Atmospheric drying method for fabricating aerogels is considered the most promising way for casting aerogels on a large scale. However, the organic solvent exchange, remaining environmental pollution risk, is a crucial step in mitigating the impact of surface tension during the atmospheric drying process, especially for wet gel formed through the alkoxy-derived sol-gel process, such as melamine-formaldehyde resin (MF) aerogel. Herein, a tough polymer-assisted in situ polymerization was proposed to fabricate MF resin aerogel with a combination of mechanical toughness and strength, enabling it to withstand the capillary force during water evaporation. The monolithic MF resin aerogel through the sol-gel method can be directly prepared without additional network strengthening or organic solvent exchange. The resulting MF resin aerogel exhibits a homogeneous as well as hierarchical structure with macropores and mesopores (~6 μm and ~5 nm), high compressive modulus of 31.8 MPa, self-extinguishing property, and high-temperature thermal insulation with 97 % heat decrease for butane flame combustion. This work presents a straightforward and environmentally friendly method for fabricating MF resin aerogels with nanostructures and excellent performance in open conditions, exhibiting various applications.

Interest in the development of eco-friendly, sustainable, and convenient bio-based coatings to enhance flame retardancy and antibacterial properties in cotton fabrics is growing. In this work, chitosan was protonated at its amino groups using a method with a high atom economy using an equimolar amount of amino trimethylene phosphonic acid (ATMP), resulting in the fabrication of a single-component chitosan-based multifunctional coating (ATMP-CS), thereby avoiding any additional neutralization or purification steps. Cotton fabrics coated with various loads of ATMP-CS were prepared through a padding-drying-curing process. The morphology, thermal stability, mechanical properties, antibacterial properties, flame-retardant behavior, and flame-retardant mechanism of these fabrics were investigated. The coating exhibited excellent film-forming properties, and it imparted a uniform protective layer onto the surfaces of the cotton fabrics. When the load capacity reached 11.5%, the coated fabrics achieved a limiting oxygen index of 29.7% and successfully passed the VFT test. Moreover, the ATMP-CS coating demonstrated antibacterial rates against Escherichia coli and Staphylococcus aureus reaching 95.1% and 99.9%, respectively. This work presents a straightforward and gentle approach to fabricating colorless, environmentally friendly, and highly efficient fabric coatings that have potential applications in promoting the use of bio-based materials.

With the increasing severity of energy shortages and environmental pollution, there is an urgent need for advanced thermal insulation materials with excellent comprehensive performance, including low thermal conductivity, high flame resistance, and strong compressive strength. Herein, an anisotropic composite aerogel based on cellulose nanofibers (CNF), calcium alginate (CA), and boric acid (BA) is fabricated using a directional freeze-drying strategy. The CA and BA, as double cross-linking agents, associated with oriented porous structure provide the resultant aerogel with good mechanical strength. Additionally, self-flame retardant CA and BA act as synergistic flame retardants that endow the aerogel with excellent flame retardance properties such as a limiting oxygen index value of 44.2 %, UL-94 V-0 rating, and low heat release. Furthermore, this composite aerogel exhibits outstanding thermal insulation performance with a low thermal conductivity of approximately 30 mW m-1 K-1. Therefore, the composite aerogel is expected to have a wide potential application in areas such as construction, automotive industry, batteries, petrochemical pipelines, and high-temperature reaction devices.

Naturally colored cotton (NCC) offers an environmentally friendly fiber for textile applications. Processing white cotton fiber into textiles requires extensive energy, water, and chemicals, whereas processing of NCC skips the most polluting activity, scouring-bleaching and dyeing; therefore, NCC provides an avenue to minimize the harmful impacts of textile production. NCC varieties are suitable for organic agriculture since they are naturally insect and disease-resistant, salt and drought-tolerant. Various fiber shades, ranging from light green to tan and brown, are available in the cultivated NCC (Gossypium hirsutum L.) species. The pigments responsible for the color of brown cotton fiber are proanthocyanidins or their derivatives synthesized by the flavonoid pathway. Due to pigments, the NCC has excellent ultraviolet protection properties. Some brown cotton varieties exhibited superior thermal resistance of fiber that can be used to make fabrics with enhanced flame retardancy. Here, we review molecular mechanisms involved in the pigment production of brown cotton and challenges in breeding NCC varieties with a wide range of colors but without penalty in fiber quality. Also, we discuss opportunities for NCC with flame-retarding properties in textile applications.

