Ferrous alloys, particularly steels, form a specialized class of metallic materials extensively employed in industrial sectors to combat deterioration and failures caused by wear. Despite their commendable mechanical properties, steels are not immune to wear-induced degradation. In this context, surface nanocrystallization (SNC) technologies have carved a distinct niche for themselves by enabling the nanostructuring of the surface layer (with grain sizes < 100 nm). This process enhances overall mechanical properties to a level desirable for wear resistance while preserving the chemical composition. Existing literature has consistently highlighted the efficacy of various SNC methods in improving the wear resistance of ferrous alloys, positioning SNC as a promising tool to extend materials\' service life in practical applications. This review provides a comprehensive examination of the SNC techniques employed in surface treatment of ferrous alloys and their impact on wear behavior. We delved into the underlying mechanisms governing wear in SNC-treated Fe-based alloys and concluded with a discussion on current challenges and future perspectives in this evolving field.

UNASSIGNED: The aim was to evaluate the difference in the heat generated between zirconia (Zr) and steel (SS) drills, during implant site preparation.
UNASSIGNED: This systematic review followed the PRISMA methodology criteria and used the JBI Critical Assessment Guidelines for Quasi-Experimental Studies for quality assessment. The electronic search was conducted by using the PubMed/MEDLINE, Embase, and Cochrane Library databases to January 2023. The formulated population, intervention, comparison, outcome (PICO) question was \"Do zirconia drills generate less heat than steel drills during implant site preparation?\". The meta-analysis was based on an inverse variance (IV) method.
UNASSIGNED: This review included 10 studies in vitro that used zirconia drills compared to steel drills with or without coatings. The meta-analysis indicated a significant difference between Zr drills and SS drills, with a lower bone temperature variation with Zr drills.
UNASSIGNED: Despite the limitations of this review, it was concluded that Zr drills had significantly less temperature variation than SS drills.

Biomedical alloys, like many engineering alloys, have chemical or physical heterogeneities at the surface, and such heterogeneities can potentially act as sites for pit initiation. Alloys of particular interest are 316/316L (and 316LVM) stainless steel, nitinol, and CoCr alloys. This review focuses on the sites-generally inclusions-that have been associated with pitting in various studies of biomedical alloys in simulated physiological solutions. The effect of these sites is discussed in relation to factors such as type and size. For both 316/316L stainless steel and nitinol, pitting has been found to initiate at two different types of inclusions: sulfide and oxide inclusions in stainless steel, and carbide and oxide inclusions in nitinol. Sulfide inclusions tend to be the predominant sites for pitting on 316/316L stainless steel, while there is some evidence to suggest that carbide inclusions may be more effective than oxide inclusions for pitting on nitinol. CoCrMo alloys differ from the other two alloys in that, although particles can be present in the form of carbides, the carbides typically do not provide sites for pit initiation except possibly for alloys with a high-C content, certain heat treatments, and when anodically polarized to high potentials. CoNiCrMo differs further in that TiN inclusions can be present in the vicinity of pits and might be associated with them, but irrespective of the initiation site, any pits are unlikely to grow because of repassivation.

This study investigates the potential of using bacteriophages to control foodborne pathogen biofilms on stainless steel surfaces in the food industry. Biofilm-forming bacteria can attach to stainless steel surfaces, rendering them difficult to eradicate even after a thorough cleaning and sanitizing procedures. Bacteriophages have been proposed as a possible solution, as they can penetrate biofilms and destroy bacterial cells within, reducing the number of viable bacteria and preventing the growth and spread of biofilms. This systematic review and meta-analysis evaluates the potential of bacteriophages against different biofilm-forming foodborne bacteria, including Cronobacter sakazakii, Escherichia coli, Staphylococcus aureus, Pseudomonas fluorescens, Pseudomonas aeruginosa and Listeria monocytogenes. Bacteriophage treatment generally causes a significant average reduction of 38 % in biofilm formation of foodborne pathogens on stainless steel. Subgroup analyses revealed that phages are more efficient in long-duration treatment. Also, applying a cocktail of phages is 1.26-fold more effective than applying individual phages. Phages at concentrations exceeding 107 PFU/ml are significantly more efficacious in eradicating bacteria within a biofilm. The antibacterial phage activity decreases substantially by 3.54-fold when applied at 4 °C compared to temperatures above 25 °C. This analysis suggests that bacteriophages can be a promising solution for controlling biofilms in the food industry.

