Dismemberment and subsequent burning are common methods employed in an attempt to conceal or destroy evidence. While kerf characteristics can be utilised to identify tool(s) used for dismemberment, further research is necessary to assess the effect of burning on these characteristics. In this study, a back (tenon) saw (13 teeth per inch) was used to manually inflict trauma on Ovis aries de-fleshed femur bones (n = 18). Three different cut marks (shallow false start, incomplete cut and complete transection) were made on the mid-shaft of each bone. Subsequently, the bones were burned for 20 minutes in a muffle furnace. Three burn temperatures were assessed: 400 °C, 600 °C and 800 °C. Saw mark characteristics of each cut type were assessed and compared pre- and post-burning. All pre-existing trauma was recognisable post-burning; however, metric and morphological alterations were apparent. An increase in kerf width was observed at 600 °C in false start lesions and 800 °C in incomplete cuts. Breakaway spur thickness decreased post-burning (at 400 °C and 800 °C) but length was not significantly affected. Mean inter-striation distance decreased post burning at all temperature groups. Saw marks were distinguishable from heat-related fractures across all temperature groups. One false start lesion was obliterated at 800 °C. Exit chipping, pull-out striae as well as striation regularity appeared to be more enhanced after heat exposure. These alterations indicate a temperature-dependent impact on these characteristics. Further research is necessary to assess the role of burn duration.

In most experimental protocols, false starts are produced on dry bones obtained through a maceration process for anthropological analyses, for the sake of reproducibility. Although this allows for controlled experimental conditions, the absence of soft parts when experimentally creating false starts does not correspond to the real conditions of criminal dismemberment. The main objective of this study was to determine if the results of experimental work on the characteristics of false starts were valid under medico-legal conditions. In this experimental study, a hand saw (rip saw, wavy set, TPI 32) was used. 240 false starts were produced on human and pig bones. Randomly, the false starts were either produced on a dry bone or on a flesh bone. The criteria for microscopic analysis included the shape of the walls, the shape and visibility of striae on the floor, the shape of the profile, and the minimum width of the false start. On human bone, 100% of the false starts produced on a bone that had previously undergone a maceration process for anthropological analyses (dry bone) allowed the definition of all the blade characteristics. This was the case for 78.3% on bone in the presence of soft tissue (flesh bone). The striae on the floor of the false start are in some cases less visible with flesh bones, implying that it may be more difficult to conclude on the characteristics of a saw under medico-legal conditions.

Forensic toolmark examiners compare marks between those observed on an item/surface and those made by a reference implement, such as a particular tool or weapon, to provide an opinion of the likelihood of common origin. It is widely accepted that such comparison opinions need to be underpinned by empirical research, and this study aimed to add to the knowledge base relied upon when developing and comparing saw marks in bone, a substrate encountered in body dismemberment cases. Porcine bones were used as a human proxy; they were either fresh with residual soft tissue and bodily fluids present (\'wet\') to replicate dismembered bones shortly post-mortem, or processed to remove soft tissue and moisture content (\'dry\') to represent cases of dismemberment after an extended period of decomposition and exposure. The bones were cut using one implement of each of five classes: hand saw, mitre saw, reciprocating saw, oscillating saw, and serrated knife. They were cut, either completely through (except for serrated knife), giving two surfaces per cut to examine, or to a depth up to 3 mm (false starts). Five replicates per combination of bone condition, saw, and cut type gave 130 bone samples. These were then cleaned and cast using Isomark Silicone Polymer Compound or Mikrosil, giving 260 cast samples. All bone and cast samples were photographed, examined for various class characteristic markers, and specific markers measured. No significant differences between Isomark and Mikrosil casts were observed when compared side-by-side, demonstrating suitability of both materials for casting of saw marks on bone. Although saw marks presented more class characteristic markers on dry than wet bones, calculations of tooth distances and measurements of kerf width (KW) from marks did not significantly differ between bone conditions, with exception of the reciprocating saw that produced false start marks with significantly larger minimum KW on wet than dry samples. Further analysis supported that tooth distances on marks made by hand and oscillating saws are sufficiently accurate for the determination of saw teeth per inch (TPI). However, one tooth distance on marks made by reciprocating saws did not accurately represent TPI. Finally, examination of presence or absence of class characteristic markers on each saw mark demonstrated consistent variation between saw classes. These results enabled the development of exclusion-based decision trees, and a reference database (available on request), for use by toolmark examiners in their evaluation of saw types based on class characteristic markers observed in cut bone.

