Vibration sensors are widely used in many fields like industry, agriculture, military, medicine, environment, etc. However, due to the speedy upgrading, most sensors composed of rigid or even toxic materials cause pollution to the environment and give rise to an increased amount of electronic waste. To meet the requirement of green electronics, biodegradable materials are advocated to be used to develop vibration sensors. Herein, a vibration sensor is reported based on a strategy of pencil-drawing graphite on paper. Specifically, a repeated pencil-drawing process is carried out on paper with a zigzag-shaped framework and parallel microgrooves, to form a graphite coating, thus serving as a functional conductive layer for electromechanical signal conversion. To enhance the sensor\'s sensitivity to vibration, a mass is loaded in the center of the paper, so that higher oscillation amplitude could happen under vibrational excitation. In so doing, the paper-based sensor can respond to vibrations with a wide frequency range from 5 Hz to 1 kHz, and vibrations with a maximum acceleration of 10 g. The results demonstrate that the sensor can not only be utilized for monitoring vibrations generated by the knuckle-knocking of plastic plates or objects falling down but also can be used to detect vibration in areas such as the shield cut head to assess the working conditions of machinery. The paper-based MEMS vibration sensor exhibits merits like easy fabrication, low cost, and being environmentally friendly, which indicates its great application potential in vibration monitoring fields.

This article proposes a modular and passive all-metal lens to achieve near-field focusing with adjustable focus. The proposed lens consists of all-metal units with the phase coverage range exceeding 360°, and the arrangement of units is guided by the phase compensation method. Specifically, using the strategy of module unit synthesis, the arrangement of lens units under different focuses can be assembled arbitrarily, which reduces the production costs by 39.3% and improves the freedom of lens design. The simulation and experimental results show that the lens exhibits excellent focusing properties and freely changes the position of the expected focus (0.30 m-0.75 m). Therefore, the modular all-metal lens designed in this article has the characteristics of high transparency and a high degree of freedom, which can provide low-cost and lightweight solutions for various applications in the field of antennas, such as near-field target detection, microwave imaging, biomedicine, and so on.

OBJECTIVE: To evaluate the clinical performance and financial costs of breast-specific gamma imaging (BSGI) as a biopsy-reducing problem-solving strategy in patients with inconclusive diagnostic imaging findings.
METHODS: A retrospective analysis of all patients for whom BSGI was utilized for inconclusive imaging findings following complete diagnostic mammographic and sonographic evaluation between January 2013 and December 2018 was performed. Positive BSGI findings were correlated and biopsied with either US or stereotactic technique with confirmation by clip location and pathology. After a negative BSGI result, patients were followed for a minimum of 24 months or considered lost to follow-up and excluded (22 patients). Results of further imaging studies, biopsies, and pathology results were analyzed. Net savings of avoided biopsies were calculated based on average Medicare charges.
RESULTS: Four hundred and forty female patients from 30 to 95 years (mean 55 years) of age were included in our study. BSGI demonstrated a negative predictive value (NPV) of 98.4% (314/319) and a positive predictive value for biopsy of 35.5% (43/121). The overall sensitivity was 89.6% (43/48), and the specificity was 80.1% (314/392). In total, 78 false positive but only 5 false negative BSGI findings were identified. Six hundred and twenty-one inconclusive imaging findings were analyzed with BSGI and a total of 309 biopsies were avoided. Estimated net financial savings from avoided biopsies were $646 897.
CONCLUSIONS: In the management of patients with inconclusive imaging findings on mammography or ultrasonography, BSGI is a problem-solving imaging modality with high NPV that helps avoid costs of image-guided biopsies.

To continue sleep research activities during the lockdown resulting from the COVID-19 pandemic, experiments that were previously conducted in laboratories were shifted to the homes of volunteers. Furthermore, for extensive data collection, it is necessary to use a large number of portable devices. Hence, to achieve these objectives, we developed a low-cost and open-source portable monitor (PM) device capable of acquiring electroencephalographic (EEG) signals using the popular ESP32 microcontroller. The device operates based on instrumentation amplifiers. It also has a connectivity microcontroller with Wi-Fi and Bluetooth that can be used to stream EEG signals. This portable single-channel 3-electrode EEG device allowed us to record short naps and score different sleep stages, such as wakefulness, non rapid eye movement sleep (NREM), stage 1 (S1), stage 2 (S2), stage 3 (S3) and stage 4 (S4). We validated the device by comparing the obtained signals to those generated by a research-grade counterpart. The results showed a high level of accurate similarity between both devices, demonstrating the feasibility of using this approach for extensive and low-cost data collection of EEG sleep recordings.

Many advanced technologies have been employed in high-performance active matrix displays, including liquid crystal displays, organic light-emitting diode displays, and micro-light-emitting diode displays. On the other side, there exists a strong demand for cost reduction, and it is one of the low-cost schemes for integrating the driver circuit in a panel based on thin-film transistor technologies. This paper reviews the overall concept, operation principles, and various circuit approaches in shift registers for scanning pulse generation. In addition, it deals with the implementation of additional functionalities in gate drivers to support pixel compensation, multi-line driving, in-cell capacitive touch screen, pixel sensing, and adaptive scanning region control.

