Bone tissue exhibits self-healing properties; however, not all defects can be repaired without surgical intervention. Bone tissue engineering offers artificial scaffolds, which can act as a temporary matrix for bone regeneration. The aim of this study was to manufacture scaffolds made of poly(lactic acid), poly(ε-caprolactone), poly(propylene fumarate), and poly(ethylene glycol) modified with bioglass, beta tricalcium phosphate (TCP), and/or wollastonite (W) particles. The scaffolds were fabricated using a gel-casting method and observed with optical and scanning electron microscopes. Attenuated total reflectance-Fourier transform infrared (ATR-FTIR), differential scanning calorimetry (DSC), thermogravimetry (TG), wettability, and degradation tests were conducted. The highest content of TCP without W in the composition caused the highest hydrophilicity (water contact angle of 61.9 ± 6.3°), the fastest degradation rate (7% mass loss within 28 days), moderate ability to precipitate CaP after incubation in PBS, and no cytotoxicity for L929 cells. The highest content of W without TCP caused the highest hydrophobicity (water contact angle of 83.4 ± 1.7°), the lowest thermal stability, slower degradation (3% mass loss within 28 days), and did not evoke CaP precipitation. Moreover, some signs of cytotoxicity on day 1 were observed. The samples with both TCP and W showed moderate properties and the best cytocompatibility on day 4. Interestingly, they were covered with typical cauliflower-like hydroxyapatite deposits after incubation in phosphate-buffered saline (PBS), which might be a sign of their excellent bioactivity.

Binary blends of polyterpenes are employed comprising cis-1,4-polyfarnesene (PF) with a bottlebrush architecture, and linear cis-1,4-polyisoprene (PI) as model systems toward supersoft polymer melts. The bottlebrush PF results in a low plateau modulus ( G N 0 ≈ 3.5 × 10 4 ${G}_{N}^{0}\\approx 3.5\\ensuremath{\\times{}}{10}^{4}$ Pa) that can further be reduced with the addition of PI. Depending on the fraction of short PI chains in the athermal and nearly isofrictional blends, plateau moduli in the range from 1 to 10 kPa can be achieved. Tube dilation is very efficient in the present binary blends as compared to more common blends comprising long/short or linear/star chains of identical polymer structure.

In this study, the synthesis of poly(AVGVP) [where A-Alanine, V-Valine, G-Glycine, and P-Proline] is executed by the stepwise solution phase method. The interaction between Chitosan and synthetic polypentapeptide in blends was examined in the liquid and solid phases. Viscosity criteria that establish the total miscibility with Chitosan are the Δ[η]m, the intrinsic viscosity [η], Huggins coefficient [KH], by Garcia ΔB, α by Sun, and μ suggested by Chee, ΔK, and β buttressed by Jiang and Han. Besides, the results are corroborated in the solid phase by differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and X-ray diffraction (XRD). Miscibility in the blends led to higher thermal stability than that of pure polymers, according to thermogravimetric analysis (TGA). In vitro, studies offered the absence of cytotoxicity, and in vivo histopathological results advocated that the blend shows less inflammation and is more compact as against cotton gauge, evincing an enhanced healing environment and promising the possibility of use in wound therapeutic applications.

Maintaining a high modulus to simultaneously withstand deformation and increase fatigue resistance to restrict crack propagation in a material presents a significant challenge. In this work, a straightforward strategy was developed to address this issue in polymers. A dynamic network was incorporated into a permanent one prior to the formation of the latter, and two incompatible polymer networks were created to prevent common phase separation. The mechanical and fatigue resistance properties were substantially enhanced by the exact modulation of the soft and hard phase distribution by precise control over the densities of dynamic and permanent networks as well as the number of reprocessing steps. The experimental results demonstrated a nearly 9-fold increase in the fatigue life of polyurethane compared with traditional design methods and a 2.5 times increase in modulus. This strategy shows potential for the design of fatigue-resistant thermosetting and thermoplastic materials. The results offer new insight into the development of durable, high-performance materials that are reprocessable and compatible.

