Zwitterionic sulfobetaine-based monolithic stationary phases have attracted increasing attention for their use in hydrophilic interaction chromatography. In this study, a novel hydrophilic polymeric monolith was fabricated through photo-initiated copolymerization of 3-(3-vinyl-1-imidazolio)-1-propanesulfonate (SBVI) with pentaerythritol triacrylate using methanol and tetrahydrofuran as the porogenic system. Notably, the duration for the preparation of this novel monolith was as little as 5 min, which was significantly shorter than that required for previously reported sulfobetaine-based monoliths prepared via conventional thermally initiated copolymerization. Moreover, these monoliths showed good morphology, permeability, porosity (62.4%), mechanical strength (over 15 MPa), column efficiency (51,230 plates/m), and reproducibility (relative standard deviations for all analytes were lower than 4.6%). Mechanistic studies indicated that strong hydrophilic and negative electrostatic interactions might be responsible for the retention of polar analytes on the zwitterionic SBVI-based monolith. In particular, the resulting monolith exhibited good anti-protein adhesion ability and low nonspecific protein adsorption. These excellent features seem to favor its application in bioanalysis. Therefore, the novel zwitterionic sulfobetaine-based monolith was successfully employed for the highly selective separation of small bioactive compounds and the efficient enrichment of N-glycopeptides from complex samples. In this study, we prepared a novel zwitterionic sulfobetaine-based monolith with good performance and developed a simpler and faster method for preparation of zwitterionic monoliths.

This work demonstrates a cross-linkable zwitterionic polymer, the corresponding zwitterionic thermosetting resin, and their application for antifouling surface coating. The tertiary amine-containing benzoxazine group is utilized as a precursor to react with 1,3-propane sultone to introduce sulfobetaine moiety to benzoxazine group. The reaction route provides an effective approach for preparation of sulfobetaine-functionalized benzoxazines and the corresponding sulfobetaine-functionalized thermosetting resins of benzoxazines. The sulfobetaine-functionalized polybenzoxazine has been utilized as a coating material for ceramic porous membranes to impart protein-repelling characteristic to the membrane surface. In a filtration test on a Bovine serum albumin (BSA) aqueous solution, the sulfobetaine resin modified membrane shows a 96.2% of rejection rate and a 1680 ± 9 Lm2-h-1 of permeation flux at the first cycle test. In cycled measurements with membrane washing, the membrane shows a total flux decline ratio (Rt) and a reversible flux decline ratio (Rr) of about 46.9% and 43.1%, respectively. A high ratio of reversible fouling (Rr/Rt) of 91.9% is found, which supports the statement that the sulfobetaine-functionalized polybenzoxazine is an effective material to impart antifouling characteristic to porous materials for bioseparation and filtration.

Work function engineering of two-dimensional (2D) materials by application of polymer coatings represents a research thrust that promises to enhance the performance of electronic devices. While polymer zwitterions have been demonstrated to significantly modify the work function of both metal electrodes and 2D materials due to their dipole-rich structure, the impact of zwitterion chemical structure on work function modulation is not well understood. To address this knowledge gap, we synthesized a series of sulfobetaine-based zwitterionic random copolymers with variable substituents and used them in lithographic patterning for the preparation of negative-tone resists (i.e., \"zwitterists\") on monolayer graphene. Ultraviolet photoelectron spectroscopy indicated a significant work function reduction, as high as 1.5 eV, induced by all polymer zwitterions when applied as ultrathin films (<10 nm) on monolayer graphene. Of the polymers studied, the piperidinyl-substituted version, produced the largest dipole normal to the graphene sheet, thereby inducing the maximum work function reduction. Density functional theory calculations probed the influence of zwitterion composition on dipole orientation, while lithographic patterning allowed for evaluation of surface potential contrast via Kelvin probe force microscopy. Overall, this polymer \"zwitterist\" design holds promise for fine-tuning 2D materials electronics with spatial control based on the chemistry of the polymer coating and the dimensions of the lithographic patterning.

