UNASSIGNED: To compare the biomechanical parameters of microplates and the combined miniplate-microplate for fixing zygomaticomaxillary complex (ZMC) fractures using nonlinear finite element analysis (FEA).
UNASSIGNED: Two samples of ZMC fracture models were prepared. In sample 1 (S1), the fractures were stabilized with microplates, and in sample 2 (S2), with miniplates plus microplates. FEA software was used to measure the displacement, Von Mises stress distribution (VMSD), and maximum principal stress distribution (MPSD).
UNASSIGNED: The displacement was 6.7 μm in the L-shaped plate of both samples, 4.4 μm in the S1 lateral-edge plate, 4.8 μm in the S2 lateral-edge plate, 5.8 μm in the S1 bottom-edge plate, and 5.6 μm in the S2 bottom-edge plate. The VMSD was 41.1 MPa in the S1 lateral-edge plate, 24.3 MPa in the S2 lateral-edge plate, 7.6 MPa in the S1 Lshaped plate, 9.6 MPa in S2 L-shaped plate, 28.5 MPa in the S1 bottom-edge plate, and 11.8 MPa in the S2 bottom-edge plate. The MPSD was 46.2 MPa in the S1 lateral-edge plate, 26.4 MPa in the S2 lateral-edge plate, 3.6 MPa in S1 L-shaped plate, 4.2 MPa in S2 L-shaped plate, 30.9 MPa in S1 bottom-edge plate, and 14.1 MPa in the S2 bottom-edge plate.
UNASSIGNED: The L-shaped and lateral-edge plates in both samples had the highest and lowest amount of displacement, respectively. The lateral-edge plates in both samples had the highest VMSD and MPSD, which was higher in S1 than S2. The L-shaped plate had the lowest VMSD and MPSD in both samples.

Background/Objectives: The use of miniplates for stabilizing bones post orthognathic surgery has surged in popularity due to their efficacy in ensuring stability and hastening recovery. However, controversy exists regarding what should be done with these miniplates after surgery. Some surgeons advocate for their removal, while others suggest leaving them in place. This study sought to assess the frequency, causes, and potential risk factors linked with miniplate removal in orthognathic procedures. Methods: A thorough meta-analysis was conducted by scrutinizing studies from various databases including PubMed, Google Scholar, Embase, and Scopus, focusing on publications spanning from 1989 to 2023. Results: Ten studies meeting the inclusion criteria, encompassing 1603 patients, were chosen for inclusion in the meta-analysis. The male-to-female ratio varied from 0.7:1 to 4:1. Overall, 5595 miniplates were inserted, with 294 (5.3%) being subsequently removed. Primary reasons for miniplate removal included infection (161 cases, 2.9%), exposure of miniplates (34 cases, 0.6%), and palpable plates (23 cases, 0.4%). Other indications comprised pain, patient preference, and temperature sensitivity. Less frequent causes for miniplate removal included sinusitis, secondary surgery, and dental pathology. The mean duration of miniplate removal was 5.5 months, with the majority (56.1%) being removed from the mandible rather than the maxilla. In conclusion, this meta-analysis underscores the importance of miniplate removal when hardware causes complications and physical discomfort. The primary reasons for removing miniplates were infection and plate exposure, with the mandible being the most common removal site. Conclusions: These findings emphasize the need for continued monitoring to assess the fate of miniplates in orthognathic surgery and provide valuable information for future clinical decision-making.

: A three-dimensional-printed individual titanium plate was applied for maxillary protraction to eliminate side effects and obtain the maximum skeletal effect. This study aimed to explore the stress distribution characteristics of sutures during maxillary protraction using individual titanium plates in various directions and locations.
: A protraction force of 500 g per side was applied at forward and downward angles between 0° and 60° with respect to the Frankfort horizontal plane, after which the titanium plate was moved 2 and 4 mm upward and downward, respectively. Changes in sutures with multiple protraction directions and various miniplate heights were quantified to analyze their impact on the maxillofacial bone.
: Protraction angle of 0-30° with respect to the Frankfort horizontal plane exhibited a tendency for counterclockwise rotation in the maxilla. At a 40° protraction angle, translational motion was observed in the maxilla, whereas protraction angles of 50-60° tended to induce clockwise rotation in the maxilla. Enhanced protraction efficiency at the lower edge of the pyriform aperture was associated with increased height of individual titanium plates.
: Various protraction directions are suitable for patients with different types of vertical bone surfaces. Furthermore, when the titanium plate was positioned lower, the protraction force exhibited an increase.