This study aims to use beeswax, a readily available and cost-effective organic material, as a novel phase change material (PCM) within blends of low-density polyethylene (LDPE) and styrene-b-(ethylene-co-butylene)-b-styrene (SEBS). LDPE and SEBS act as support materials to prevent beeswax leakage. The physicochemical properties of new blended phase change materials (B-PCM) were determined using an X-ray diffractometer and an infrared spectrometer, confirming the absence of a chemical reaction within the materials. A scanning electron microscope was used for microstructural analysis, indicating that the interconnection of the structure allowed better thermal conductivity. Thermal gravimetric analysis revealed enhanced thermal stability for the B-PCM when combined with SEBS, especially within its operating temperature range. Analysis of phase change temperature and latent heat with differential scanning calorimetry showed no major difference in the melting point of the various PCM blends created. During the melting/solidification process, the B-PCMs possess excellent performance as characterized by W70/P30 (112.45 J.g-1) > W70/P20/S10 (94.28 J.g-1) > W70/P10/S20 (96.21 J.g-1) of latent heat storage. Additionally, the blends tend to reduce supercooling compared to pure beeswax. During heating and cooling cycles, the B-PCM exhibited minimal leakage and degradation, especially in blends containing SEBS. In comparison to the rapid temperature drop observed during the cooling process of W70/P30, the temperature decline of W70/P30 was slower and longer, as demonstrated by infrared thermography. The addition of LDPE to the PCM reduced melting time, indicating an improvement in the thermal energy storage reaction time to the demand. According to the obtained findings, increasing the SEBS concentration in the composite increased the thermal stability of the resulting PCM blends significantly. Despite the challenges mentioned earlier, SEBS proved to be an effective encapsulating material for beeswax, whereas LDPE served well as a supporting material. Leak tests were performed to find the ideal mass ratio, and weight loss was analyzed after multiple cycles of cooling and heating at 70 °C. The morphology, thermal characteristics, and chemical composition of the beeswax/LDPE/SEBS composite were all examined. Beeswax proves to be a highly effective phase change material for storing thermal energy within LDPE/SEBS blends.

Polymer blends of poly(L-lactide)-b-poly(ethylene glycol)-b-poly(L-lactide) (PLLA-PEG-PLLA) and high-density polyethylene (HDPE) with different blend ratios were prepared by a melt blending method. The thermal, morphological, mechanical, opacity, and biodegradation properties of the PLLA-PEG-PLLA/HDPE blends were investigated and compared to the PLLA/HDPE blends. The blending of HDPE improved the crystallization ability and thermal stability of the PLLA-PEG-PLLA; however, these properties were not improved for the PLLA. The morphology of the blended films showed that the PLLA-PEG-PLLA/HDPE blends had smaller dispersed phases compared to the PLLA/HDPE blends. The PLLA-PEG-PLLA/HDPE blends exhibited higher flexibility, lower opacity, and faster biodegradation and bioerosion in soil than the PLLA/HDPE blends. Therefore, these PLLA-PEG-PLLA/HDPE blends have a good potential for use as flexible and partially biodegradable materials.

Poly(L-Lactide) (PLA), a fully biobased aliphatic polyester, has attracted significant attention in the last decade due to its exceptional set of properties, such as high tensile modulus/strength, biocompatibility, (bio)degradability in various media, easy recyclability and good melt-state processability by the conventional processes of the plastic/textile industry. Blending PLA with other polymers represents one of the most cost-effective and efficient approaches to develop a next-generation of PLA-based materials with superior properties. In particular, intensive research has been carried out on PLA-based blends with engineering polymers such as polycarbonate (PC), poly(ethylene terephthalate) (PET), poly(butylene terephthalate) (PBT) and various polyamides (PA). This overview, consequently, aims to gather recent works over the last 10 years on these immiscible PLA-based blends processed by melt extrusion, such as twin screw compounding. Furthermore, for a better scientific understanding of various ultimate properties, processing by internal mixers has also been ventured. A specific emphasis on blend morphologies, compatibilization strategies and final (thermo)mechanical properties (tensile/impact strength, ductility and heat deflection temperature) for potential durable and high-performance applications, such as electronic parts (3C parts, electronic cases) to replace PC/ABS blends, has been made.

