Microfluidics is an important technology for the biomedical industry and is often utilised in our daily lives. Recent advances in micro-milling technology have allowed for rapid fabrication of smaller and more complex structures, at lower costs, making it a viable alternative to other fabrication methods. The microfluidic chip fabrication developed in this research is a step-by-step process with a self-contained wet milling chamber. Additionally, ethanol solvent bonding is used to allow microfluidic chips to be fully fabricated within approximately an hour. The effect of using this process is tested with quantitative contact profileometery data to determine the expected surface roughness in the microchannels. The effect of surface roughness on the controllability of microparticles is tested in functional microfluidic chips using image processing to calculate particle velocity. This process can produce high-quality channels when compared with similar studies in the literature and surface roughness affects the control of microparticles. Lastly, we discuss how the outcomes of this research can produce rapid and higher-quality microfluidic devices, leading to improvement in the research and development process within the fields of science that utilise microfluidic technology. Such as medicine, biology, chemistry, ecology, and aerospace.

BACKGROUND: The effects of air-polishing on exposed root dentin surfaces are largely unknown, as there are only few studies which show heterogeneous results. Thus, this study was to investigate roughness changes of exposed dentin surfaces after air-polishing and the influence of subsequent polishing with cup and paste.
METHODS: Totally 54 teeth with exposed root dentin surfaces were treated using a split-mouth design by either air-polishing with erythritol and a rubber cup with polishing paste on the test side, or rubber cup and paste alone. Teeth were finally cleaned using a sonic tooth brush. Impressions were taken at relevant time points and replicated using epoxy resin. The resulting casts were profilometrically analysed to obtain the average surface roughness (sRa) and maximum peak-to-valley height (sRz), which are given as the mean ± standard deviation in μm.
RESULTS: After air-polishing, in comparison to the baseline, there was a slight but significant increase in sRa (0.168 ± 0.143, p < 0.001), but sRz did not change (-0.471 ± 4.857, p = 0.936). Subsequent polishing with cup and paste and cleaning with a sonic toothbrush did not reduce the surface roughness (sonic toothbrush-air-polishing, sRa -0.044 ± 0.081, p = 0.218; sRz -0.551 ± 3.563, p = 0.903).
CONCLUSIONS: The use of erythritol led to a slight increase in the roughness of the dentin surface, which was not reduced by polishing with a cup and paste. Polishing paste did not seem to conceal surface irregularities.

Deflectometric profilometers are used to precisely measure the form of beam shaping optics of synchrotrons and X-ray free-electron lasers. They often utilize autocollimators which measure slope by evaluating the displacement of a reticle image on a detector. Based on our privileged access to the raw image data of an autocollimator, novel strategies to reduce the systematic measurement errors by using a set of overlapping images of the reticle obtained at different positions on the detector are discussed. It is demonstrated that imaging properties such as, for example, geometrical distortions and vignetting, can be extracted from this redundant set of images without recourse to external calibration facilities. This approach is based on the fact that the properties of the reticle itself do not change - all changes in the reticle image are due to the imaging process. Firstly, by combining interpolation and correlation, it is possible to determine the shift of a reticle image relative to a reference image with minimal error propagation. Secondly, the intensity of the reticle image is analysed as a function of its position on the CCD and a vignetting correction is calculated. Thirdly, the size of the reticle image is analysed as a function of its position and an imaging distortion correction is derived. It is demonstrated that, for different measurement ranges and aperture diameters of the autocollimator, reductions in the systematic errors of up to a factor of four to five can be achieved without recourse to external measurements.

OBJECTIVE: To evaluate, in a prospective clinical study over 5 years with ex vivo 3D profilometry analyses, the intraoral wear of Polymer-Infiltrated Ceramic Network (PICN) CAD-CAM composite restorations used in severe tooth wear treatment with the One-Step No-Prep technique.
METHODS: 192 PICN (Vita Enamic) restorations on molars and premolars were included in a prospective clinical study involving patients treated according to the One-step No-prep protocol (n = 7). All patients showed clinical signs of bruxism. Replicas of restorations on molars and premolars were realized at each evaluation time (baseline and then every year up to 5 years) and scanned to perform 3D profilometry. Baseline and recall scans were superimposed with Geomagic Control software. The mean material wear was calculated for the full occlusal area (FOA) and for the occlusal contact area (OCA), respectively. Clinical evaluation of restorations was performed at recall.
RESULTS: At 5 years, the estimated mean material wear for FOA was inferior to the accuracy threshold of the profilometry measurement chain. For OCA, the estimated mean wear of the material was - 27.97 µm. This material wear was shown to be significantly influenced by time (p < 0.0001) and patient (p = 0.026), while the type of tooth (molar or premolar) had no influence. At 5 years, the survival and the success rates of restorations were 99.48% and 90.62%, respectively.
CONCLUSIONS: The PICN material exhibits a low wear process in the treatment of severe tooth wear despite the presence of clinical signs of bruxism, and it constitutes a suitable material for the One-step No-prep technique.

