Water treatment has turned out to be more important in most societies due to the expansion of most economies and to advancement of industrialization. Developing efficient materials and technologies for water treatment is of high interest. Thin film nanocomposite membranes are regarded as the most effective membranes available for salts, hydrocarbon, and environmental pollutants removal. These membranes improve productivity while using less energy than conventional asymmetric membranes. Here, the polyvinylidene fluoride (PVDF) membranes have been successfully modified via dip single-step coating by silica-aminopropyl triethoxysilane/trimesic acid/melamine nanocomposite (Si-APTES-TA-MM). The developed membranes were evaluated for separating the emulsified oil/water mixture, the surface wettability of the membrane materials is therefore essential. During the conditioning step, that is when the freshwater was introduced, the prepared membrane reached a flux of about 27.77 L m-2 h-1. However, when the contaminated water was introduced, the flux reached 18 L m-2 h-1, alongside an applied pressure of 400 kPa. Interestingly, during the first 8 h of the filtration test, the membrane showed 90 % rejection for ions including Mg2+, and SO42- and ≈100 % for organic pollutants including pentane, isooctane, toluene, and hexadecane. Also, the membrane showed 98 % rejection for heavy metals including strontium, lead, and cobalt ions. As per the results, the membrane could be recommended as a promising candidate to be used for a mixture of salt ions, hydrocarbons, and mixtures of heavy metals from wastewater.

Hypertension is a common cause of cardiovascular diseases, closely associated with the high mortality and disability rates of cardiovascular diseases such as stroke and coronary heart disease. Therefore, developing a comfortable and sustainable device for monitoring human pulse signals holds practical significance for the prevention and treatment of hypertension and cardiovascular diseases. PVDF flexible pressure sensors possess the characteristics of high sensitivity, good flexibility, and strong biocompatibility, thereby demonstrating extensive application potential in areas such as health monitoring, wearable devices, and electronic skins. This paper focuses on the development of a modified piezoelectric polymer and its application in an intelligent blood pressure monitoring system, demonstrating its outstanding performance and feasibility through a series of experiments. This research provides innovative material choices for the development of intelligent medical devices and offers beneficial guidance for the design and application of future intelligent health monitoring systems.

Photoacoustic (PA) imaging provides deep tissue molecular imaging of chromophores with optical absorption contrast and ultrasonic resolution. Present PA imaging techniques are predominantly limited to one 2D plane per acquisition. 2D ultrasound transducers, required for real-time 3D PA imaging, are high-cost, complex to fabricate and have limited scalability in design. We present novel PCB-based 2D matrix ultrasound transducer arrays that are capable of being bulk manufactured at low-cost without using laborious ultrasound fabrication tools. The 2D ultrasound array specifications are easily scalable with respect to widely available PCB design and fabrication tools at low cost. To demonstrate scalability, we fabricated low (11 MHz) frequency 8x8 matrix array and high (40 MHz) frequency 4x4 matrix array by directly bonding an undiced polyvinylidene fluoride (PVDF) piezoelectric material of desired thickness to the custom designed PCB substrate. Characterization results demonstrate wideband PA receive sensitivity for both low (87%) and high (188%) frequency arrays. Volumetric PA imaging results of light absorbing targets inside optical scattering medium demonstrate improved spatial resolution and field of view with increase in aperture size.

Despite the well-established nature of non-destructive testing (NDT) technologies, autonomous monitoring systems are still in high demand. The solution lies in harnessing the potential of intelligent structures, particularly in industries like aeronautics. Substantial downtime occurs due to routine maintenance, leading to lost revenue when aircraft are grounded for inspection and repairs. This article explores an innovative approach using intelligent materials to enhance condition-based maintenance, ultimately cutting life-cycle costs. The study emphasizes a paradigm shift toward structural health monitoring (SHM), utilizing embedded sensors for real-time monitoring. Active thin film piezoelectric materials are proposed for their integration into composite structures. The work evaluates passive sensing through acoustic emission (AE) signals and active sensing using Lamb wave propagation, presenting amplitude-based and frequency domain approaches for damage detection. A comprehensive signal processing approach is presented, and the damage index and damage size correlation function are introduced to enable continuous monitoring due to their sensitivity to changes in material properties and defect severity. Additionally, finite element modeling and experimental validation are proposed to enhance their understanding and applicability. This research contributes to developing more efficient and cost-effective aircraft maintenance approaches through SHM, addressing the competitive demands of the aeronautic industry.