Additive manufacturing (AM) enables the production of complex, lightweight, and customized components with superior quality. Selecting the right materials considering their thermal properties, printability, and layer adhesion is crucial in melting-based AM techniques. This study investigates Droplet Deposition Modelling (DDM), an innovative material extrusion process that utilizes thermoplastic granules. DDM is distinguished by its shorter manufacturing times and a wider range of materials, setting it apart from traditional material extrusion methods such as fused filament fabrication. We investigated the printability and part quality in DDM using two common pharmaceutical excipients: Polyvinylpyrrolidone/vinyl acetate 6:4 (PVP/VA), which is highly brittle, and Polycaprolactone (PCL), known for its low solubility and role in controlled drug release. Different ratios of PVP/VA and PCL were compounded via hot melt extrusion (HME) and used in DDM to study the impact of ingredient content on printability and part quality, employing geometrical models to assess material compatibility and printability. The study revealed that increasing PVP/VA content leads to higher viscosity, reduced flowability, and uneven deposition, with formulations of 80 % and 100 % PVP/VA showing poor processability. In contrast, formulations with 60 % and 40 % PVP/VA exhibited smooth processing and compatibility with DDM. We identified processing temperature and Drop Aspect Ratio (DAR) as key factors influencing material printability and part quality. Elevated processing temperatures and reduced DAR were found to increase interface temperatures, reduce diffusion, and potentially cause the \'elephant feet\' issue. Additionally, smaller droplet sizes and material characteristics, such as higher interfacial tension in PCL, could lead to coalescence. Our findings highlight the complexities in optimizing DDM processing parameters and material blends, underscoring the need for careful formulation design to achieve high-quality 3D printed products.

A Monte Carlo study of the compatibilization of A/B polymer blends has been performed using the bond fluctuation model. The considered compatibilizers are copolymer molecules composed of A and B blocks. Different types of copolymer structures have been included, namely, linear diblock and 4-block alternating copolymers, star block copolymers, miktoarm stars, and zipper stars. Zipper stars are composed of two arms of diblock copolymers arranged in alternate order (AB and BA) from the central unit, along with two homogeneous arms of A and B units. The compatibilization performance has been characterized by analyzing the equilibration of repulsion energy, the simulated scattering intensity obtained with opposite refractive indices for A and B, the profiles along a coordinate axis, the radial distribution functions, and the compatibilizer aggregation numbers. According to the results, linear alternate block copolymers, star block copolymers, and zipper stars exhibit significantly better compatibilization, with zipper stars showing slightly but consistently better performance.

Two dynamic covalent networks based on the Diels-Alder reaction were blended to exploit the properties of the dissimilar polymer backbones. Furan-functionalized polyether amines based on poly(propylene oxide) (PPO) FD4000 and polydimethylsiloxane (PDMS) FS5000 were mixed in a common solvent and reversibly cross-linked with the same bismaleimide DPBM. The morphology of the phase-separated blends is primarily controlled by the concentration of backbones. Increasing the PDMS content of the blends results in a dilute droplet morphology at 25 wt %, with a growing size and concentration of droplets and the formation of two separate PPO- and PDMS-rich layers at 50 wt %. Further increasing the PDMS content to 75 wt % leads to larger droplets and a thicker layer of the secondary phase. The hydrophobic PDMS phase creates a barrier against water, while the more hydrophilic PPO phase enhances the resistance against oxygen diffusion. Lowering the maleimide-to-furan stoichiometric ratio resulted in a decrease in cross-link density and thus more flexible and stretchable encapsulants. Changes in the stoichiometric ratio also affected the phase morphology due to resulting changes in phase separation and network formation kinetics. Lowering the stoichiometric ratio also resulted in enhanced self-healing properties of 96% at room temperature as a consequence of the increased chain mobility in the blended networks. The self-healing blends were used to encapsulate liquid metal circuits to create stretchable strain sensors with a linear electro-mechanical response without much drift or hysteresis, which could be efficiently recovered by 90% after the damage-healing cycles.