Flexible electrothermal heaters have attracted abundant attention in recent years due to their wide applications, but their preparation with high efficiency remains a challenge. Here in this work, a highly stable and bending-tolerant flexible heater was fabricated with graphite nanosheets and cellulose fibers through a scalable papermaking procedure. Its electrothermal property can be enhanced by a hot-pressing treatment and introduction of cationic polyacrylamide (CPAM) during the papermaking protocol. The flexible heater may quickly reach its maximum temperature of 239.8 °C in around 1 min at a voltage of 9 V. The power density was up to 375.3 °C cm2 w-1. It appeared to have a high tolerance for bending deformation with various curvatures, and the temperature remained stable even under 100 bending with frequency of around 0.17 Hz. Over 100 alternatively heating and cooling cycles, it worked stably as well. It was proved to be used as wearable heating equipment, soft heaters, and aircraft deicing devices, suggesting its great prospect in the field of heat management.

Perovskite quantum dots (PQDs) have attracted emerging attention as fluorescent and light-absorbing materials for next-generation optoelectronics due to their outstanding properties and cost-efficiency. However, PQD thin film suffers significant instability due to structure and material failures, which hinders their application in flexible and reliable PQD-based advanced wearable devices. Herein, we use commercial cellulose fiber-based filter paper as a substrate to synthesize PQDs in situ and fabricate PQD-paper free-standing flexible composite film. The abundant hydroxy capping ligands of cellulose fibers and the unique dense network structure of the filter paper can facilitate confined crystallization, forming strong interactions between the PQDs and substrate, the unpackaged PQD composite film showed extraordinary stability (>30 days) in the air with high humidity (90%). Meanwhile, the strong interaction between PQDs and paper enables an ultrasimple drop-cast synthesis process with excellent process tolerance, making it customizable and easy to scale up (10 cm in diameter). Due to the uniformly dispersed PQDs on cellulose fibers of the substrate, the composite demonstrates impressive photo-responsive properties. Photodetector (PD) arrays were designed on free-standing PQD paper and flexible graphitic electrodes, and circuits were fabricated by drawing. The PD arrays can work as optical and electrical dual-mode image sensors with incredible bending robustness, enduring up to 100,000 cycles at 180°.

As increasing fiber hydrophobicity can significantly improve the paper dewatering process, we found that replacing SBKP and HBKP with 0.5% superhydrophobic CPGMA can significantly improve the dewatering of paper sheets. Therefore, it can be concluded that if CPGMA has little effect on paper properties, it will have potential industrial value in the papermaking industry. Consequently, it is necessary to further study the effect of the CPGMAs@CPAM/SiO2/APAM system on paper properties. To evaluate the application potential of the system in the papermaking industry, we investigated the effects of CPGMAs, which replaced the fibers in the stocks, on the paper properties in the CPAM/SiO2/APAM system. The findings demonstrate that as the CPGMA replacement increased, the paper\'s tensile strength, bursting strength, tear resistance, and folding endurance all declined. The trend can be segmented into two phases: a rapid decrease for substitution amounts below 0.5% and a gradual decline for substitution amounts exceeding 0.5%. When replaced with a small amount of CPGMAs, there was a negligible effect on these properties. Second, the paper air permeability increased with the CPGMA substitution amount in the stock. Furthermore, the trend of paper air permeability can be divided into two stages-a rapid stage with a substitution amount of <0.5% and a slow stage with a substitution amount of >0.5%. A small amount of CPGMAs could distinctly improve the paper\'s air permeability. Third, CPGMAs, which replaced fibers in the stock, minutely affected the paper formation. A small amount of CPGMAs substantially boosted the efficacy of the process of paper manufacture and certain characteristics of the paper, and it had a negligible impact on the strength of paper. The CPGMAs@CPAM/SiO2/APAM technology has the potential to improve the retention and filtration performance of CPAM/SiO2/APAM.