Nanofiber (NF) products exhibit outstanding performances in materials science, textiles, and medicine that cannot be realized using conventional technologies. However, the safety of such products is debated because of the potential health risks that nanomaterials pose and the lack of standardized guidelines for the safety evaluation of NF products. The global safety evaluations of nanomaterials have focused on evaluating the cytotoxicity of low-dimensional materials, including nanoparticles and nanotubes, based on OECD (Organization for Economic Co-operation and Development) criteria. NFs are one-dimensional materials with nanometer diameters and considerable lengths. Many fibers are applied in a densely woven web-like form, so assessing cellular penetration and fiber toxicity using the same methods is inappropriate. This study verifies the safety of the polyurethane (PU) and polyvinylidene fluoride (PVDF) polymers currently applied in filters and masks. To this end, polymer NFs were collected from each product, and the NFs were compared with reference samples using FT-IR and Raman spectroscopy. For the safety evaluation, DMSO stocks of varying concentrations of PVDF and PU NFs (at 0.5, 1, 5, and 10 μg/mL) were prepared. The cytotoxicity and inhibitory effects on nitric oxide production and protein expression obtained via Western blot were identified.

The polyethylene lithium-ion battery separator is coated with a polymer by means of a roll-to-roll (R2R) gravure coating scheme to enhance the thermal stability. The polyvinylidene fluoride (PVDF) or polyvinylidene fluoride-co-hexafluoropropylene (PVDF-HFP) is gravure-coated, and the pores are fabricated based on online nonsolvent-induced phase separation (NIPS). N-methylpyrrolidone is used as a solvent, and deionized water or a methanol mixture thereof is exploited as a nonsolvent in NIPS. Scanning electron microscopy confirms that the polymer film is formed and that the pores are well developed. The thermal shrinkage decreased by 20.0% and 23.2% compared to that of the bare separator due to the coating of PVDF and PVDF-HFP, respectively. The R2R gravure coating scheme is proven to be fully functional to tailor the properties of lithium-ion battery separators.

Piezoelectric nanogenerators have prospective uses for generating mechanical energy and powering electronic devices due to their high output and flexible behavior. In this research, the synthesis of the three-dimensional coral-like BaTiO3 (CBT) and its filling into a polyvinylidene fluoride (PVDF) matrix to obtain composites with excellent energy harvesting properties are reported. The CBT-based PENG has a 163 V voltage and a 16.7 µA current at a frequency of 4 Hz with 50 N compression. Simulations show that the high local stresses in the CBT coral branch structure are the main reason for the improved performance. The piezoelectric nanogenerator showed good durability at 5000 cycles, and 50 commercial light-emitting diodes were turned on. The piezoelectric nanogenerator generates a voltage of 4.68-12 V to capture the energy generated by the ball falling from different heights and a voltage of ≈0.55 V to capture the mechanical energy of the ball\'s movement as it passes. This study suggests a CBT-based piezoelectric nanogenerator for potential use in piezoelectric sensors that has dramatically improved energy harvesting characteristics.

