Molecular transport processes in printed polymer droplets hold enormous importance for understanding wetting phenomena and designing systems in applications such as encoding, electronics, photonics, and sensing. This paper studies thickness-dependent dewetting modes that are activated by thermal annealing and driven by interfacial interactions within microscopically confined polymeric features. The printing of poly(2-vinylpyridine) is performed in a regime where coffee-ring effects lead to strong thinning of the central region of the deposit. Thermal annealing leads to two different modes of dewetting that depend on the thickness of the central region. Mode I refers to the formation of randomly positioned small features surrounded by large hemispherical ones located along the periphery of the printed features and occurs when the central regions are thin. Observed at large central thicknesses, Mode II mediates significant molecular transport from edges toward the center of the printed droplet with thermal annealing and forms a hemispherical feature from the initial ring-like deposit. The selective adsorption of red, green, and blue emitting quantum dots over the poly(2-vinylpyridine) results in photoluminescent patterns. The selective assembly of photoluminescent quantum dots over patterned surfaces leads to deterministic and stochastic features beneficial to creating security labels for anti-counterfeiting applications.

UNASSIGNED: 3D-printing is a rapidly developing technology with applications in orthopaedics including pre-operative planning, intraoperative guides, design of patient specific instruments and prosthetics, and education. Existing literature demonstrates that in the surgical treatment of a wide range of orthopaedic pathology, using 3D printing shows favourable outcomes. Despite this evidence 3D printing is not routinely used in orthopaedic practice. We aim to evaluate the advantages of 3D printing in orthopaedic surgery to demonstrate its widespread applications throughout the field.
UNASSIGNED: We performed a comprehensive systematic review and meta-analysis. AMED, EMBASE, EMCARE, HMIC, PsycINFO, PubMed, BNI, CINAHL and Medline databases were searched using Healthcare Databases Advanced Search (HDAS) platform. The search was conducted to include papers published before 8th November 2020. Clinical trials, journal articles, Randomised Control Trials and Case Series were included across any area of orthopaedic surgery. The primary outcomes measured were operation time, blood loss, fluoroscopy time, bone fusion time and length of hospital stay.
UNASSIGNED: A total of 65 studies met the inclusion criteria and were reviewed, and 15 were suitable for the meta-analysis, producing a data set of 609 patients. The use of 3D printing in any of its recognised applications across orthopaedic surgery showed an overall reduction in operative time (SMD = -1.30; 95%CI: -1.73, -0.87), reduction in intraoperative blood loss (SMD = -1.58; 95%CI: -2.16, -1.00) and reduction in intraoperative fluoroscopy time (SMD = -1.86; 95%CI: -2.60, -1.12). There was no significant difference in length of hospital stay or in bone fusion time post-operatively.
UNASSIGNED: The use of 3D printing in orthopaedics leads to an improvement in primary outcome measures showing reduced operative time, intraoperative blood loss and number of times fluoroscopy is used. With its wide-reaching applications and as the technology improves, 3D printing could become a valuable addition to an orthopaedic surgeon\'s toolbox.

Single-cell analysis by mass spectrometry (MS) is emerging as a powerful tool that not only contributes to cellular heterogeneity but also offers an unprecedented opportunity to predict pathology onset and facilitates novel biomarker discovery. However, the development of single-cell MS analysis techniques with a focus on sample extraction, separation, and ionization methods for volume-limited samples and complexity of cellular samples are still a big challenge. In this study, we present a high-throughput approach to inkjet drop on demand printing single-cell MS for rapid screening of biomarkers of polycyclic aromatic hydrocarbon (PAH) exposure at the KYSE-150 cell, aiming to elucidate the pathogenesis of PAH-induced esophageal cancer. With an analytical bulk KYSE-150 cell throughput of up to 51 cells per minute, the method provides a new opportunity for simultaneous single-cell analysis of multiple biomarkers. We screened 930 characteristic ions from 3,683 detected peak signals and identified 91 distinctive molecules that exhibited significant differences under various concentrations of PAH exposure. These molecules have potential as clinical diagnostic biomarkers. Additionally, the current study identifies specific biomarkers that behave completely opposite in single-cell and multicell lipidomics as the concentration of PAH changes. These biomarkers potentially subdivide KYSE-150 cells into PAH-sensitive and PAH-insensitive types, providing a basis for revealing PAH toxicity and disease pathogenesis from the heterogeneity of cellular metabolism.

