Olive oil production is characterized by large amounts of waste, and yet is considerably highly valued. Olive pomace can serve as a cheap source of bioactive compounds (BACs) with important antioxidant activity. Novel technologies like Pulsed Electric Fields (PEF) and High Pressure (HP) and microwave (MW) processing are considered green alternatives for the recovery of BACs. Different microwave (150-600 W), PEF (1-5 kV/cm field strength, 100-1500 pulses/15 µs width), and HP (250-650 MPa) conditions, in various product/solvent ratios, methanol concentrations, extraction temperatures, and processing times were investigated. Results indicated that the optimal MW extraction conditions were 300 W at 50 °C for 5 min using 60% v/v methanol with a product/solvent ratio of 1:10 g/mL. Similarly, the mix of 40% v/v methanol with olive pomace, treated at 650 MPa for the time needed for pressure build-up (1 min) were considered as optimal extraction conditions in the case of HP, while for PEF the optimal conditions were 60% v/v methanol with a product/solvent ratio of 1:10 g/mL, treated at 5000 pulses, followed by 1 h extraction under stirring conditions. Therefore, these alternative extraction technologies could assist the conventional practice in minimizing waste production and simultaneously align with the requirements of the circular bioeconomy concept.

This study focused on synthesis of innovative hydrogels with electric field response from modified pineapple peel cellulose and hericium erinaceus chitosan and gelatin based on Schiff base reaction. A series of hydrogels were prepared by oxidized hydroxyethyl cellulose, gelatin and chitosan at different deacetylation degree via mild Schiff base reaction. Subsequently experiments towards the characterization of oxidized hydroxyethyl cellulose/gelatin/chitosan (OHGCS) hydrogel polymers were carried out by FTIR/XRD/XPS, swelling performances and electric response properties. The prepared hydrogels exhibited stable and reversible bending behaviors under repeated on-off switching of electric fields, affected by ionic strength, electric voltage and pH changes. The swelling ratio of OHGCS hydrogels was found reduced as deacetylation degree increasing and reached the maximum ratio ∼ 2250 % for OHGCS-1. In vitro drug releasing study showed the both curcumin loading capacity and release amount of Cur-OHGCS hydrogels arrived about 90 % during 6 h. Antioxidation assessments showed that the curcumin-loaded hydrogels had good antioxidation activities, in which, 10 mg Cur-OHGCS-1 hydrogel could reach to the maximum of about 90 % DPPH scavenging ratio. These results indicate the OHGCS hydrogels have potentials in sensor and drug delivery system.

BACKGROUND: The emergence of smartphones has sparked a transformation across multiple fields, with health care being one of the most notable due to the advent of mobile health (mHealth) apps. As mHealth apps have gained popularity, there is a need to understand their energy consumption patterns as an integral part of the evolving landscape of health care technologies.
OBJECTIVE: This study aims to identify the key contributors to elevated energy consumption in mHealth apps and suggest methods for their optimization, addressing a significant void in our comprehension of the energy dynamics at play within mHealth apps.
METHODS: Through quantitative comparative analysis of 10 prominent mHealth apps available on Android platforms within the United States, this study examined factors contributing to high energy consumption. The analysis included descriptive statistics, comparative analysis using ANOVA, and regression analysis to examine how certain factors impact energy use and consumption.
RESULTS: Observed energy use variances in mHealth apps stemmed from user interactions, features, and underlying technology. Descriptive analysis revealed variability in app energy consumption (150-310 milliwatt-hours), highlighting the influence of user interaction and app complexity. ANOVA verified these findings, indicating the critical role of engagement and functionality. Regression modeling (energy consumption = β₀ + β₁ × notification frequency + β₂ × GPS use + β₃ × app complexity + ε), with statistically significant P values (notification frequency with a P value of .01, GPS use with a P value of .05, and app complexity with a P value of .03), further quantified these bases\' effects on energy use.
CONCLUSIONS: The observed differences in the energy consumption of dietary apps reaffirm the need for a multidisciplinary approach to bring together app developers, end users, and health care experts to foster improved energy conservation practice while achieving a balance between sustainable practice and user experience. More research is needed to better understand how to scale-up consumer engagement to achieve sustainable development goal 12 on responsible consumption and production.