For efficient and effective utilization of MXene such as biosensing or advanced applications, interfacial modification of MXene needs to be considered. To this end, we describe modification of Ti3C2Tx MXene by aryldiazonium-based grafting with derivatives bearing a sulfo- (SB) or carboxy- (CB) betaine pendant moiety. Since MXene contains free electrons, betaine derivatives could be grafted to MXene spontaneously. Kinetics of spontaneous grafting of SB and CB toward MXene was electrochemically examined in two different ways, and such experiments confirmed much quicker spontaneous SB grafting compared to spontaneous CB grafting. Moreover, a wide range of electrochemical methods investigating non-Faradaic and Faradaic redox behavior also in the presence of two redox probes together with contact-angle measurements and secondary ion mass spectrometry (SIMS) confirmed substantial differences in formation and interfacial presentation of betaine layers, when spontaneously grafted on MXene. Besides spontaneous grafting of CB and SB toward MXene, also electrochemical grafting by a redox trigger was performed. Results suggest that electrochemical grafting provides a denser layer of SB and CB on the MXene interface compared to spontaneous grafting of SB and CB. Moreover, an electrochemically grafted SB layer offers much lower interfacial resistance and an electrochemically active surface area compared to an electrochemically grafted CB layer. Thus, by adjusting the SB/CB ratio in the solution during electrochemical grafting, it is possible to effectively tune the redox behavior of an MXene-modified interface. Finally, electrochemically grafted CB and SB layers on MXene were evaluated against non-specific protein binding and compared to the anti-fouling behavior of an unmodified MXene interface.

Films of zwitterionic polymers are increasingly explored for conferring fouling resistance to materials. Yet, the structural diversity of polyzwitterions is rather limited so far, and clear structure-property relationships are missing. Therefore, we synthesized a series of new polyzwitterions combining ammonium and sulfate groups in their betaine moieties, so-called poly(sulfabetaine)s. Their chemical structures were varied systematically, the monomers carrying methacrylate, methacrylamide, or styrene moieties as polymerizable groups. High molar mass homopolymers were obtained by free radical polymerization. Although their solubilities in most solvents were very low, brine and lower fluorinated alcohols were effective solvents in most cases. A set of sulfabetaine copolymers containing about 1 mol % (based on the repeat units) of reactive benzophenone methacrylate was prepared, spin-coated onto solid substrates, and photo-cured. The resistance of these films against the nonspecific adsorption by two model proteins (bovine serum albumin-BSA, fibrinogen) was explored, and directly compared with a set of references. The various polyzwitterions reduced protein adsorption strongly compared to films of poly(nbutyl methacrylate) that were used as a negative control. The poly(sulfabetaine)s showed generally even somewhat higher anti-fouling activity than their poly(sulfobetaine) analogues, though detailed efficacies depended on the individual polymer-protein pairs. Best samples approach the excellent performance of a poly(oligo(ethylene oxide) methacrylate) reference.

In this study, we show that codeposition of temperature responsive microgels in the foulant cake layer and cleaning of the cake upon stimuli-induced size change of the microgels is an effective method of fouling removal. Humic acid in CaCl2 solution was used as a model foulant and poly( n-isopropylacrylamide) (p(NIPAm)) and poly( n-isopropylacrylamide- co-sulfobetainemethacrylate) (p(NIPAm- co-SBMA)) were used as temperature responsive microgels. Filtrations were done below the lower critical solution temperature (LCST) and temperature was increased to above the LCST for cleaning. As an extra cleaning a temperature swing of above, below and then again above the LCST was applied. P(NIPAm) was found to be ineffective in cleaning the foulant deposit despite the 20-fold change in its volume with temperature change at LCST. P(NIPAm- co-SBMA) microgels, on the other hand, provided high fouling reversibility on hydrophilic poly(ether sulfone)(PES)/poly(vinylpyrrolidone) (PVP) and hydrophobic PES membranes. Better fouling reversibility with these microgels was observed at low and high solution ionic strength. While the use of microgels alone increased fouling reversibility to some extent, even in the absence of temperature stimulus, 100% reversibility could only be obtained when a temperature switch was applied in the presence of microgels, showing the effect of microgels\' volume change in cleaning.

