Starches-rich and protein-rich cereal samples commonly need tedious sample preparation steps before instrumental analysis. This study developed a miniaturized centrifugal integrated cold-induced phase separation (CIPS) method for convenient sample preparation. A small-sized centrifuge tube (2 mL) and a low-temperature centrifuge, both of which are easily accessible, make up the basic components of the system. Unlike conventional sample preparation methods that need a step-by-step extraction, enrichment, purification, and centrifugation, this centrifugal integrated CIPS method can be performed by a one-step combination protocol under a low-temperature centrifuge. As a proof-of-concept study, satisfactory recoveries and enrichment factors were demonstrated for the extraction of fumonisins and ochratoxins from cereals. A sensitive and selective quantification method was yielded by combining LC-HRMS using tSIM acquisition mode, with good linearity (R2 > 0.998), accuracy (82.9-106.5%), and precision (<13.4%). This strategy is convenient, low-cost, repeatable, and easy to semi-automate, further expanding the extraction potential for other acidic mycotoxins.

Biodiesel production processes, such as gravity settling, have limitations in terms of biodiesel yield, purification efficiency, operating time in the separation process, and more extensive equipment. Therefore, this study has focused on using a recently developed centrifuge machine for biodiesel separation to address these challenges due to its compact design, high efficiency, and simplicity. Additionally, this study aimed to optimize the separation efficiency of glycerol from biodiesel using a centrifuge machine, employing response surface methodology (RSM) with central composite design (CCD). The optimum conditions for separating glycerol from biodiesel via centrifuge machine are a rotation speed of 1800 rpm, a mixture flow rate of 192.25 ml/min, and a temperature of 55 °C, respectively. In optimum conditions, 94.52% separation efficiency was achieved. Biodiesel production can be improved, leading to higher yields and greater purity. The utilization of RSM proved valuable in determining the optimum conditions for separation. Furthermore, the machine successfully separated the biodiesel to meet ASTM D6751 and EN 14,214 standards. The results highlight the potential of the centrifuge machine for efficient and reliable biodiesel production, contributing to the advancement of the biodiesel industry.

OBJECTIVE: The aim of the study was to assess lameness in dogs with advanced osteoarthritis of the hip and knee joints after a single autologous point-of-care transplantation of the Stromal Vascular Fraction (SVF) into the affected joint.
METHODS: During a minilaparotomy, 10 g of falciform fat was removed from each patient for each joint to be treated. A modern and time-saving procedure (ARC TM System, InGeneron GmbH, Houston, USA) was used for the in-house preparation of the SVF, so that the isolated cells could be applied to the respective joint within 2 h after fat removal. In total, five knee joints of five patients and seven hip joints of four patients were treated.
RESULTS: Improvement in lameness according to owner questionnaires was seen in 3 of 5 patients with knee joint arthritis and 2 of 4 patients with hip joint arthritis. Based on gait analysis, only one dog with gonarthrosis and one dog with coxarthrosis showed improvement up to a maximum of 3 months after surgery.
CONCLUSIONS: This is the first case series on the treatment of osteoarthrosis of the knee or hip joint using point-of-care transplantation of the SVF. In individual cases, this method may represent a therapeutic approach for the treatment in dogs with advanced cox- or gonarthrosis, although only a short-term effect can be expected, which calls into question the effort and costs involved.

Safflower oil is a very valuable product for the body and human health. It is rich in macro- and microelements, vitamins and minerals, and also has antioxidant properties. The primary purification of safflower oil is an important stage of its production and directly affects the quality of the final product and its storage ability. Purifying safflower oil using a combination of filtration and sedimentation processes in an experimental cone-shaped centrifuge is a new direction in its processing. The purpose of this study was to determine the effects of flax fiber as a filter material for safflower oil. The Akmai variety of the safflower was tested. The results showed that the quality indicators of safflower oil before and after filtration through flax fiber are different. The amount of unsaturated fatty acids such as oleic (18.31 ± 0.874%) and cis-linoleic acid (82.52 ± 1.854%) increased, as well as the content of arginine (2.1), tyrosine (0.57), methionine (0.4), cystine (2.5), tryptophan (2.6), and other amino acids (in oil g per 100 g of protein). The increase in the total amount of phenols (322.12 ± 6 mgEAG/kg of oil) was observed, which directly caused the higher antioxidant activity (42.65 ± 8%) of the safflower oil. These results demonstrate that flax fiber can enrich safflower oil. To find the optimal conditions for safflower oil centrifugation in a cone-shaped sedimentary-filtering centrifuge, the thickness of the flax fiber and the distance between the inner and outer perforated filter rotor were tested. It was found that the optimal and effective thickness of the flax fiber is 1.5 × 107 nm, while the thickness of the sediment is 0.5 × 107 nm.