This study investigated the effect of low-intensity pulsed electric field (PEF) (0.3-0.7 kV/cm) and/or germination (0-72 h, 20 °C) on faba beans prior to flour- and breadmaking. PEF (0.5 and 0.7 kV/cm) had no significant effect on the germination performance of faba bean but had a positive effect on in vitro starch and protein hydrolysis of PEF-treated beans germinated for 72 h. The incorporation of flour from soaked, germinated, PEF-treated, and PEF-treated+germinated faba beans into wheat bread, at 30% mass level, improved the nutritional composition (total starch and protein contents) and protein digestibility but it reduced the specific volume and increased the density, brownness, and hardness of the bread. This finding shows for the first time that PEF-treatment (<0.7 kV/cm) of faba beans followed by germination (72 h) improved in vitro starch and protein hydrolysis of its flour and the protein digestibility at gastric phase of its enriched wheat bread.

In this study, a photovoltaic/thermal (PVT) collector and a stepped solar still system were constructed and integrated. The PVT collector was used to improve the performance of a stepped solar still device. Saltwater enters into the PV-T system and the temperature of the solar panel declines, and then ultimately the efficiency of the PV-T collector increases. After leaving the PVT collector, the temperature of the saltwater increased and was used as a pre-heater for further evaporation in the solar still, which ultimately caused an increase in its efficiency. The more tremendous temperature difference generated between the stepped surface and the glass increases efficiency and produces more freshwater. A flow rate of 7.5 L/hour of saline water was used to study the efficiency of the solar still device and the PVT collector. The value of productivity of solar still system with photovoltaic/thermal collector was 0.76 kg/m2 more than that of conventional solar still. Despite the PVT collector, the daily efficiency of the solar still system increased to 34.8%, which shows an increase of 13.9% compared to the passive solar still device. Also, by cooling the PV-T system, the average electrical efficiency has increased from 13.1 to 13.7%. Production power reached 72.46 W from 65.96 W in two consecutive days at 11:15.

This study quantifies the financial and environmental impacts of a microalgal bioenergy system that attempts to maximize circular flows by recovering and reusing the carbon, nutrients, and water within the system. The system produces microalgal biomass using liquid digestate of an anaerobic digester that processes 45 metric tons of food waste and generates 28.6 m3 of permeate daily in California, and three energy production scenarios from the biomass are considered: producing biodiesel, electricity, and both. In all scenarios, the resulting energy products delivered only modest reductions in environmental impacts as measured by carbon dioxide equivalent emissions. The carbon intensities (CIs) of biodiesel from this study were 91.0 gCO2e/MJ and 93.3 gCO2e/MJ, which were lower than 94.71 gCO2e/MJ of conventional petroleum diesel, and the CI of electricity from this study was 70.6 gCO2e/MJ, lower than the average electricity grid CI in California (82.92 gCO2e/MJ). The economic analysis results show that generating electricity alone can be profitable, while biodiesel produced via this system is not cost competitive with conventional diesel due to high capital expenses. Thus, generating electricity in lieu of biodiesel appears to be a better option to maximize the use of waste flows and supply lower-carbon energy.

OBJECTIVE: Identify workplace risk factors for SARS-CoV-2 infection, using data collected by a UK electricity-generating company.
METHODS: Using a test-negative design case-control study, we estimated the OR of infection by job category, site, test reason, sex, vaccination status, vulnerability, site outage and site COVID-19 weekly risk rating, adjusting for age, test date and test type.
RESULTS: From an original 80 077 COVID-19 tests, there were 70 646 included in the final analysis. Most exclusions were due to being visitor tests (5030) or tests after an individual first tested positive (2968).Women were less likely to test positive than men (OR=0.71; 95% CI 0.58 to 0.86). Test reason was strongly associated with positivity and although not a cause of infection itself, due to differing test regimes by area, it was a strong confounder for other variables. Compared with routine tests, tests due to symptoms were highest risk (94.99; 78.29 to 115.24), followed by close contact (16.73; 13.80 to 20.29) and broader-defined work contact 2.66 (1.99 to 3.56). After adjustment, we found little difference in risk by job category, but some differences by site with three sites showing substantially lower risks, and one site showing higher risks in the final model.
CONCLUSIONS: In general, infection risk was not associated with job category. Vulnerable individuals were at slightly lower risk, tests during outages were higher risk, vaccination showed no evidence of an effect on testing positive, and site COVID-19 risk rating did not show an ordered trend in positivity rates.