This case report documents the diagnosis and successful management of a substantial periapical lesion located in the lower left region of the jaw. The patient presented with clinical symptoms indicative of periapical pathology, and radiographic examination revealed an extensive radiolucent lesion. The chosen treatment approach involved endodontic intervention coupled with surgical decompression, leading to the resolution of the lesion and restoration of oral health. This case underscores the significance of an accurate diagnosis and a multidisciplinary treatment approach in addressing large periapical lesions.

UNASSIGNED: Fifty patients were included to compare the efficacy of three-dimensional (3D) locking miniplates versus 3D standard miniplates in the management of mandibular fractures.
UNASSIGNED: Fifty patients were randomly allocated to either 3D locking miniplate group or 3D standard miniplate group. All patients were followed for six months to compare post-operative occlusion, stability and associated clinical complications such as wound dehiscence, infection and plate/screw fracture and mental nerve paraesthesia.
UNASSIGNED: All the fractures were adequately fixed when checked intraoperatively. Four patients in each group had mildly deranged occlusion, one patient in Group A and two patients in Group B had reduced stability. None of the patients had complications of non-union or malunion. In Group A, one out of 25 patients had mental nerve paraesthesia and two had wound dehiscence. Moreover, in Group B, two patients had mental nerve paraesthesia and two others had wound dehiscence. The data when compared were statistically significant (=0.05).
UNASSIGNED: The overall result of our study led us to the conclusion that both the plating systems were satisfactory and there is no statistically significant difference when used for open reduction and fixation in mandibular fractures. Healing was satisfactory in both groups.

UNASSIGNED: Mandible is the only mobile facial jaw bone and it aides in various functions such as phonation and mastication. Therefore, management of mandible fracture becomes inevitable due to its functional and anatomical importance. Fracture fixation methods and techniques have steadily evolved with various osteosynthesis systems. In this article, we discuss the management of mandible fracture using a newly designed two-dimensional (2D) hybrid V-shaped plate.
UNASSIGNED: In this paper, we have evaluated the efficacy of the newly developed 2D V-shaped locking plate in the management of mandibular fractures.
UNASSIGNED: We have assessed 12 cases of different mandibular fractures ranging from symphysis, parasymphysis, angle and subcondylar region. Treatment outcome was assessed both clinically and radiologically at regular intervals with various intraoperative and postoperative parameters.
UNASSIGNED: Results of this study suggest that fixation of mandible fracture with the 2D hybrid V-shaped plate facilitates anatomic reduction and functional stability and carries a low morbidity and infection rate.
UNASSIGNED: The 2D anatomic hybrid V-shaped plate can be a suitable alternative to conventional miniplate and 3D plates as it offers satisfactory anatomic reduction and functional stability. Positioning the plate in relation to the mental nerve and plate adaptation along the angle region are much easier.

UNASSIGNED: The present study compared the stability of fracture fragments in the management of bilateral parasymphysis mandible fracture with Miniplate fixation and Reconstruction plate fixation using finite element analysis.
UNASSIGNED: 3D FE Mandible model was created using CT scanner. Two bilateral parasymphysis mandible fracture models were created. Model 1 was fixed with Miniplates, and Model 2 was fixed with Reconstruction plate. Loading forces of 120 N at molar region and 62.5 N at incisor region were applied. These two models were imported to ANSY\'S Workbench Software.
UNASSIGNED: Miniplate fixation model showed comparatively reduced gap between fragments than Reconstruction plate. But the gap values of both the models were within the physiologic limit of healing under this specific loading. Analytically Miniplates were superior to Reconstruction plate in the management of bilateral parasymphysis fracture.
UNASSIGNED: Analytically Miniplates are superior to Reconstruction plate in the management of bilateral parasymphysis fracture. As the masticatory forces were reduced during fracture healing period, both fixations provide satisfactory healing. So both Miniplate and Reconstruction plate can be considered as fixation method for bilateral parasymphysis mandible fracture.