UNASSIGNED: This work reports the duration, safety, and viability of intravitreal slurry triamcinolone acetonide (TA; 1.0 mL of 40-mg/mL TA centrifuge concentrated into a 0.1-mL pellet) to treat cystoid macular edema (CME).
UNASSIGNED: A retrospective, consecutive review was conducted of patients undergoing intravitreal slurry TA injections, July 2009 to December 2018.
UNASSIGNED: In 143 eyes of 120 patients, slurry TA resolved CME for a mean of 327.15 (SD = 213.11) days, or 10.76 (SD = 7.00) months, per intravitreal injection (n = 466). In 100 eyes requiring multiple injections (n = 423), mean duration was 270.95 (SD = 177.14) days, or 8.91 (SD = 5.82) months, between injections. In 43 single-injection eyes, duration was 749.30 (SD = 483.17) days, or 24.63 (SD = 15.88) months. Mean duration decreased from 337.89 (SD = 210.46) days, or 11.11 (SD = 6.92) months, in nonvitrectomized eyes to 279.74 (SD 179.63) days, or 9.20 (SD = 5.91) months, in vitrectomized eyes (n = 74 injections, t = 2.24, P = .014, 1-tailed). Central foveal thickness as shown on optical coherence tomography decreased by 173.89μ (SD = 147.56μ), from 459.16μ (SD = 47.14μ) to 285.27μ (SD = 77.27μ; t = -25.31, P < .001), within 43.41 days (SD = 36.86). Visual acuity improved from 20/100 (logMAR 0.70, SD = 0.33) to 20/74 (logMAR 0.57, SD = 0.31; SD = 0.21; t = -11.01, P < .001), within 33.98 (SD 24.98) days. Fifteen of 31 phakic eyes (48.39%) underwent cataract extraction. Fifty-seven eyes (39.86%) developed a steroid response (> 10 mm Hg increase from baseline) 94.79 days (SD = 85.52 days), or 3.11 (SD = 2.81) months, following injection.
UNASSIGNED: A single injection of slurry TA lasted on average 10.76 months with significant improvement of CME and visual acuity. Adverse ocular effects were comparable to currently available, long-term, implantable steroids. Slurry TA appears to be an easily reproducible, safe, and cost-effective alternative to long-term intraocular steroid delivery.

Platelet-rich plasma (PRP), an inexpensive yet powerful treatment modality, is widely used but poorly understood. Three areas of unmet need are the ability to compare results using differing centrifuges and methods; translating a study result into a specific practice; and estimating yield and dosage without the benefit of an in-office hematology analyzer. PRPCalc2 is a set of software tools that facilitates these goals. The app consists of software tools that (1) calculate the appropriate radius for centrifugation, (2) calculate the correct revolutions per minute (RPM) for the centrifuge, (3) calculate the mean yield for the method and its confidence interval, and (4) calculate platelet dosage. Using these tools, a practitioner with any centrifuge can create and validate their own PRP preparation method and then use it to create a standardized PRP.

