A promising method was established for the determination of nine halobenzoquinones (HBQs) in potable water by membrane solid-phase extraction (MSPE) pretreatment and the liquid chromatography-mass spectrometry (LC-MS) method. A 500 mL water sample was taken for enrichment by the SDB-RPS membrane, which was previously activated by methanol and ultrapure water. The sample was eluted with methanol and re-dissolved with the initial mobile phase after nitrogen blowing. Then, it was detected in negative ion mode using the working curve, and HBQs were quantified by the external standard method. The linearity was satisfactory in the concentration range of 4-1000 ng/L, with correlation coefficients of 0.9963~0.9994. The recoveries were 73.5~126.6% at three spiked levels, with relative standard deviations (RSDs) of 6.8~15.5%. The limits of detection (LOD, S/N = 3) values were 0.1~0.7 ng/L. The results demonstrate that the MSPE-LC-MS method is reliable, rapid, and sensitive for the simultaneous analysis of nine HBPs in potable water.

Water bottles for everyday usage are a typical addition to people\'s life and offer a practical way to stay hydrated. Even though safe and clean water is preferred for consumption, the water bottle or container used to drink water was never considered to be cleaned. Here, we examined the adhering microbial populations in water bottles composed of stainless steel (SS) and polyethylene terephthalate (PET). A total of 30 water bottles-15 PET and 15 SS-were gathered from different users. To identify and quantify the adhering microbial populations, microbial swabs from the inside surface of the bottles were collected and later cultivated on certain growth media. Overall the microbial load of PET is significantly higher than the SS water bottles of 68.8 + 19.1 cfu/ml and 35.4 + 8 cfu/ml respectively at initial sampling (P = 0.0027). We also evaluated the efficiency of various cleaning procedures in eliminating adherent bacteria populations. The cleaning strategy significantly reduced the microbial load (P<0.0001). The mean load observed was 11.2 + 2.3 cfu/ml post-wash. This comparison study offers important new information about the adherent microbial populations found in SS and PET water bottles used every day, in the end. This finding emphasizes the necessity of routine cleaning and upkeep of these bottles to reduce the possibility of microbial contamination and the accompanying health risks.

Legionella is an opportunistic waterborne pathogen that causes Legionnaires\' disease. It poses a significant public health risk, especially to vulnerable populations in health care facilities. It is ubiquitous in manufactured water systems and is transmitted via inhalation or aspiration of aerosols/water droplets generated from water fixtures (e.g., showers and hand basins). As such, the effective management of premise plumbing systems (building water systems) in health care facilities is essential for reducing the risk of Legionnaires\' disease. Chemical disinfection is a commonly used control method and chlorine-based disinfectants, including chlorine, chloramine, and chlorine dioxide, have been used for over a century. However, the effectiveness of these disinfectants in premise plumbing systems is affected by various interconnected factors that can make it challenging to maintain effective disinfection. This systematic literature review identifies all studies that have examined the factors impacting the efficacy and decay of chlorine-based disinfectant within premise plumbing systems. A total of 117 field and laboratory-based studies were identified and included in this review. A total of 20 studies directly compared the effectiveness of the different chlorine-based disinfectants. The findings from these studies ranked the typical effectiveness as follows: chloramine > chlorine dioxide > chlorine. A total of 26 factors were identified across 117 studies as influencing the efficacy and decay of disinfectants in premise plumbing systems. These factors were sorted into categories of operational factors that are changed by the operation of water devices and fixtures (such as stagnation, temperature, water velocity), evolving factors which are changed in-directly (such as disinfectant concentration, Legionella disinfectant resistance, Legionella growth, season, biofilm and microbe, protozoa, nitrification, total organic carbon(TOC), pH, dissolved oxygen(DO), hardness, ammonia, and sediment and pipe deposit) and stable factors that are not often changed(such as disinfectant type, pipe material, pipe size, pipe age, water recirculating, softener, corrosion inhibitor, automatic sensor tap, building floor, and construction activity). A factor-effect map of each of these factors and whether they have a positive or negative association with disinfection efficacy against Legionella in premise plumbing systems is presented. It was also found that evaluating the effectiveness of chlorine disinfection as a water risk management strategy is further complicated by varying disinfection resistance of Legionella species and the form of Legionella (culturable/viable but non culturable, free living/biofilm associated, intracellular replication within amoeba hosts). Future research is needed that utilises sensors and other approaches to measure these key factors (such as pH, temperature, stagnation, water age and disinfection residual) in real time throughout premise plumbing systems. This information will support the development of improved models to predict disinfection within premise plumbing systems. The findings from this study will inform the use of chlorine-based disinfection within premise plumbing systems to reduce the risk of Legionnaires disease.