The phosphoramide phosphorus ester phosphate ammonium (PPEPA) flame retardant was synthesized by phosphorus oxychloride and ethanolamine, and its structure was characterized by nuclear magnetic resonance and Fourier transform infrared spectroscopy (FTIR). Cotton textiles treated with 20 wt% PPEPA (CT-PPEPA3) would have high durability and flame retardance. The limiting oxygen index (LOI) of CT-PPEPA3 was found to be 46.5 %, while after undergoing 50 laundering cycles (LCs) following the AATCC 61-2013 3 A standard, the LOI only decreased to 31.4 %. Scanning electron microscopy and X-ray diffraction analyses suggested the penetration of PPEPA molecules into the interior of cotton fibers, resulting in a minor alteration of the cellulose crystal structure. The excellent durability, FTIR, and energy-dispersive X-ray of CT-PPEPA3 provided evidence for the formation of -N-P(=O)-O-C- and -O-P(=O)-O-C- covalent bonds between the PPEPA molecules and cellulose. The -N-P(=O)-O-C- bond exhibited a p-π conjugation effect, leading to enhanced stability and improved durability of the flame-retardant cotton textiles. Vertical flame, thermogravimetric, and cone calorimetry tests demonstrated that the CT-PPEPA3 underwent condensed-phase and synergistic flame retardation. Additionally, these finished cotton textiles retained adequate breaking strength and softness, making them suitable for various applications. In conclusion, the incorporation of the -N-P(=O)-ONH4 group into the phosphorus ester phosphate ammonium flame retardant demonstrated effective enhancement of the fire resistance and durability of treated cotton textiles.

Soft materials bearing rigid, lightweight, and vibration-dampening properties offer distinct advantages over traditional wooden and metal-based fillings for spent fuel transport casks, due to their low density, tunable structure, excellent mechanical properties, and ease of processing. In this study, a novel type of rigid polyurethane foam is prepared using a conventional polycondensation reaction between isocyanate and hydroxy groups. Moreover, the density and size of the pores in these foams are precisely controlled through simultaneous gas generation. The as-prepared polyurethane exhibits high thermal stability exceeding 185 °C. Lifetime predictions based on thermal testing indicate that these polyurethane foams could last up to over 60 years, which is double the lifetime of conventional materials of about 30 years. Due to their occlusive structure, the mechanical properties of these polymeric materials meet the design standards for spent fuel transport casks, with maximum compression and tensile stresses of 6.89 and 1.37 MPa, respectively, at a testing temperature of -40 °C. In addition, these polymers exhibit effective flame retardancy; combustion ceased within 2 s after removal of the ignition source. All in all, this study provides a simple strategy for preparing rigid polymeric foams, presenting them as promising prospects for application in spent fuel transport casks.

The flame-retardant paper has gradually evolved into a necessary material in various industries as a result of the rising importance of fire safety, energy efficiency, and environmental preservation. Traditional cellulose paper requires the addition of a large amount of flame retardants to achieve flame retardancy, which poses a serious threat to mechanical quality and the environment. Therefore, there is an urgent need to develop inorganic fiber flame-retardant paper with good flexibility, high thermal stability, and inherent flame retardancy. Herein, inspired by the \"brick-and-mortar\" layered structure of nature nacre, we developed a layered composite paper with a unique alternating arrangement of organic-inorganic fibers by synergistically integrating environmentally sustainable basalt fiber (BF) and high-performance aramid nanofibers (ANFs) through a vacuum-assisted filtration process. The as-prepared ANFs/BF composite paper exhibited low thermal conductivity (0.024 W m-1 K-1), high tensile strength (54.22 MPa), and excellent flexibility. Thanks to its excellent thermal stability, the mechanical strength remains at a high level (92%) after heat treatment at 300 °C for 60 min. Furthermore, the peak heat release rate and smoke generation of ANFs/BF composite paper decreased by 44.6 and 95.3%, respectively. Therefore, the composite paper is promising for applications as a protective layer in flexible electronic devices, cables, and fire-retardant and high-temperature fields.