暂无摘要。

Micron- and nano-sized particles are extensively used in various biomedical applications. However, their performance is often drastically hampered by the nonspecific adsorption of biomolecules, a process called biofouling, which can cause false-positive and false-negative outcomes in diagnostic tests. Although antifouling coatings have been extensively studied on flat surfaces, their use on micro- and nanoparticles remains largely unexplored, despite the widespread experimental (specifically, clinical) uncertainties that arise because of biofouling. Here, we describe the preparation of magnetic micron-sized beads coated with zwitterionic sulfobetaine polymer brushes that display strong antifouling characteristics. These coated beads can then be equipped with recognition elements of choice, to enable the specific binding of target molecules. First, we present a proof of principle with biotin-functionalized beads that are able to specifically bind fluorescently labeled streptavidin from a complex mixture of serum proteins. Moreover, we show the versatility of the method by demonstrating that it is also possible to functionalize the beads with mannose moieties to specifically bind the carbohydrate-binding protein concanavalin A. Flow cytometry was used to show that thus-modified beads only bind specifically targeted proteins, with minimal/near-zero nonspecific protein adsorption from other proteins that are present. These antifouling zwitterionic polymer-coated beads, therefore, provide a significant advancement for the many bead-based diagnostic and other biosensing applications that require stringent antifouling conditions.

Imaged capillary isoelectric focusing (icIEF) separates ampholytic components of biomolecules in an electric field according to their isoelectric points and has been used for protein charge variants quantification and characterization. Denaturants are ordinarily incorporated into icIEF to stabilize charge species in solution. In certain circumstances, however, denaturants are detrimental to stable isoelectric separation of proteins due to their unique structural and biophysical features, such as an aggregation-prone antibody we encountered recently. Here we report our novel matrix formula non-detergent sulfobetaine and taurine (NDSB-T). It is deprived of denaturants that notably ameliorates the assay robustness and peak resolution for this antibody. NDSB-T is a combination of non-detergent sulfobetaine (NDSB) and taurine possessing the stabilization and separation power while maintaining protein integrity. As a result, assay throughputs are tremendously increased for more than 10 folds along with extraordinarily improved assay accuracy. Furthermore, NDSB-T can separate and quantify protein charge species in native state and therefore avoid partial denaturation derived peaks which are often misleading and hard to characterize. NDSB-T may be a valuable tool for proteins incompatible with conventional icIEF matrices and potentially opens a new window for icIEF assay in native conditions.

We aimed to introduce hydrophilic sulfobetaine-type zwitterionic groups to macromolecular chains of copolymers to construct novel copolymer hydrogels with anti-protein-fouling performance that could be used as soft contact lens (SCL) materials. Using hydroxyethyl methacrylate (HEMA), N-vinyl pyrrolidinone (NVP) and sulfobetaine methacrylate (SBMA) as comonomers, several copolymer hydrogels with different SBMA contents, poly(HEMA-NVP-SBMA), are synthesized via radical copolymerization in an aqueous phase. Surface chemistry, structural morphologies, water contact angle (WCA), equilibrium water content (EWC), visible light transmittance and tensile mechanical properties are investigated. The prepared hydrogels exhibit a closed-type porous structure. With increasing SBMA content in the comonomer mixture, the prepared copolymer hydrogel pore size gradually increases up to the micron level, WCA tends to decrease, EWC tends to increase, and visible light transmittance slightly increases, but their tensile mechanical properties decline. The amounts of protein Lyz and BSA adsorbed on the copolymer hydrogels and on commercially available EASY DAY® SCLs as a control are also determined by protein adsorption tests. The amount of protein adsorbed on the copolymer hydrogel decreases with increasing SBMA content. For the hydrogel prepared using the comonomer mixture with 5.0 wt % SBMA, the amount of adsorbed Lyz is 0.91 μg/cm2, which corresponds to only 56.8% of the amount adsorbed on EASY DAY® SCLs. Thus, novel SCL materials with high water content and excellent anti-protein-fouling performance were efficiently constructed by introducing sulfobetaine-type zwitterionic groups into a traditional polymer hydrogel system.