Phenolic pollutants from industrial and agricultural activities pose a major threat to the world\'s potable water supply. The persistent micro-pollutants often find their way into drinking water sources with possible adverse human health implications. In this study, bottled water, tap water, and wastewater treatment plant (WWTP) effluent samples from the Boland region of the Western Cape, South Africa were assessed to determine 4-chlorophenol (4-CP) and 2,4-dichlorophenol (2,4-DCP) levels using HPLC/DAD instrumentation. The selected area is known for its vast agricultural ventures and wineries. Evaluation of the human health risk (cancer risk) for the pollutants was conducted using the hazard quotient (HQ). The Ames mutagenicity test was also conducted using the Salmonella typhimurium T98 and T100 strains and the S9 activation enzyme. Trace levels of the phenolics were detected in the samples with a range of 9.32 × 10-7-1.15 × 10-4 mg/L obtained for 4-CP, and 8.80 × 10-7-1.72 × 10-4 mg/L recorded for 2,4-DCP. Both compounds had levels below the limit of 0.01 mg/L prescribed by South African legislation. The assessed HQ for the phenolic concentrations indicates a low level of potential ecological risk and none of the samples had a cancer risk value that exceeded the regulatory limit. The possibility of the analyzed samples causing cancer is unlikely, but non-carcinogenic adverse effects were found. Strong mutagenicity was observed for the T98 strains with a potential ability to cause mutation toward the insertion or deletion of a nucleotide. The T100 bacterial strain showed very slight mutagenicity potential, however, it is unlikely to cause any mutation. The levels of phenolics in the potable water samples may pose a significant threat to human health. Hence, screening persistent organic chemicals in potable water sources and evaluating their potential human health effects is pertinent to prevent associated health challenges.

Nanoplastics are emerging environmental contaminants, but their presence in environmental and potable water remains largely understudied due to the absence of quantitative analytical methods. In this study, we developed and validated a pretreatment method that combines hydrogen peroxide digestion and Amicon® Stirred Cell ultrafiltration (at 100 kDa, approximately 10 nm) with subsequent detection by pyrolysis gas chromatography-mass spectrometry (Pyr-GC/MS). This method allows for the simultaneous identification and quantification of nine selected nanoplastic types, including poly(ethylene terephthalate) (PET), polyethylene (PE), polycarbonate (PC), polypropylene (PP), poly(methyl methacrylate) (PMMA), polystyrene (PS), polyvinylchloride (PVC), nylon 6, and nylon 66, in environmental and potable water samples based on polymer-specific mass concentration. Limits of quantification ranged from 0.01 to 0.44 µg/L, demonstrating the method\'s ability to quantitatively detect nanoplastics in environmental and potable water samples. Most of the selected nanoplastics were detected at concentrations of between 0.04 and 1.17 µg/L, except for PC, which was consistently below the limit of detection (<0.44 µg/L). The prevalent polymer components in the samples were PE (0.10 - 1.17 µg/L), PET (0.06 - 0.91 µg/L), PP (0.04 - 0.79 µg/L), and PS (0.06 - 0.53 µg/L) nanoplastics. The presented analytical method offers an accurate means to identify, quantify, and monitor nanoplastics in complex environmental and potable water samples. It fills gaps in our understanding of nanoplastic pollution levels, providing a valuable methodology and crucial reference data for future studies.

Polluted resources of potable water are daily used for different purposes in Lebanon. The optical microscopy is the traditional method used for the detection of Entamoeba spp. in water despite its weak sensitivity. We aimed to characterize domestic water at Nabatieh district, South Lebanon, and to develop a simple method for Entamoeba spp. detection. A total of 70 water samples were collected from houses and schools and analyzed for physical (pH, total dissolved solids and temperature), chemical (nitrate, phosphate and sulfate) and bacterial (total and fecal coliforms) parameters. The contamination by Entamoeba spp. was examined using microscopy, then a spectrophotometric wavelength scan was recorded for 50 samples in order to determine the common peak between positive samples. High phosphate levels were detected in all the samples, with important bacterial and parasitological contaminations. The spectrophotometric analyses showed a peak repetition at the wavelength of 696 nm in the spectrum of the majority of positive samples. The number of cysts was significantly correlated to optical densities at 696 nm (R = 0.9087; p-value<0.0001). The regression analysis showed that the OD696 could statistically predict the concentration (F (1,48) = 267.02, p-value <0.001). In conclusion, potable water parameters at Nabatieh district did not meet the national and international guidelines of safe drinking water, and the detection of Entamoeba spp. cysts in potable water can be performed using a rapid spectrophotometric analysis, by the determination of the optical density at 696 nm and the application of a specific equation.