OBJECTIVE: External ear reconstruction has been a challenging subject for plastic surgeons for decades. Popular methods using autologous costal cartilage or polyethylene still have their drawbacks. With the advance of three-dimensional (3D) printing technique, bioscaffold engineering using synthetic polymer draws attention as an alternative. This is a clinical trial of ear reconstruction using 3D printed scaffold, presented with clinical results after 1 year.
METHODS: From 2021 to 2022, five adult patients with unilateral microtia underwent two-staged total ear reconstruction using 3D printed implants. For each patient, a patient-specific 3D printed scaffold was designed and produced with polycaprolactone (PCL) based on computed tomography images, using fused deposition modeling. Computed tomography scan was obtained preoperatively, within 2 weeks following the surgery and after 1 year, to compare the volume of the normal side and the reconstructed ear. At 1-year visit, clinical photo was taken for scoring by two surgeons and patients themselves.
RESULTS: All five patients had completely healed reconstructed ear at 1-year follow-up. On average, the volume of reconstructed ear was 161.54% of that of the normal side ear. In a range of 0 to 10, objective assessors gave scores 3 to 6, whereas patients gave scores 8 to 10.
CONCLUSIONS: External ear reconstruction using 3D printed PCL implant showed durable, safe results reflected by excellent volume restoration and patient satisfaction at 1 year postoperatively. Further clinical follow-up with more cases and refinement of scaffold with advancing bioprinting technique is anticipated. The study\'s plan and results have been registered with the Clinical Research Information Service (CRIS No. 3-2019-0306) and the Ministry of Food and Drug Safety (MFDS No. 1182).

UNASSIGNED: To assess thickness variations of thermoformed and 3D-printed clear aligners.
UNASSIGNED: Six different thermoplastic materials with different initial thicknesses were used for aligner thermoforming using Biostar® device (Biostar®, SCHEU-DENTAL GmbH, Iserlohn, Germany). Also, two different dental resins were used to create the printed aligners in three digitally designed thicknesses using IZZI Direct printer (3Dtech, Zagreb, Croatia). The aligners were measured using an electronic micrometer (ELECTRONIC UNIVERSAL MICROMETER, Schut Geometrical Metrology, Groningen, The Netherlands, accuracy: 0.001 mm) on a total of 20 points per aligner. Statistical analysis was performed using the JASP program (JASP, University of Amsterdam, Amsterdam, The Netherlands).
UNASSIGNED: The difference between the thermoformed and printed groups was statistically significant. Significant differences between different thermoformed materials and between 3D-printed materials were found. The thickness of thermoformed aligners deviated more in the upper jaw, whereas the thickness of printed aligners deviated more in the lower jaw. Both differences were statistically significant. The greatest average deviation from the initial thickness was found in Duran 0.75; Erkodur 0.6; Erkoloc-Pro 1.0; IZZI 0.5; NextDent 0.6 and NextDent A 0.6. NextDent group had the lowest deviations for all teeth of both jaws, except for upper and lower first molar where NextDent A group was more accurate.
UNASSIGNED: Thermoformed aligners showed decreased values, while printed ones showed mostly increased values compared to the original material thickness. The highest mean deviation belonged to IZZI group, and the NextDent group had the lowest mean deviation. The thickness of both aligners was thinner at the edges compared to the thickness at cusps and fissures.

In recent years, consumer preferences have begun to turn back to natural dyes, whereas synthetic dyes have been pushed into the background over the previous 60 years. This is a result of increased knowledge of the potential hazards associated with the creation of synthetic dyes, which use raw materials derived from petrochemicals and involve intense chemical interactions. Such dyes need a lot of energy to produce, and their negative effects on the environment increase pollution. It has been discovered that several of these dyes, particularly the azo-based ones are carcinogenic. On the contrary, natural dyes are getting more attention from scientists and researchers as a result of their several advantages like being eco-friendly, biodegradable and renewable, sustainable, available in nature, having no disposal problems, minimizing the consumption of fossil fuel, anti-bacterial, insect repellent, and anti-allergic, anti-ultraviolet, intensify dyeing and finishing process efficiency, less expensive, and no adverse effects on human health and environment. However, there are also some drawbacks, like poor fastness properties, natural dye printing for bulk production, difficulties in reproducibility of shades, and so forth. Despite all these limitations, the demand for natural dyes is increasing significantly in textile industries because they offer far more safety than synthetic dyes. This study provides an overall concept of the natural dyes in textile printing. It illustrates parameters of printing performance, methods, and techniques of extraction of natural dyes, printing methods, and printing of natural and synthetic fibers. Finally, this study describes the challenges and future prospects of natural dyes in textile printing.