Due to their advantages in applicability, patient-specific (CAD/CAM) reconstruction plates are increasingly used in fibula free flap mandible reconstruction. In addition, recently, CAD/CAM miniplates, with further advantages in postoperative management, have been introduced. However, biomechanical conditions induced by CAD/CAM systems remain partially unknown. This study aimed to evaluate the primary fixation stability of CAD/CAM fixators. For a patient-specific scenario, the biomechanical conditions induced in a one segmental fibula free flap stabilized using either a CAD/CAM reconstruction plate or CAD/CAM miniplates were determined using finite element analysis. The main output parameters were the strains between intersegmental bone surfaces and stresses in the fixation systems due to different biting scenarios. CAD/CAM miniplates resulted in higher mechanical strains in the mesial interosseous gap, whereas CAD/CAM reconstruction plate fixation resulted in higher strains in the distal interosseous gap. For all investigated fixation systems, stresses in the fixation systems were below the material yield stress and thus material failure would not be expected. While the use of CAD/CAM miniplates resulted in strain values considered adequate to promote bone healing in the mesial interosseous gap, in the distal interosseous gap CAD/CAM reconstruction plate fixation might result in more beneficial tissue straining. A mechanical failure of the fixation systems would not be expected.

UNASSIGNED: Surgical management of mandibular symphysis and parasymphysis fractures has evolved from rigid fixation to semi-rigid fixation with miniplate osteosynthesis. Various miniplate systems have been developed in recent years including three-dimensional miniplate, microplates and bioresorbable plate, and their advantages and disadvantages have been compared and studied. To overcome the shortcomings of 3D plating system such as difficulty in adaptation and fixation in fractures involving the mental nerve, a novel Z plate has been designed by our institute.
UNASSIGNED: An in vitro study was performed to evaluate the biomechanical behaviour of the newly designed Z plate with 3D plate and two-miniplate system using finite element analysis.
UNASSIGNED: Our study showed total structural deformation of 0.17 mm and 0.31 mm of newly designed Z plate after canine loading and molar loading, respectively. The equivalent von Mises force for plate after canine loading had shown the following results-Z plate showed values of 121.3 MPa and 58.40 MPa after molar loading.
UNASSIGNED: Our study concluded that the Z plate produces lowest stresses, lesser total structural deformation, superior stability and support in comparison with the 3D plate and two-miniplate system.

UNASSIGNED: Fracture fixation, in the present times, is classically done using mini plates. The position and number of plates to fixate a mandibular angle fracture have been and are still extensively researched and reported in the literature. A more recent addition is 3D mini plates.
UNASSIGNED: To compare and evaluate the biomechanical behavior of one 2.0 mm titanium 3D miniplate fixation plate (4- hole) and one 2.0 mm titanium 4-hole miniplate in internal fixation of mandibular angle fractures.
UNASSIGNED: To measure load at break, maximum load, and displacement at maximal load for internal fixation done with 3D mini plates and conventional mini plates respectively.
UNASSIGNED: Five dry cadaveric mandibles were sectioned into 10 hemi-mandibles. Each cadaveric mandible was sectioned at the angle of mandible to simulate unfavorable mandibular angle fracture. The obtained hemimandible were divided into experimental groups (GROUP 1 and GROUP 2) with 5 samples in each group, plated with a linear miniplate and 3D miniplate respectively. Maximal load, Load at break, and displacement at maximum load were the only obtained parameters for comparison.
UNASSIGNED: Conventional miniplate showed greater mean maximum load values of 174.93 N±54.45 compared to 3D mini plates which recorded a mean maximum load value of 106.96 N ± 23.86. Load at break and displacement at maximum load were found to be both insignificant.
UNASSIGNED: The results in this study showed statistically no significant difference with any of the above parameters except maximal load, between the two groups evaluated. Conventional linear miniplate according to Champy\'s lines of osteosynthesis can be used successfully for providing satisfactory osteosynthesis with the definitive advantage of cost-effectiveness.