During surgery, the use of a high-frequency electric knife produces smoke, which can be harmful to the health of indoor medical staff and patients. The quantity and particle size distribution of smoke particles produced by different tissues may vary. Understanding the release characteristics of these smoke particles is necessary to clarify their impact on the surgical environment and to seek effective smoke control methods. A previous comparative analysis of human and pig tissues revealed that they share similar water and fat compositions in certain anatomical regions. In this study, we investigated the emission characteristics of smoke particles from various tissues of pigs (skeletal muscle, liver, kidney, skin, and subcutaneous fat) under different operating powers of an electric knife. We measured the indoor particle number concentration (particle concentration), and estimated the PM2.5 mass concentration (PM2.5 concentration), particle size distribution, and emission rate of the smoke particles. The study obtained the particle emission rates of different tissues under different electric knife operating powers, results of which showed that (1) during the operation of the electric knife, mainly small particles below 1 μm are produced. Among them, particles of 0.3 μm were the most abundant, with a particle concentration level of up to 109 particles/m3, accounting for 85.17-97.64% of the total particle number, and as the particle size increased, the particle concentration and percentage decreased significantly. (2) The water and fat compositions of different tissues influenced the indoor particle concentration and emission rate of the smoke emitted by the electric knife. Among different tissues, subcutaneous fat tissue had the lowest particle concentration and emission rate. (3) The electric knife operating power mainly affected particles below 1 μm, and except for kidney tissue, the indoor concentration and emission rate of these particle sizes were positively correlated with the power. The experimental results can provide data reference for the use of high-frequency electric knives in surgeries involving different human tissues in the operating room.

The treatment of slaughterhouse wastewater is a complex task demanding careful consideration due to its challenging nature. Therefore, exploring more sustainable treatment methods for this particular type of wastewater is of utmost significance. This research focused on the impact of electrode materials, specifically graphite and titanium, on the efficiency of microbial fuel cells (MFCs) and electro-Fenton systems in treating slaughterhouse wastewater. Both graphite and titanium electrodes displayed increasing current density trends, with titanium outperforming graphite. Titanium showed superior electron transfer and current generation (2.2 to 21.2 mA/m2 ), while graphite ranged from 2.4 to 18.9 mA/m2 . Titanium consistently exhibited higher power density, indicating better efficiency in converting current to power (0.059 to 22.68 mW/m2 ), compared to graphite (0.059 to 12.25 mW/m2 ) over the 48-h period. In removal efficiency within the MFC system alone, titanium exhibited superior performance over graphite in key parameters, including zinc (45.5% vs. 37.19%), total hardness (39.32% vs. 29.4%), and nitrates (66.87% vs. 55.8%). For the electro-Fenton system with a graphite electrode, the removal efficiency ranged from 34.1% to 87.5%, with an average efficiency of approximately 56.2%. This variability underscores fluctuations in the efficacy of the graphite electrode across diverse wastewater treatment scenarios. On the other hand, the electro-Fenton system employing a titanium electrode showed removal efficiency values ranging from 26.53% to 89.99%, with an average efficiency of about 68.4%. The titanium electrode exhibits both a comparatively higher and more consistent removal efficiency across the evaluated scenarios. On the other hand, the integrated system achieved more than 90% removal efficiency from most of the parameters. The study underscores the intricate nature of slaughterhouse wastewater treatment, emphasizing the need for sustainable approaches. PRACTITIONER POINTS: Microbial fuel cell (MFC) and electro-Fenton were investigated for slaughterhouse wastewater treatment. The MFC microbial activity started to decrease after 24 h. The integrated system achieved up to 99.8% removal efficiency (RE) for total coliform bacteria. Up to 99.4% of RE was also achieved for total suspended solids (TSS). The integrated system highly improved RE of the pollutants.

暂无摘要。