Water is a fundamental requirement for the survival of human beings. Although water is abundantly available across the globe, access to freshwater still remains a major concern. Most of the water available is saline or brackish, which is not fit for human consumption. Desalination is the optimum solution for production of potable water from saline water. A major shortcoming of conventional desalination technologies is their dependence on fossil fuel that results in environmental degradation, global warming, etc. Therefore, sustainable desalination technology has evolved as a need of hour. Among all renewable energy resources, solar energy is abundantly available and can be potentially harvested. Therefore, solar energy can be used to drive sustainable desalination technologies. A solar still converts saline water into freshwater in a single step using solar energy. But the major drawbacks of solar still are relatively lower efficiency and lower yield. Nanofluids are widely used to overcome these limitations due to their extraordinary and unique properties. This paper critically reviews the recent research performed on the application of nanofluids in solar desalination systems. Methods of nanofluid preparation, their types and properties are also discussed in detail. Application of nanofluids in solar desalination systems is discussed with special attention on performance enhancement of solar stills. Combinations of nanofluids with various other performance enhancement techniques are also considered. The effectiveness of nanofluids in solar stills is found to be dependent majorly on the nature and concentration of the nanofluid used.

Rapid degradation of quality and quantity of the available limited fresh water reserves has forced nations around the globe to search for alternate fresh water sources. This has led to the development of various desalination technologies to generate potable water from abundantly available sea and brackish water. Desalination sector has undergone various upgradations to meet the rising fresh water demand in a sustainable way. One such upgradation is the utilization of solar energy as an energy source. High cost and associated environmental impacts with large-scale desalination systems have shifted the focus of researchers towards research and development of various small-scale efficient solar stills for cheap potable water production in rural, remote, arid, and coastal locations. In this review article, various configurations of a non-conventional solar still, namely inverted solar still, have been reviewed extensively by highlighting its classifications, design aspects, working principle, features, and economics. Moreover, the role of inverted solar still\'s evaporating and condensing surface characteristics and thermal properties on its distillate productivity has also been discussed. Inverted absorber multi-basin solar still and inverted multi-effect diffusion solar still configurations are highly productive. Economics of inverted solar still is better than other conventional solar still configurations and conventional reverse osmosis plant of few m3/day capacity. This review article will facilitate researchers to select appropriate inverted solar still configuration for further performance improvement and commercialization. The scope for future research works on inverted solar still has also been listed.

The Classic Maya (c. 250 to 900 CE) in the tropical southern lowlands of Central America dealt with water scarcity during annual dry seasons and periods of climate instability via sophisticated urban reservoir systems they relied on for over a thousand years. Surface water is limited because typically rain percolates through the karstic terrain. I posit that Maya reservoirs functioned as do constructed wetlands (CWs) at present. Still-water systems like CWs and Maya reservoirs can become stagnant and nonpotable due to the build-up of nutrients that promote algal growth. Stagnant waters also serve as breeding grounds for mosquitoes that spread endemic diseases. CWs keep water clean via certain aquatic plants since all plants uptake nutrients (e.g., nitrogen, phosphorus) and decomposing plant matter supports microbial biofilms that break down nutrients. CWs also support diverse zooplankton that prey on pathogens and bacteria that assist to denitrify water. CWs do not require the use of chemicals or fossil fuels and after the initial labor-intensive output become self-cleaning and self-sufficient with some maintenance. I posit that the Maya used a diverse array of aquatic plants and other biota to keep water clean in the same manner as do CWs, which I demonstrate using evidence from excavations and settlement maps, sediment cores and current wetlands, and the iconographic and hieroglyphic records. The next step is to combine what we know about ancient Maya reservoirs in conjunction with what is currently known about CWs to better address future water needs.

A microbial fuel cell (MFC) biosensor with an anode as a sensing element is often unreliable at low or significantly fluctuating organic matter concentrations. To remove this limitation, this work demonstrates capillary action-aided carbon source delivery to an anode-sensing MFC biosensor for use in carbon-depleted environments, e.g., potable water. First, different carbon source delivery configurations using several thread types, silk, nylon, cotton, and polyester, are evaluated. Silk thread was determined to be the most suitable material for passive delivery of a 40 g L-1 acetate solution. This carbon source delivery system was then incorporated into the design of an MFC biosensor for real-time detection of toxicity spikes in tap water, providing an organic matter concentration of 56 ± 15 mg L-1. The biosensor was subsequently able to detect spikes of toxicants such as chlorine, formaldehyde, mercury, and cyanobacterial microcystins. The 16S sequencing results demonstrated the proliferation of Desulfatirhabdium (10.7% of the total population), Pelobacter (10.3%), and Geobacter (10.2%) genera. Overall, this work shows that the proposed approach can be used to achieve real-time toxicant detection by MFC biosensors in carbon-depleted environments.