The hydrophobic nature of Poly (vinylidene fluoride) (PVDF) is a significant barrier to use in ultrafiltration, resulting in fouling, flux decline, and reduced lifespan in water treatment. This study examines the effectiveness of different morphologies of CuO nanomaterials (NMs) (spherical, rod, plate, and flower), synthesized by the facile hydrothermal method, to modify PVDF membrane with PVP additive for improving the performance of water permeability and antifouling. Such membrane configurations with different morphologies of CuO NMs improved hydrophilicity with a maximum water flux of 222-263 L m-2h-1 compared to 195 L m-2h-1 for the bare membrane and exhibited excellent thermal and mechanical strengths. The characterization results exhibited that plate-like CuO NMs were dispersed uniformly in the membrane matrix, and their incorporation as a composite improved the membrane properties. From the antifouling test with the bovine serum albumin (BSA) solution, the membrane with plate-like CuO NMs had the highest flux recovery ratio (FRR) (∼91%) and the lowest irreversible fouling ratio (∼10%). The antifouling enhancement was due to less interaction between modified membranes and foulant. Further, the nanocomposite membrane showed excellent stability and negligible Cu2+ ion leaching. Overall, our findings provide a new strategy for developing inorganic nanocomposite PVDF membranes for water treatment.

Polyvinylidene fluoride (PVDF) dual-layer hollow fiber membranes were simultaneously fabricated by thermally induced phase separation (TIPS) and non-solvent induced phase separation (NIPS) methods using a triple orifice spinneret (TOS) for water treatment application. The support layer was prepared from a TIPS dope solution, which was composed of PVDF, gamma-butyrolactone (GBL), and N-methyl-2-pyrrolidone (NMP). The coating layer was prepared from a NIPS dope solution, which was composed of PVDF, N,N-dimethylacetamide (DMAc), and polyvinylpyrrolidone (PVP). In order to improve the mechanical strength of the dual-layer hollow fiber, a nucleating agent, sodium 2,2\'-methylene bis-(4,6-di-tert-butylphenyl) phosphate (NA11), was added to the TIPS dope solution. The performance of the membrane was evaluated by surface and cross-sectional morphology, water flux, mechanical strength, and thermal property. Our results demonstrate that NA11 improved the mechanical strength of the PVDF dual-layer hollow fiber membranes by up to 42%. In addition, the thickness of the coating layer affected the porosity of the membrane and mechanical performance to have high durability in enduring harsh processing conditions.

Volatile organic compounds (VOCs) are biomarkers of disease, which can be utilized for accurate diagnostics. The gold standard for VOC identification is gas chromatography-mass spectrometry (GC-MS) as it allows for structure elucidation and quantification. Headspace solid phase microextraction (HS-SPME) is often used in biomarker discovery due to its ability to preconcentrate VOCs prior to GC-MS analysis. However, HS-SPME GC-MS is time-consuming, expensive and requires trained personnel. Gas sensor arrays can detect VOC biomarkers at a point-of-care and therefore are more suitable for disease diagnostics in the clinic. Nevertheless, qualification and optimization of sensing layers is tedious as each VOC of interest needs to be tested individually. Therefore, using SPME fibers to extract VOCs and GC-MS to quantitate the analytes may be an efficient strategy with high throughput to tune sensing layers and increase analyte affinity. To investigate this, suspensions of polyvinylidene fluoride (PVDF) and polyvinylidene fluoride-carbon black (PVDF-CB) fabricated at varying concentration were immobilized on SPME fibers through physical deposition, used to extract urinary VOCs and were subject to GC-MS analysis. The addition of CB shows increased fiber performance in terms of total integrated signal and sensitivity toward individual VOCs. PVDF-CB fibers were compared to a commercial polydimethylsiloxane (PDMS) SPME fiber run using the same method. The PVDF-CB fiber outperformed the commercial fiber in detecting numerous urinary VOCs of interest. Results of this study show not only that custom SPME fiber performance can be evaluated through GC-MS analysis, but the capability of custom fibers to adsorb urinary VOCs can be tuned based on properties of interest. Hence, this method may be utilized as an analytical tool to characterize and tune gas sensing layers with high analytical throughput.