Corrosion processes at cut edges of galvanized steels proceed as highly localized electrochemical reactions between the exposed bulk steel matrix and the protective thin metallic coating of a more electrochemically active material. Scanning microelectrochemical techniques can thus provide the spatially resolved information needed to assess the corrosion initiation and propagation phenomena, yet most methods scan cut edge sections as embedded in insulating resin to achieve a flat surface for scanning purposes. In this work, the galvanized coatings on both sides of the material were concomitantly exposed to simulated acid rain while characterizing the cut edge response using SECM and SVET techniques, thereby maintaining the coupled effects through the exposure of the whole system as rather realistic operation conditions. The cut edges were shown to strongly promote oxygen consumption and subsequent alkalization to pH 10-11 over the iron, while diffusion phenomena eventually yielded the complete depletion of oxygen and pH neutralization of the nearby electrolyte. In addition, the cathodic activation of the exposed iron was intensified with a thinner coating despite the lower presence of sacrificial anode, and preferential sites of the attack in the corners revealed highly localized acidification below pH 4, which sustained hydrogen evolution at spots of the steel-coating interface.

The aim for this pilot study was to investigate the effect of a sodium fluoride varnish on step height measured by a profilometer from human enamel worn by healthy volunteers with a novel in situ/ex vivo erosion design.
Healthy volunteers aged 18-70 years wore a palatal splint containing 8 human enamel samples and underwent two 3-day treatment periods for 6 h a day with a varnish containing sodium fluoride at 22,600 ppm and the control with the same ingredients but without fluoride. Each splint contained 4 polished and 4 unpolished samples. The interventions were applied to the surface of the enamel samples in randomised order, removed after 6 h, then immersed ex-vivo in 1 %, pH 2.7 citric acid for 2 min, repeated 4 times a day, over 2 days. Measurements of enamel were assessed blindly by microhardness on day 2 and by non-contact laser profilometry on day 3 for the two treatments.
24 volunteers, 2 males and 22 females aged 27-54 years, were screened and recruited. The delta microhardness, from polished samples removed at the end of day 2, for the control and fluoride treatment was 95.7 (22.9) kgf/mm2 and 123.7 (28.9) kgf/mm2, respectively (p < .005). The mean (SD) step height for the control polished enamel surfaces was 3.67 (2.07) µm and for the fluoride varnish was 1.79 (1.01) µm (p < .0005). The control unpolished enamel surfaces had a mean 2.09 (1.53) µm and the fluoride varnish was 2.11 (1.53) µm but no statistical difference was detected.
The results from this pilot study, utilizing an in-situ model where enamel was exposed to acid over the course of 2 days, demonstrated that a high fluoride varnish containing sodium fluoride at 22,600 ppm prevented erosive wear compared to a control on the polished enamel surfaces.
Intra-oral study demonstrated that a high fluoride varnish containing sodium fluoride at 22,600 ppm reduced erosive tooth wear.

Clinical assessment of progression of non-carious cervical lesions (NCCLs) is currently based on subjective methods. We hypothesize that 3D digital intraoral scanners (IOS) can provide quantitative outcomes for objective measuring and monitoring of NCCLs. This in vitro study verified the reliability of IOS to monitor dental structure loss of simulated NCCLs, in comparison to a reference bench-top 3D optical profilometer (BTS).
NCCLs of different severity levels (early, moderate, or severe, n = 150) were simulated in a preceding study. Impressions of the lesions were taken and scanned with both BTS (ProScan; Scantron) and IOS (TRIOS4; 3Shape). Generated 3D images were analyzed for volumetric tooth loss (mm3) by superimposition followed by subtraction analysis. ProForm (Scantron) and WearCompare (Leeds Digital Dentistry) software were used in association to BTS and IOS, respectively. Agreement was assessed using intraclass correlation coefficient (ICC, alpha=0.05) and Bland-Altman plots.
ICC (confidence interval at 95 %) between IOS and BTS for all data combined was 0.962 (0.942-0.973), showing excellent reliability. Subset analyses showed that NCCLs with lower volume loss (early- and moderate-stage lesions) resulted in moderate ICCs, whereas severe lesions showed excellent ICC. Bland-Altman plots demonstrated general good agreement, with narrower limits for early stage-lesions.
IOS data demonstrated good agreement to BTS, when measuring tooth structure loss in simulated NCCLs, with particularly higher ICC in more severe lesions. Considering the accessibility and ease-of-use, IOS showed to be a good alternative for the objective assessment of NCCLs in vitro.
3D intraoral scanners\' accessibility and objectivity make them potentially valuable tools for assessing and monitoring NCCLs.