We report on a case of criminal dismemberment and attempted scalping of a homicide victim with a \"Mohawk\" haircut. Case findings are presented. A review of the literature was performed for scalping in its historical and cultural context and particularly in criminal dismemberment and mutilation: Historically, scalping was prevalent in many ancient cultures around the world, where scalps were taken as trophies or \"proof of kill\", much like shrunken heads, trophy skulls, and other artefacts. Scalping was particularly widespread in Northern America in the context of tribal warfare, both before and after colonization. The iconic \"Mohawk\" haircut is closely linked with scalping, as it was meant to taunt the enemy. In the modern forensic context, scalping constitutes a form of criminal mutilation. However, cases of criminal dismemberment and mutilation are rare in forensic casework. Our literature review revealed a low number of scalping in criminal dismemberment and mutilation cases. The documentation was overall poor. Positioning scalping within the classification of criminal mutilation and dismemberment was difficult. In literature, even though case numbers were small, the majority of \"textbook scalping\" cases were German. The presented case, to our best knowledge, is the first modern-day photo-documented case of (attempted) scalping, even more so of a person wearing a \"Mohawk\".

Minimum kerf width (MKW) is often assessed in medicolegal cases of skeletal sharp force trauma and can provide information about the tool used. Previously published saw MKW research focuses on the relationship between MKW and saw blade set width (width of the saw blade including tooth set). Despite these publications using various measurement tools and methods to collect MKW, error in MKW measurements is not well-documented. The goal of this research was to investigate MKW measurement precision in terms of intraobserver error, interobserver error, and the effects of measurement modality (e.g., calipers versus stereo microscope). The study sample consisted of 351 incomplete cuts made with 27 diverse saws. MKW was collected using three methods: (1) inserting the internal caliper jaws into the incomplete kerf, (2) placing the external caliper jaws on the cortical surface, and (3) using a digital stereo microscope and associated measurement software. For each method, intraobserver error and interobserver error were assessed. Differences in measurements taken with the three measurement modalities were assessed for each observer as well. Relative technical error of measurement (rTEM) and coefficients of reliability indicate that internal caliper and stereo microscope measurements had the lowest intra- and interobserver error (rTEM = 3.72% to 6.15%; r = 0.98-0.996). External caliper measurements performed the worst (rTEM: intra = 8.53% and inter = 21.32%). There was higher precision between internal caliper and stereo microscope measurements than with the external caliper measurements. This research highlights the need for measurement standardization.

Saws are common tools used in postmortem dismemberment to alter human remains. Dismemberment may coincide with other concealment methods such as disposal in aquatic environments, so forensic anthropologists must recognize how taphonomy affects saw mark preservation. This study focuses on exposure of saw cut bone to a fluvial environment. Cross sections from pig humeri cut by a 7 TPI saw were evaluated on all cut surfaces for tooth hop (TH), exit chipping, and breakaway spurs. Pre-fluvial exposure, features were measured by two observers using a stereomicroscope while a one-dimensional profilometer was used to define surface roughness. Bones were randomly assigned to control or experimental groups and within each divided by duration of exposure (24, 48, 72, and 96 h). Control groups (four cross sections) were exposed to water in a 3-meter-long hydraulic channel; experimental groups (20 cross sections) were exposed to water and sediment in a 12-meter-long sediment-recirculating hydraulic channel. Velocity was maintained at 0.45 m/s. All measurements were repeated post-exposure. Observer A recorded 268 TH (mean: 3.70 ± 0.34 mm); post-exposure, count increased by 16.79% (mean: 3.71 ± 0.29 mm). Observer B recorded 247 TH (mean: 3.46 ± 0.42 mm); post-exposure, count decreased by 29.15% (mean: 3.36 ± 0.33 mm). All TPI estimates calculated include the 7 TPI saw. Exit chipping lost flakiness (in both channels), but was still visible. Breakaway spurs were not visibly altered. Surface staining was limited to bones exposed to sediment. Roughness was significantly lower in experimental groups post-fluvial exposure (W = 5705, p < 0.05). Overall, this fluvial environment did not obliterate saw mark evidence from bone.

