inoculum size 10%, culture medium 75 mL in a 250 mL shake flask with an agitation rate of 150 rpm for 48 h. Xenorhabdus nematophila YL001 was produced the highest Xcn1 yield (173.99 mg/L) when arginine was added to the broth with 3 mmol/L at the 12th h. Compared with Tryptic Soy Broth medium, the optimized fermentation process resulted in a 243.38% increase in Xcn1 production. The obtained results confirmed that optimizing fermentation technology led to an increase in Xcn1 yield. This work would be helpful for efficient Xcn1 production and lay a foundation for its industrial production.

At present, excessive Fe3+ in daily water has become a threat to human health. Among the conventional detection methods for Fe3+, fluorescent probes have been applied on a large scale due to their simplicity and efficiency. However, the currently available fluorescent probes are difficult to synthesize, costly and environmentally unfriendly, limiting their applications. In this work, a fluorescent extract of Pterocarpus wood was successfully obtained, and the structure of some coumarin-based molecules in this extract was determined by 2D-NMR. Subsequently, the intensity of this fluorescence was optimized using response surface methodology (RSM), resulting in a high-intensity fluorescent probe. The probe was sensitive to the concentrations of Fe3+ and MnO4-, and could efficiently detects Fe3+ in the range of 2.7 μM-8.0 μM, with LOD and LOQ reaching 1.06 μM and 3.20 μM, respectively. Moreover, based on the strong complexation property of EDTA on Fe3+, this work designed the \"switch-on\" fluorescent probes. The experiment shows that both static and dynamic quenching exist in this system. The mechanism of complexation and oxidation of fluorescent molecules by the quencher is interpreted in the quenching reaction. In addition, the fluorescent probe has a high yield and low cost, it also performs well in actual water sample tests. This method is expected to be developed as a new way on Fe3+ detection.

In order to achieve numerical optimization of the pod pepper seed sowing device, the contact parameters of pod pepper seeds were calibrated, with the angle of repose used as the response value. A set of discrete element method (DEM) models of pod pepper seeds was developed to simulate the formation of seed repose angles using reverse engineering reconstruction techniques. An eight-factor, three-level response surface experiment based on the Box-Behnken central combination test method was performed to study the effects of various factors on the angle of repose of seeds. The angle of repose obtained from physical experiments with a value of 27.56° was taken as the target value. The optimal combination of parameters is obtained as follows: seed Poisson\'s ratio of 0.22, seed shear modulus of 15.47 MPa, seed-to-seed static friction coefficient of 0.25, seed-to-seed rolling friction coefficient of 0.67, seed-to-seed collision recovery coefficient of 0.64, seed-to-steel-plate static friction coefficient of 0.55, seed-to-steel-plate rolling friction coefficient of 0.45, and seed-to-steel plate collision recovery coefficient of 0.34. A two-sample t-test of the angle of repose obtained by the cylinder lifting method and the pumping plate method against the target value yielded P > 0.05, indicating the reliability of the simulation experiments.