To systematically assess the scientific literature for the prevalence of failure rate of fixed orthodontic bonded retainer (FOBR).
Randomized clinical trials (RCTs) and prospective non-RCTs involving participants who had FOBR fitted were included. The Cochrane Central Register of Controlled Trials, Web of science, MEDLINE, and EMBASE via OVID were searched from inception to January 2023. Risk of bias was assessed using the Cochrane RoB 2 and Newcastle-Ottawa tools. The main outcome was the failure rate of FOBRs. The secondary outcome was to identify factors that can influence the failure of FOBR. Meta-analyses and sensitivity analyses were undertaken using Revman, version5.4. A random-effects model was used. Quality assessment using Grading of Recommendations Assessment, Development, and Evaluation.
Thirty-four studies (25 RCTs and 9 prospective clinical studies) (3484 participants) were included in this review. The overall failure rate of bonded retainers, after excluding high-risk studies, was 35.22% (95% confidence interval [CI] 27.46-42.98). The failure rate is increased with the duration of follow up; with short-term follow-up rate 24.18% (95% CI 20.16-28.21), medium-term follow up 40.09% (95% CI 30.92-49.26), and long-term follow up 53.85% (95% CI 40.31-67.39). There is a low level of evidence to suggest there is no statistically significant difference in the failure rate of fixed retainers using direct versus indirect bonding methods, using liquid resin versus without liquid resin, and fibre-reinforced composite retainers compared to multi-stranded stainless steel retainers.
There is low-quality evidence to suggest that the failure rate of FOBR is relatively high. There is a need for high-quality, well-reported clinical studies to assess factors that can influence the failure rate of FOBR.
CRD42021190910.

Comparing computer-aided design and computer-aided manufacturing (CAD/CAM) fixed retainers and conventional fixed retainers for their effectiveness in orthodontic patients using systematic review and meta-analysis of literature.
A comprehensive search was conducted in MEDLINE, Web of Science, EMBASE, Scopus, Cochrane\'s CENTRAL, Google Scholar, Ovid, and LILACS up to May 2023, with no language or date restrictions.
Only randomized clinical trials (RCTs) that complied with PICO questions were included, and the Cochrane Risk of Bias 2.0 (RoB 2) tool was used to assess the risk of bias in the included studies.
Using custom-piloted forms, relevant data were retrieved from the included studies. Then a random-effects inverse variance meta-analysis was used to pool the results. Primary outcomes were stability of treatment results measured through dental cast measurements and periodontal status, while secondary outcomes were failure rates and patient-reported outcomes.
Seven RCTs with 601 participants were included in the review. In the short term (≤6 months), the meta-analysis showed no significant differences in inter-canine distance or arch length between CAD/CAM and conventional fixed retainers in mandibular retainers. However, for Little\'s irregularity index, single-stranded stainless-steel retainers were notably worse than Ni-Ti CAD/CAM retainers at 3 and 6 months, while multi-stranded stainless-steel retainers only diverged from CAD/CAM at the 6-month milestone, despite the overall clinical inconsequence of these changes. CAD/CAM retainers were associated with a lower plaque index than traditional retainers but no significant difference in gingival index. Failure rates did not differ significantly between CAD/CAM and other types of retainers in mandibular retainers. Nonetheless, one study had a high amount of CAD/CAM retainer failures leading to the study being stopped.
In the short term, CAD/CAM fixed retainers show promise as an alternative to traditional retainers. They may enhance periodontal health, as indicated by lower plaque index scores than conventional retainers. However, extensive research is needed to determine the long-term durability and effectiveness of CAD/CAM retainers in orthodontic treatment, particularly regarding their failure rate. Until comprehensive evidence is available, the use of CAD/CAM retainers should be tailored for each case.
The protocol for this systematic review was registered at PROSPERO with the ID CRD42023412741.