BACKGROUND: Precise localized printing of plasmonic nanoparticles at desired locations can find a plethora of applications in diverse areas, including nanophotonics, nanomedicine, and microelectronics. The focused laser beam-assisted optical printing technique has illustrated its potential for the localized printing of differently shaped plasmonic particles. However, the technique is either time-consuming or often requires focused optical radiation, limiting its practical applications. While the optothermal printing technique has recently emerged as a promising technique for the direct and rapid printing of plasmonic nanoparticles onto transparent substrates at lower laser intensities, its potential to print the plasmonic nanoparticles to the core of the optical fiber platforms and utilize it for biological cell trapping as well as an analytical platform remains unexplored.
RESULTS: Herein, we demonstrate the thermal-convection-assisted printing of the Ag plasmonic nanoparticles from the plasmonic colloidal solution onto the core of single-mode optical fiber and its multi-functional applications. The direct printing of plasmonic structure on the fiber core via the thermal-convection mechanism is devoid of the requirement of any additional chemical ligand to the fiber core. Further, we demonstrated the potential of the developed plasmonic fiber probe as a multifunctional surface-enhanced Raman spectroscopic (SERS) platform for sensing, chemical reaction monitoring, and single-cell studies. The developed SERS fiber probe is found to detect crystal violet in an aqueous solution as low as 100 pM, with a plasmonic enhancement of 107. Additionally, the capability of the fiber-tip platform to monitor the surface plasmon-driven chemical reaction of 4-nitrothiophenol (4NTP) dimerizing into p, p\'-dimercaptoazobenzene (DMAB) is demonstrated. Further, the versatility of the fiber probe as an effective platform for opto-thermophoretic trapping of single biological cells such as yeast, along with its Raman spectroscopic studies, is also shown here.
CONCLUSIONS: In this study, we illustrate for the first time the optothermal direct printing of plasmonic nanoparticles onto the core of a single-mode fiber. Further, the study demonstrates that such plasmonic nanoparticle printed fiber tip can act as a multi-functional analytical platform for optothermally trap biological particles as well as monitoring plasmon-driven chemical reactions. In addition, the plasmonic fiber tip can be used as a cost-effective SERS analytical platform and is thus expected to find applications in diverse areas.

4D printing is an innovative digital manufacturing technology that originated by adding a fourth dimension, i.e., time, to pre-existing 3D technology or additive manufacturing (AM). AM is a fast-growing technology used in many fields, which develops accurate 3D objects based on models designed by computers. Dentistry is one such field in which 3D technology is used for manufacturing objects in periodontics (scaffolds, local drug-delivering agents, augmentation of ridges), implants, prosthodontics (partial and complete dentures, obturators), oral surgery for reconstructing jaw, and orthodontics. Dynamism is a vital property needed for the survival of materials used in the oral cavity since the oral cavity is constantly subjected to various insults. 4D printing technology has overcome the disadvantages of 3D printing technology, i.e., it cannot create dynamic objects. Therefore, constant knowledge of 4D technology is required. 3D printing technology has shortcomings, which are discussed in this review. This review summaries various printing technologies, materials used, stimuli, and potential applications of 4D technology in dentistry.

OBJECTIVE: In oral rehabilitation, a full mouth minimal invasive treatment can represent a major challenge for the patient and the dentist. The purpose of this article is to present a new technique to restore eroded teeth and recover the vertical dimension with a simple and predictable technique.
METHODS: Occlusal tabletop restorations are a suitable conservative option to restore anatomy and vertical dimension augmentation but highly sensitive. The cementation of those restorations without stable landmarks, the cement excess removal, the insertion path, or the time needed are some of the difficulties can be faced. Now a days with the new CAD-CAM techniques is possible to develop a new occlusal tabletop manufacturing alternative utilizing 3D-printed technology by unifying the restorations with a customized connector that allows us to print several onlays at same time, as a single object, also being cemented at once.
CONCLUSIONS: This protocol reduces the technique sensitivity of a vertical dimension oral rehabilitation process, reduce the chair time, enhancing the patient-comfort and delivers a unique way to restore dental lost anatomy as a definitive or temporary way with printing materials.
CONCLUSIONS: With the advent of new CAD-CAM 3D printing materials, which are increasingly versatile and gaining favor among clinicians, it is now possible to address complex clinical situations with greater predictability. This technology enables the development of treatment solutions that are both effective and efficient, consequently reducing clinical time for the patient.

In the present study, biosynthesized ZnO nanoparticles in food wastewater extract (FWEZnO NPs) was used in the photocatalytic degradation of real samples of printing ink wastewater. FWEZnO NPs were prepared using green synthesis methods using a composite food waste sample (2 kg) consisted of rice 30%, bread 20 %, fruits 10 %, chicken 10 %, lamb 10%, and vegetable 20%. The photocatalysis process was optimized using response surface methodology (RSM) as a function of time (15-180 min), pH 2-10 and FWEZnO NP (20-120 mg/100 mL), while the print ink effluent after each treatment process was evaluated using UV-Vis-spectrophotometer. The behaviour of printing ink wastewater samples for photocatalytic degradation and responses for independent factors were simulated using feed-forward neural network (FFNN). FWEZnO NPs having 62.48 % of the purity with size between 18 and 25 nm semicrystalline nature. The main functional groups were -CH, CH2, and -OH, while lipid, carbon-hydrogen stretching, and amino acids were the main component in FWEZnO NP, which contributed to the adsorption of ink in the initial stage of photocatalysis. The optimal conditions for printing ink wastewater were recorded after 17 min, at pH 9 and with 20 mg/100 mL of FWEZnO NPs, at which the decolorization was 85.62 vs. 82.13% of the predicted and actual results, respectively, with R2 of 0.7777. The most significant factor in the photocatalytic degradation was time and FWEZnO NPs. The FFNN models revealed that FWEZnO NPs exhibit consistency in the next generation of data (large-scale application) with an low errors (R2 0.8693 with accuracy of 82.89%). The findings showing a small amount of catalyst is needed for effective breakdown of dyes in real samples of printing ink wastewater.