Immunocompromised people developed mucormycosis as a result of the COVID-19 outbreak. Antifungal medications, surgical excision of infected tissues, and therapy of underlying metabolic problems are available forms of treatment. Usually, surgery entails completely excising the affected area. The patient is at risk for nasal twang, nasal cavity leaks, and impaired masticatory function because of these anomalies. The obturator prosthesis may form an oro-nasal seal in such problems. Additionally, lowering the prosthesis weight contributes to improved stability and retention. This case report explains a novel flasking technique to lessen the prosthesis weight and a modified impression technique to capture the palatal deformity.

The most common complication post COVID-19is mucormycosis. It is an opportunistic infection caused by the fungus mucormycetes which belongs to the order Mucorales. This infection can spread from the oral cavity to the nasal cavity and sometimes also involve the orbit. Surgical resection of the affected region followed by its prosthetic rehabilitation is one of the viable treatment options. In this case report, we will discuss the problems in designing and fabricating a hollow bulb obturator and its solutions.

Prosthetic rehabilitation of a partial or total maxillectomy with an obturator is the most acceptable treatment option. The hollowing of the obturator prosthesis is beneficial as it reduces the stresses over the underlying and surrounding tissues. A simple technique of fabricating a hollow bulb obturator has been discussed in this article. At the step of the packing of a denture, the hollow wax pattern of the defect area is formed with modeling wax. This hollow wax pattern is filled with water and is allowed to freeze to form an ice block. This ice block is removed from the wax pattern and is interposed between two layers for heat-cured acrylic resin and is then cured. After processing the denture, the water is retrieved by making a small hole in denture base, which is packed after hollowing with a cold cure acrylic resin. A lightweight prosthesis with a uniform thickness was achieved with a readily available and easily retrievable material, i.e., ice.

Defects involving the face and maxilla present a challenge to the prosthodontists as these have a direct effect on aesthetics, function as well as the psychology of the patient. An array of problems awaits the clinician from restoring the previous contour of the oral cavity, facial form, etc. to the mental state of the patients. This article deals with the rehabilitation of a hemimaxillectomy patient with a facial defect, using an interim hollow bulb obturator and a silicone facial prosthesis, which helped to improve the general well being of the patient. Rehabilitative procedures provide patients considerable care so that they can continue their life with confidence.

Maxillary defects occur either as a result of surgical resection of malignant tumors of the nasal cavity and paranasal sinuses or of the congenital causes. Rehabilitation of the patients with maxillectomy defects presents a challenge in restoring the lost form, function and speech. Maxillary interim obturators in prosthetic reconstruction of the defects are often complicated with lack of adequate retention, stability, and support. This case report presents the simplified approach, to rehabilitate a case of sub-total maxillectomy due to squamous cell carcinoma of maxillary sinus, using a closed hollow bulb obturator prosthesis fabricated with a \"U\" loop and a modified buccal flange for enhanced retention of the prosthesis.

The most frequent type of treatment for patients diagnosed with a malignant neoplasia of the oral cavity is surgical resection of the tumor. Ablative surgery may be followed by a reconstructive phase, in which the surgeon may choose between local flaps, nonvascularized bone grafts or free vascularized flaps to close the surgical site, depending on the general conditions of the patient. Esthetic and functional results are challenging to achieve for the prosthodontist, as variable amount of hard and soft tissues are removed. This report describes the fabrication of a two-piece hollow obturator for a 19-year-old patient who underwent wide surgical excision of the osteosarcoma of the maxilla and was rehabilitated to function. In this case, the surgical site was covered with submental flap, and the second piece of the obturator provided fullness to the lost malar prominence.

Loss of maxillo facial structures due to neoplasm, trauma and accidents gives inconsolable mental, physical and psychological agony to a person\'s dignified life in his living society. Surgical reconstruction was not feasible for all cases and certain cases needs prosthetic rehabilitation. In this clinical case report, an innovative, simple three part maxillo orbital prosthesis fabrication using magnets was explained.

Prosthodontic rehabilitation of acquired defects of the maxilla is a challenge in terms of reestablishing oronasal separation. Most of the times these goals are met by means of obturator prosthesis. Preservation of the remaining hard and soft tissues in such patients is very much essential in order to have a good retention, stability and support for the prosthesis. It is very much imperative to fabricate a prosthesis to provide proper function to the patient. Various techniques have been developed to enhance the retention and stability of the prosthesis, some of them being extension of the obturator bulb into the undercuts within the defect, use of magnets, implants etc. Telescopic crowns have been an adjunctive utility to prosthetic dentistry since a very long time. The biomechanics of telescopic crowns aid in providing a good retention and stability to the prosthesis. In the following clinical report a patient with a status of Subtotal Hemi Maxillectomy is presented in whom telescopic copings were incorporated into the cast hollow bulb obturator to enhance the retention and stability of the prosthesis.

Defects can form after tumors in the maxillary region are resected surgically. Maxillofacial defects can affect a patient\'s physical, psychological, and social status. Surgery reduces the residual teeth and tissue\'s ability to provide optimal cross-arch support, stability, and retention. The design of the obturator can improve the esthetics of the prosthesis and give it a more lifelike appearance. This case report describes the fabrication of a cast metal framework design for a partial obturator prosthesis in a maxillectomy patient.

OBJECTIVE: To evaluate the effect of bulb height of hollow bulb obturator prosthesis on articulation and nasalance.
METHODS: A total of 10 patients, who were to undergo maxillectomy falling under Aramany class-I and II, with normal speech and hearing pattern were selected for the study. They were provided 2 maxillary obturators, one extending full height of the defect and other with bulb height approximately up to inferior nasal concha. The patients were asked to wear each obturator for 6 weeks and the speech analysis was done to measure changes in articulation and nasalance at 6 different stages of treatment i.e. preoperative, postoperative (after complete healing), 24h and 6 weeks after providing full bulb height obturator and reduced bulb height obturator. Articulation was measured objectively for distortion, addition, substitution and omission by speech pathologist and nasalance was measured by Dr. SPEECH software.
RESULTS: Comparison between full and reduced bulb height for nasalance and articulation, showed that there was no statistical significant difference (P>0.05) between the two for both the parametres.
CONCLUSIONS: Articulation and nasality improves after providing obturator. Articulation and nasalance both are independent of bulb height.