Calcium carbonate induced by microorganisms can quickly fill and cement sand particles, thereby effectively reducing the potential for the liquefaction of sand. This process could represent a new green approach to the liquefaction treatment of saturated sand and has good prospects for application. However, owing to the diversity of microbial activities and the heterogenous spatiotemporal distribution of bacterial nutrient seepage in sandy soil foundations, the resultant complex distribution of calcium carbonate deposition in a sandy soil foundation can lead to differences in solidification strength and improvement effect. To understand the influence of earthquake action on the liquefaction resistance of saturated sand treated by microorganisms, and to evaluate the effect of microbial technology on sand liquefaction prevention under dynamic load, this study simulated the dynamic stress conditions of saturated sand under shear waves, using the world\'s first centrifuge shaking table (R500B), which realizes horizontal and vertical two-way vibration. On the basis of spatial heterogeneity of microbial mineralization after centrifuge shaking table tests, the effect of microbial strengthening on liquefied sand was analyzed, and the spatial distribution of calcium carbonate mineralization was examined. The results showed that the distribution of microorganisms in the solidified soil exhibited obvious spatial heterogeneity with a significant edge effect. Although microbial mineralization effectively improved the liquefaction resistance of saturated sand, a sudden change in the process of calcium carbonate deposition altered the cementation of the sand with depth. Moreover, the curing strength had obvious complexity and uncertainty that directly affected the shear stiffness of the soil under dynamic load, and this constitutes one of the reasons for the degradation of shear stiffness of sand during liquefaction. The derived conclusions could be used as a reference for engineering applications of microbial treatment of a liquefiable sandy soil foundation.

The aim of this manuscript is to provide all the necessary information to build a simple benchtop mini centrifuge that is able to remove droplets and liquid film from the inner wall of PCR tubes and PCR strips following vortexing. Users can choose between two rotors: one can hold up to six tubes (1.5/2 ml, or 500 µl and 200 µl tubes with adapters) or two PCR strips. The design consists of only three printed parts (optimized to be printed without supports) and cheap off-the-shelf components (80 mm computer fan, switches, food container and power supply). It can be assembled with basic soldering skills, no programming needed. While the total cost of materials is only 20 €, when compared to its commercial counterparts, this DIY benchtop spinner was equally capable to remove droplets. Comparing noise levels this model was quieter than an Eppendorf 5424, BioSan MSC-6000 or Kisker biotech centrifuges. Because it is designed to perform a very generic and common task, it could be useful for a very wide array of laboratories and researchers: molecular biology, genetics, microbiology, student labs, biohacking labs, etc.

This work tests the reliability of a simple, rapid centrifugal technique to estimate the removal force necessary to detach common airborne particles from the surface of a photovoltaic panel. Previously, we have used atomic force microscopy (AFM) to obtain the surface-particle adhesion force for different pollutant types that generally contribute to panel soiling. To overcome the limitations of AFM, the same particles were studied as a population using an ultracentrifuge. Detachment was quantified at speeds between 1000 and 10,000 rpm, both as individual particle counts and as projected surface area coverage. The force of centrifugal detachment for each particle type followed a similar trend as the adhesion force given by AFM. Organic and carbon-based materials needed higher centrifugal speeds to be removed, suggesting a stronger attachment to the surface. However, the technique also highlighted the importance of particle diameter, aggregates, and individual particle characteristics, which should be considered when predicting the probability of detachment. We have identified the relationship between AFM-derived adhesion and centrifugal detachment forces using model particle fractions of materials commonly found to soil solar panels, demonstrating the utility in using the more easily applied to centrifugal method to obtain information that can be calibrated to direct measurements of the force of particle attachment. This technique could be applied effectively in further studies on the influence of dust composition on long-term soiling and its reversibility.

Tsunami hazards have been observed to cause soil instability resulting in substantial damage to coastal infrastructure. Studying this problem is difficult owing to tsunamis\' transient, non-uniform and large loading characteristics. To create realistic tsunami conditions in a laboratory environment, we control the body force using a centrifuge facility. With an apparatus specifically designed to mimic tsunami inundation in a scaled-down model, we examine the effects of an embedded impermeable layer on soil instability: the impermeable layer represents a man-made pavement, a building foundation, a clay layer and alike. The results reveal that the effective vertical soil stress is substantially reduced at the underside of the impermeable layer. During the sudden runup flow, this instability is caused by a combination of temporal dislocation of soil grains and an increase in pore pressure under the impermeable layer. The instability during the drawdown phase is caused by the development of excess pore-pressure gradients, and the presence of the impermeable layer substantially enhances the pressure gradients leading to greater soil instability. The laboratory results demonstrate that the presence of an impermeable layer plays an important role in weakening the soil resistance under tsunami-like rapid runup and drawdown processes.