The present study reports on the preparation of a cellulose fiber (CF) composite from D. lutescens, combined with copper oxide nanoparticles (DL@CF/CuO), to prolong the shelf life of tomatoes after harvest. The isolated cellulose fiber material was comprehensively characterized using XRD, FTIR, and FE-SEM analyses. The DLCF and DL@CF/CuO nanoparticles exhibited crystalline cellulose, as indicated by the XRD investigation. Both DLCF and DL@CF/CuO showed O-H and C-H FTIR spectra with identifiable vibrational peaks. The FE-SEM images depicted the dispersion of DL@CF/CuO-based fibers in a cellulose fiber matrix containing CuO nanoparticles. A 0.3% (wt/wt), a solution of DL@CF/CuO was coated onto the surface of early ripening tomato fruits. After a 25-day storage period at 25-29 °C and 85% RH, the results showed a significant extension in the shelf life of the tomato fruits, in line with changes in physiological properties and fruit quality. The extension of shelf life in tomato fruit epidermis treated with DL@CF/CuO was confirmed through FE-SEM analysis. L929 fibroblast cells were treated with the developed DL@CF/CuO nanocomposite, and no signs of toxicity were detected up to 75 µg/mL. Additionally, the DL@CF/CuO nanocomposite exhibited significant antifungal activity against Aspergillus flavus. In conclusion, this study provides novel insights for sustainable food security and waste control in the agricultural and food industries.

Amidoxime groups were successfully introduced to develop a novel amidoxime-functionalized cellulose fiber (AO-Cell) for absorptive removal of heavy metal ions in wastewater. The chemical structure, and the competitive adsorption of Cu2+ and Zn2+ by AO-Cell were investigated by experiments study, Density functional theory (DFT) and molecular dynamic (MD) simulation. The results showed the N and O atoms in the amidoxime group can spontaneously interact with Cu2+ and Zn2+ through sharing long pair electrons to generate stable coordination structure, which was the dominant adsorption mechanism. Besides, the enlarged surface area, improved hydrophilicity and dispersion offered by AO-Cell facilitate the adsorption process by increasing the accessibility of absorption sites. As results of these synergetic modification, AO-Cell can remain effective in a wide pH range (1-6) and reach adsorption equilibrium within 60 min. At optimal conditions, the achieved theoretical adsorption capacity is as high as 84.81 mg/g for Cu2+ and 61.46 mg/g for Zn2+ in the solution with multiple ions. The competition between Cu2+ and Zn2+ in occupying the absorption sites arises from the difference in the metallic ion affinity and covalent index with the adsorbent as demonstrated by the MD analysis. Importantly, AO-Cell demonstrated favorable recyclability after up to 10 adsorption-desorption cycles.

Functional Lyocell fibers gain interest in garments and technical textiles, especially when equipped with inherently bioactive features. In this study, Lyocell fibers are modified with an ion exchange resin and subsequently loaded with copper (Cu) ions. The modified Lyocell process enables high amounts of the resin additive (>10%) through intensive dispersion and subsequently, high uptake of 2.7% Cu throughout the whole cross-section of the fiber. Fixation by Na2CO3 increases the washing and dyeing resistance considerably. Cu content after dyeing compared to the original fiber value amounts to approx. 65% for reactive, 75% for direct, and 77% for HT dyeing, respectively. Even after 50 household washes, a recovery of 43% for reactive, 47% for direct and 26% for HT dyeing is proved. XRD measurements reveal ionic bonding of Cu fixation inside the cellulose/ion exchange resin composite. A combination of the fixation process with a change in Cu valence state by glucose/NaOH leads to the formation of Cu2O crystallites, which is proved by XRD. Cu fiber shows a strong antibacterial effect against Staphylococcus aureus and Klebsiella pneumonia bacteria, even after 50 household washing cycles of both >5 log CFU. In nonwoven blends with a share of only 6% Cu fiber, a strong antimicrobial (CFU > log 5) and full antiviral effectiveness (>log 4) was received even after 50 washing cycles. Time-dependent measurements already show strong antiviral behavior after 30 s. Further, the fibers show an increased die off of the fungal isolate Candida auris with CFU log 4.4, and nonwovens made from 6% Cu fiber share a CFU log of 1.7. Findings of the study predestines the fiber for advanced textile processing and applications in areas with high germ loads.