To compare profilometry and microhardness of polished occlusal and buccal human enamel following a mechanical and chemical wear regime.
Enamel from polished human molars were sectioned into buccal and occlusal surfaces and randomly allocated into two groups (n = 10) and then exposed to 0.3 % citric acid at pH 2.7 for 10, 20, 40 and 60 mins each followed by abrasion with non-fluoridated toothpaste for 240 strokes in a reciprocating brushing machine. A white light profilometer with a spot size of 12 um measured mean step-height following each cycle. Microhardness indentations were conducted following the final cycled 60 mins erosion/abrasion using 0.01, 0.02, 0.1, 0.5 and 2.5 kgf indentation load. Statistical disparity were evaluated using a two-way ANOVA and post-hoc Sidak\'s multiple comparisons tests at α = 0.05.
After erosion/abrasion, the mean (SD) step-heights on occlusal and buccal surfaces were not significantly different until 60 mins, when occlusal surfaces exhibited greater step-heights, 32.9 µm (2.8) and 31.1 µm (1.8) and p = 0.02, respectively. Buccal and occlusal microhardness was statistically lower following erosion/abrasion at loads of 0.01 kgf (p = 0.0005) and 0.02 kgf (p = 0.0006) but no significant differences were observed in the microhardness between the surfaces at any loads.
The occlusal and buccal surfaces were not statistically different for microhardness or step height suggesting the susceptibility to wear is not related to the anatomy and structure of the tooth and is more likely related to other factors such as the environment.
The study emphasizes that a notable difference in wear between occlusal and buccal enamel surfaces emerges only after prolonged exposure to simultaneous chemical and mechanical stress. This finding necessitates a preventive dental approach that accounts for both the duration of exposure and environmental factors.

Nowadays, FRP composites are widely applied in the construction industry. Their inherent characteristics are used to strengthen structural elements made of various materials and to increase their durability. The following paper contains the results obtained in a conducted research program aimed at determining the ability to improve the durability of epoxy resin modified with the sonication process, microsilica and carbon nanotubes. The adhesive modified was used to adhere a CFRP tape to a concrete surface. Changes in the viscosity, physicochemical parameters and adhesion of the resin were studied. Selected parameters of the concrete substrate prepared using the sandblasting method, determined with the contact profilometry, were also taken into account. During the tests, attention was paid to the thorough execution and preparation of the samples. As a result of the research, it was demonstrated that the adhesion of the modified epoxy adhesive to concrete could be increased by approximately 28% in the case of the addition of carbon nanotubes and by up to 66% in the case of the addition of microsilica. The modifications used, in addition to increasing the adhesion of the resin to the concrete substrate, were also aimed at reducing the weakening of the adhesive joints caused by oxidation of the resin over time. The results obtained will serve as a basis for evaluating the possibility of their use in the practical reinforcement of structural reinforced-concrete elements.

To investigate the effect of toothbrush head configuration and dentifrice slurry abrasivity on the development of simulated non-carious cervical lesions (NCCLs) in vitro.
Extracted premolars were randomly allocated into 15 groups (n = 16) generated by the association between toothbrush head configuration (flat-trimmed, rippled, cross-angled/multilevel/rubbers added, cross-angled/multilevel/flex head, feathered) and dentifrice slurry abrasivity (low/medium/high). Teeth were mounted on acrylic blocks and had their roots partially covered with acrylic resin, leaving 2-mm root surfaces exposed. Toothbrushing was performed for 35,000 and 65,000 double-strokes. Specimens were analyzed using non-contact profilometry for dental volume loss (mm3) and lesion morphology. Data was analyzed using ANOVA with pairwise comparisons and Kruskal-Wallis tests.
The two-way interaction between toothbrush head configuration and slurry abrasivity was significant (p = 0.02). At 35,000 strokes, the flat-trimmed and cross-angled/multilevel/rubbers added toothbrushes caused the highest loss, when associated to the high-abrasive slurry (p<0.05); whereas cross-angled/multilevel/flex head showed the least loss, when associated to the low-abrasive (p<0.05). At 65,000, more dental loss was observed for all toothbrushes when associated to the high-abrasive slurry, with flat-trimmed causing the highest loss (p < 0.05). Lower dental loss rates were observed for cross-angled/multilevel/flex head associated to the low-abrasive slurry when compared to the other toothbrushes (p < 0.05), except to feathered (p = 0.14) and rippled (p = 0.08). Flat lesions (mean internal angle ± standard-deviation: 146.2°± 16.8) were mainly associated with low-abrasive slurry, while wedge-shaped lesions (85.8°± 18.8) were more frequent with medium- and high-abrasive slurries.
The development, progression and morphology of simulated NCCLs were modulated by both toothbrush head configuration and dentifrice abrasivity.
Dental professionals should consider both the type of toothbrush and dentifrice abrasivity in the management plan of patients at risk of developing NCCLs.