This case study reports the advantages of micro-CT to aid the investigative process in a complex dismemberment case. Micro-CT was successfully implemented to scan all skeletal remains of a dismembered female. The digital models were utilized to (i) screen for any further injuries not related to the dismemberment, (ii) provide measurements from false starts non-destructively, and (iii) visually represent the evidence in a structured format in court to improve the understanding of the forensic evidence by the jury. Acquiring high-resolution scans in this manner improved the efficiency of the forensic investigation by screening the remains and provided complementary toolmark evidence to the investigating team and forensic pathologist. A total of 14 false starts were identified along with the directionality of each dismemberment cut. Furthermore, the visual 3D representation of the remains in court provided a powerful tool to communicate this important evidence to the jury and form a prosecution narrative. As a forensic radiological method, micro-CT provided valuable information both in the investigation and the court presentation.

In forensic anthropology, saw mark analysis plays an important role in cases of criminal dismemberment. Autopsy saw is not used by the perpetrator in cases of dismemberment, but the forensic pathologist may accidentally create false starts with this saw during an autopsy, especially while sampling bones for further analysis, and these autopsy false starts can be confused with false starts produced by the offender. In this study, the characteristics of 20 false starts were compared using stereomicroscopy (SM) and scanning electron microscopy (SEM). These bone false starts were selected at random from a previous study of 100 false starts created by an electrical oscillating autopsy saw on human femoral bones. That study had enabled the categorization of the lesions into two groups (\"superficial group\" and \"deep group\") with a 0.52 mm depth cut off, based on the dramatic differences in lesion characteristics between these two groups. In the current study, SEM confirmed the characteristics of the false starts (walls and profile shapes, striae, bone islands and bone debris were studied), and above all explained the mechanism whereby oval bone islands in deep lesions are formed. Bone islands are due to the horizontal and vertical movement of the oscillating autopsy blade.

The estimation of the postmortem interval (PMI) is of critical importance in forensic routine. The most frequently applied methods, however, are all restricted to specific time periods or must be excluded under certain circumstances. In the last years it has been shown that the analysis of muscle protein degradation has the potential to contribute to according delimitations in practice. In particular, upon biochemical analysis, the specific time points of degradation events provide reasonable markers for PMI delimitation. Nevertheless, considerable research is yet required to increase the understanding of protein decomposition and how it is affected by individual and environmental influencing factors. This is best investigated under standardized conditions, however, a considerate selection of proxies, regarding costs, effort, and expected outcome is required. Here, we use pigs to compare muscle protein decomposition in whole bodies and dismembered body parts (amputated hind limbs). Not only do experiments on body parts reduce the costs and allow easier handling in basic research, but also they aid to investigate the practical application of PMI estimation in dismembered body parts, or other extensive injuries, which are not unusual scenarios in crime investigation. Specifically, we investigated whether there are differences in the degradation rates of selected muscle proteins, sampled from dismembered legs and from hind limbs attached to whole pig bodies. Our results show distinct time-dependent degradation patterns of muscle proteins in a predictable manner regardless of sample origin. We are able to demonstrate that amputated hind limbs are suitable proxies for the analysis of muscle protein degradation, especially to investigate certain influencing factors and establish according standardized models.

We identified 43 cases of mutilation homicides in a nationwide population-based study in Sweden during the period of 1991-2017. 70% of cases were classified as defensive mutilations where the main motive was disposal of the body, while 30% were classified as offensive, that is, due to an expression of strong aggression, necro-/sexual sadism, or psychiatric illness. In comparison with a previous study covering mutilation homicides in Sweden between 1961 and 1990, we noted an increase in incidence. The percentage of cases involving mutilation had increased from 0.5% of all homicides in the 1960s to 2.4% in the 2010s. The most common cause of death was sharp force, but in 28% of the cases, the cause of death could not be determined. The clearance rate in cases of mutilation homicide was 67%, and in a large majority of the cases, the offender was known to the victim. With regards to gender women made up 44% of the victims, whilst men constituted 56% of the victims and a total of 95% of the offenders. Half of the offenders had a personality disorder, however, only 13% were sentenced to forensic psychiatric care.