Miniaturization of modern micro-electronic devices urges the development of multi-functional thermal management materials. Traditional polymer composite-based thermal management materials are promising candidates, but they suffer from single functionality, high cost, and low fire-resistance. Herein, a multifunctional liquid metal (LM)-bridged graphite nanoplatelets (GNPs)/ aramid nanofibers (ANFs) film is fabricated via a facile vacuum-assisted self-assembly approach followed by compression. ANFs serve as interfacial binders to link LM and GNPs together via hydrogen bondings and π-π interactions, while LM bridges the adjacent layer of GNPs to endow a fast thermal transport by phonons and electrons. The resultant composite films exhibit a high bidirectional thermal conductivity (In-plane: 29.5 W m-1K-1 and through-plane: 5.3 W m-1K-1), offering a reliable and effective cooling. Moreover, the as-fabricated composite films exhibit superior flame-retardance (peak of heat release rate of 4000J g-1), outstanding Joule heating performance (200 °C at supplied voltage of 3.5 V), and excellent electromagnetic interference shielding effectiveness (EMI SE of 62 dB). This work provides an efficient avenue to fabricate multifuntional thermal management materials for micro-electronic devices, battery thermal management, and artificial intelligence.

With the escalating environmental and health concerns over petroleum-based plastics, sustainable and biodegradable cellulosic materials are a promising alternative to plastics, yet remain unsatisfied properties such as fragility, inflammability and water sensitivity for practical usage. Herein, we present a novel dual-network design strategy to address these limitations and fabricate a high-performance cellulosic composite bioplastic metafilm with the exceptional mechanical toughness (23.5 MJ m-3 ), flame retardance, and solvent resistance by in situ growth of cyclotriphosphazene-bridged organosilica network within bacterial cellulose matrix. The phosphorus, nitrogen-containing organosilica network, verified by the experimental and theoretical results, plays a triple action on significantly enhancing tensile strength, toughness, flame retardance and water resistance of composite bioplastic metafilm. Furthermore, cellulosic bioplastic composite metafilm demonstrates a higher maximum usage temperature (245 °C), lower thermal expansion coefficient (15.19 ppm °C-1 ), and better solvent resistance than traditional plastics, good biocompatibility and natural biodegradation. Moreover, the composite bioplastic metafilm have a good transparency of average 74 % and a high haze over 80 %, which can serve as an outstanding substrate substitute for commercial polyethylene terephthalate film to address the demand of flexible ITO films. This work paves a creative way to design and manufacture the competitive bioplastic composite to replace daily-used plastics.

Novel hybrid flame retardants containing zinc hydroxystannate and carbon nanotubes (ZHS-CNTs) were synthesized using the coprecipitation method, and the structure and morphology of ZHS-CNTs were investigate using an X-ray powder diffractometer (XRD), scanning electron microscope (SEM), transmission electron microscopy (TEM) and thermogravimetric analyzer (TGA). Then, the ZHS, CNTs and ZHS-CNTs were incorporated into EP, respectively, and the flame-retardant and smoke inhibition performance of the composites were compared and studied. Among the three composites, the EP/ZHS-CNT composites have the highest improvements on the fire resistance and smoke inhibition properties. With only 2.0 wt.% ZHS-CNT hybrids, the pHRR of EP/ZHS-CNT composite materials is reduced by 34.2% compared with EP. Moreover, the release of toxic gases including CO, CO2 and SPR from the composites was also effectively inhibited. The mechanisms of flame retardant and smoke inhibition were investigated and the improved properties were generally ascribed to the synergistic flame-retardant effects between ZHS and CNTs, the catalyzing effect of ZHS and the stable network structure of CNTs.