Compared with conventional formwork casting materials, 3D printed concrete (3DPC) is characterized by large amounts of cementitious materials, a low aggregate-binder ratio, and a large water evaporation area, which make the printed materials and structures highly prone to plastic shrinkage and cracking. In this study, cellulose fibers were incorporated into concrete to improve its moisture distribution and increase its early-age strength. The effects of both dry and prewet cellulose fibers on properties of 3DPC were experimentally investigated. To ensure consistency in the amounts of dry fibers used, 0.5-2% dry cellulose fibers and 1-4% prewet cellulose fibers were adopted. The effects of the added cellulose fibers on printability, mechanical strength, shrinkage, and cracking performance of the 3DPC were experimentally studied. Particularly, a constraint method was developed to access the cracking behavior of 3DPC. Favorable shrinkage resistance was achieved, and the 120-day shrinkage decreased by 17.9% and 23.3% by addition of 2% dry fibers and 4% prewet fibers, respectively. Cracking was eliminated with addition of 4% prewet fibers, without influencing the printability and mechanical properties.

Cellulose/ZnO (CZ) nanocomposites are promising antimicrobial materials known for their antibiotic-free nature, biocompatibility, and environmental friendliness. In this study, cellulose fibers extracted from lotus petioles were utilized as a substrate and decorated with various shapes of ZnO nanoparticles (NPs), including small bean, hexagonal ingot-like, long cylindrical, and hexagonal cylinder-shaped NPs. Increasing zinc salt molar concentration resulted in highly crystalline ZnO NPs forming and enhanced interactions between ZnO NPs and -OH groups of cellulose. The thermal stability and UV-visible absorption properties of the CZ samples were influenced by ZnO concentration. Notably, at a ZnO molar ratio of 0.1, the CZ 0.1 sample demonstrated the lowest weight loss, while the optical band gap gradually decreased from 3.0 to 2.45 eV from the CZ 0.01 to CZ 1.0 samples. The CZ nanocomposites exhibited remarkable antibacterial activity against both Staphylococcus aureus (S. aureus, Gram-positive) and Escherichia coli (E. coli, Gram-negative) bacteria under visible light conditions, with a minimum inhibitory concentration (MIC) of 0.005 mg/mL for both bacterial strains. The bactericidal effects increased with higher concentrations of ZnO NPs, even achieving 100% inhibition. Incorporating ZnO NPs onto cellulose fibers derived from lotus plants presents a promising avenue for developing environmentally friendly materials with broad applications in antibacterial and environmental fields.

Constructing a high-performance ultraviolet shielding film is an effective way for addressing the growing problem of ultraviolet radiation. However, it is still a great challenge to achieve a combination of multifunctional, excellent mechanical properties and low cost. Here, inspired by the multiscale structure of biomaterials and features of lignin, a multifunctional composite film (CNF/CMF/Lig-Ag) is constructed via a facile vacuum-filtration method by introducing micron-sized cellulose fibers (CMF) and lignin-silver nanoparticles (Lig-Ag NPs) into the cellulose nanofibers (CNF) film network. In this composite film, the microfibers interweave with nanofibers to form a multiscale three-dimensional network, which ensures satisfactory mechanical properties of the composite film. Meanwhile, the Lig-Ag NPs are employed as a multifunctional filler to enhance the composite film\'s antioxidant, antibacterial and ultraviolet shielding abilities. As a result, the prepared CNF/CMF/Lig-Ag composite film demonstrates excellent mechanical properties (with tensile strength of 133.8 MPa and fracture strain of 7.4 %), good biocompatibility, high thermal stability, potent antioxidant and antibacterial properties. More importantly, such composite film achieves a high ultraviolet shielding rate of 98.2 % for ultraviolet radiation A (UVA) and 99.4 % for ultraviolet radiation B (UVB), respectively. Therefore, the prepared CNF/CMF/Lig-Ag composite film shows great potential in application of ultraviolet protection.

Cellulose-based foams present a high potential for noise insulation applications. These materials are bio-degradable, eco-friendly by both embedded components and manufacturing process, have low density and high porosity, and are able to provide good noise insulation characteristics compared with available petroleum-based foams currently used on a large scale. This paper presents the results of some investigations performed by the authors in order to improve the functional characteristics in terms of free surface wettability and structural integrity. Native xylan and xylan-based derivatives (in terms of acetylated and hydrophobized xylan) were taken into account for surface treatment of cellulose foams, suggesting that hemicelluloses represent by-products of pulp and paper industry, and xylan polysaccharides are the most abundant hemicelluloses type. The investigations were mainly conducted in order to evaluate the level to which surface treatments have affected the noise insulation properties of basic cellulose foams. The results indicate that surface treatments with xylan derivatives have slowly affected the soundproofing characteristics of foams, but these clearly have to be taken into account because of their high decrease in wettability level and improving structural integrity.