The primary aim of this study was to provide a review of the types and frequency of orthodontic brackets, molar bands and orthodontic auxiliaries used for patients undergoing orthognathic surgery. The secondary aim was to evaluate the risk of failure of these items during orthognathic surgery.
From three Dutch hospitals, 124 adult patients were included in this prospective cohort study. Five independent researchers collected the data during surgery using a specifically created data extraction form. The type of surgery, surgeon, orthodontist and type of orthodontic bracket, molar band or auxiliary were noted for each tooth. To evaluate their failure risk, the following variables were noted: failure and site; and type and cause of failure.
Stainless-steel brackets were the most frequently (75.8%) used bracket type seen in patients undergoing orthognathic surgery. Ceramic brackets were seen in 24.2% of the cases and were only applied in the anterior region. Molar bands were present in 58.9% of the patients and mostly with bands on the first molars in combination with bonded tubes on the second molars. In 32.2% of all cases, one or more failures were noted. One-third of all failures were described as detachment of the molar tube on the most posterior molar. Kobayashi ligatures and powerpins showed the highest risk of failure (odds ratio [OR] 3.70, 95% confidence interval [CI] = 1.91-7.15). No significant difference in failure rate was found between stainless-steel brackets, molar bands (OR 0.34, 95% CI = 0.08-1.43) and ceramic brackets (OR 0.44, 95% CI = 0.14-1.45).
Stainless-steel brackets, ceramic brackets, molar bands and surgical hooks are suitable for orthognathic cases. Kobayashi ligatures and powerpins had a significantly higher risk of failure so are not recommended for temporary intraoperative maxillomandibular fixation (TIO-MMF).

The pickling sludge produced in the stainless steel pickling process is a hazardous waste and disposal in landfill poses a potential environmental risk. Stainless steel pickling sludge contains metal elements such as Fe, Cr, and Ni and substances such as SiO2 and CaO, which have good value for resource recycling. This paper briefly introduces the generation, nature, and hazards of stainless steel pickling sludge; and clustering analysis of relevant literature keywords in recent years; and detailed analysis and comparison of sludge obtained from different steel mills and resource utilization process. The current situation of pickling sludge resource utilization and the development of relevant policies in China in recent years are summarized, and new thoughts on the direction of its resource utilization are put forward.

The press and sinter method remains the standard among powder metallurgy processes for powdered stainless-steel materials. It delivers low cost, low oxidation rate, and adequate corrosion resistance. Furthermore, 17-4PH is a martensitic stainless-steel that is commonly used for high-strength and medium-ductility stainless steel parts. However, a few studies have investigated the press and sinter method for producing 17-4PH parts. This shortage is due to the high hardness (low compressibility) of 17-4PH powder. Thus, the main objective of this study is to evaluate the press and sinter method in terms of the manufacturing process, the influencing factors, and the theoretical basis of press and sinter methods in conjunction with metal injection molding technology for the production of 17-4PH parts. First, the literature and monographs are examined and summarized to cover the previous results, research progress, development trends, and applications of press and sinter method 17-4PH parts. Following the theoretical analysis, the practical investigation was conducted by producing parts with cold pressing from 800 to 1600 MPa, followed by sintering: the sintering temperature was 1200 °C for one hour under a protective vacuum atmosphere. ImageJ analysis was performed to measure the sinter density. The results showed an increase in relative sinter density from 84.43% to 96.43% for 800 and 1600 MPa, respectively, while the earlier results reached 93.47%. Overall, the press and sinter method enables the production of high-hardness 17-4PH parts with a high density, without using additives like lubricants, wax, or alloying elements.

Joining immiscible materials such as copper and stainless steel together is a significant concern due to distinct mechanical and metallurgical properties across the joint line, such as melting points, the coefficient of linear thermal expansion, and thermal conductivity. The joint properties of copper to stainless steel welds are in great demand for various mechanical components of the international thermonuclear experimental reactor, ultra-high vacuum system, plan wave linear-accelerator or linac structure, and heat exchanger. These dissimilar-metals joints offer excellent flexibility in design and production, leading to a robust structure for many cutting-edge applications. Hence, the present article reviews the copper to stainless steel joining mechanism under different solid-state processing conditions. The present understanding says that defect-free strong joints between the dissimilar metals are systematically possible. Apart from this understanding, the authors have identified and highlighted the gaps in the research exploration to date. Moreover, a sustainable methodology to achieve a desirable weld of copper to stainless steel depends on favorable processing conditions.