OBJECTIVE: T1 mapping and T1-weighted contrasts have a complimentary but currently under utilized role in fetal MRI. Emerging clinical low field scanners are ideally suited for fetal T1 mapping. The advantages are lower T1 values which results in higher efficiency and reduced field inhomogeneities resulting in a decreased requirement for specialist tools. In addition the increased bore size associated with low field scanners provides improved patient comfort and accessibility. This study aims to demonstrate the feasibility of fetal brain T1 mapping at 0.55T.
METHODS: An efficient slice-shuffling inversion-recovery echo-planar imaging (EPI)-based T1-mapping and postprocessing was demonstrated for the fetal brain at 0.55T in a cohort of 38 fetal MRI scans. Robustness analysis was performed and placental measurements were taken for validation.
RESULTS: High-quality T1 maps allowing the investigation of subregions in the brain were obtained and significant correlation with gestational age was demonstrated for fetal brain T1 maps ( p < 0 . 05 $$ p<0.05 $$ ) as well as regions-of-interest in the deep gray matter and white matter.
CONCLUSIONS: Efficient, quantitative T1 mapping in the fetal brain was demonstrated on a clinical 0.55T MRI scanner, providing foundations for both future research and clinical applications including low-field specific T1-weighted acquisitions.

Various approaches have been proposed for bridge structural health monitoring. One of the earliest approaches proposed was tracking a bridge\'s natural frequency over time to look for abnormal shifts in frequency that might indicate a change in stiffness. However, bridge frequencies change naturally as the structure\'s temperature changes. Data models can be used to overcome this problem by predicting normal changes to a structure\'s natural frequency and comparing it to the historical normal behaviour of the bridge and, therefore, identifying abnormal behaviour. Most of the proposed data modelling work has been from long-span bridges where you generally have large datasets to work with. A more limited body of research has been conducted where there is a sparse amount of data, but even this has only been demonstrated on single bridges. Therefore, the novelty of this work is that it expands on previous work using sparse instrumentation across a network of bridges. The data collected from four in-operation bridges were used to validate data models and test the capabilities of the data models across a range of bridge types/sizes. The MID approach was found to be able to detect an average frequency shift of 0.021 Hz across all of the data models. The significance of this demonstration across different bridge types is the practical utility of these data models to be used across entire bridge networks, enabling accurate and informed decision making in bridge maintenance and management.

Fluorescence-related experimental techniques play an important role in biochemistry, molecular biology, and cell biology. However, fluorescence-related experiments are rarely included in the laboratory courses of most Chinese universities. This is mainly due to the conflict between large class size (50-60 students in one room) and funding/space limitations to purchase and accommodate enough fluorescence detection equipment. Here, we proposed feasible and economical Do It Yourself (DIY) procedures of a hand-held fluorescence detector set-FluorDetector to support the development of laboratory courses. Tested on several samples, clear fluorescence signals could be directly observed by FluorDetector and photographed with a smartphone. In addition, FluorDetector was able to turn a conventional stereomicroscope into a fluorescence stereomicroscope, detecting fluorescence signals with clean background. FluorDetector is easy to make with a 3D printer, with an extremely low cost ($200 each) when compared with a commercial fluorescence microscope or fluorescence stereomicroscope, and almost as sensitive as a microplate reader in measuring fluorescence. Therefore, FluorDetector is a possible strategy to solve the problem and help to integrate fluorescence-related experimental modules in laboratory courses.

Dual-polarization programmable metasurfaces can flexibly manipulate electromagnetic (EM) waves while providing approximately twice the information capacity. Therefore, they hold significant applications in next-generation communication systems. However, there are three challenges associated with the existing dual-polarization programmable metasurfaces. This article aims to propose a novel design to address them. First, the design overcomes the challenge of element- and polarization-independent controls, enabling more powerful manipulations of EM waves. Second, by using more energy-efficient tunable components and reducing their number, the design can be nearly passive (maximum power consumption of 27.7 mW), leading to a significant decrease in the cost and power consumption of the system (at least two orders of magnitude lower than the power consumption of conventional programmable metasurfaces). Third, the design can operate in a broad bandwidth, which is attractive for practical engineering applications. Both the element and array of the metasurface are meticulously designed, and their performance has been carefully studied. The experiments demonstrate that 2D wide-angle beam scanning can be realized. Moreover, secure communication based on directional information modulation can be implemented by exploiting the metasurface and an efficient discrete optimization algorithm, showing its programmable, multiplexing, broadband, green, and secure features.

In the face of rising population, erratic climate, resource depletion, and increased exposure to natural hazards, environmental monitoring is increasingly important. Satellite data form most of our observations of Earth. On-the-ground observations based on in situ sensor systems are crucial for these remote measurements to be dependable. Providing open-source options to rapidly prototype environmental datalogging systems allows quick advancement of research and monitoring programs. This paper introduces Loom, a development environment for low-power Arduino-programmable microcontrollers. Loom accommodates a range of integrated components including sensors, various datalogging formats, internet connectivity (including Wi-Fi and 4G Long Term Evolution (LTE)), radio telemetry, timing mechanisms, debugging information, and power conservation functions. Additionally, Loom includes unique applications for science, technology, engineering, and mathematics (STEM) education. By establishing modular, reconfigurable, and extensible functionality across components, Loom reduces development time for prototyping new systems. Bug fixes and optimizations achieved in one project benefit all projects that use Loom, enhancing efficiency. Although not a one-size-fits-all solution, this approach has empowered a small group of developers to support larger multidisciplinary teams designing diverse environmental sensing applications for water, soil, atmosphere, agriculture, environmental hazards, scientific monitoring, and education. This paper not only outlines the system design but also discusses alternative approaches explored and key decision points in Loom\'s development.