In this paper, a new method involving a wear-resistant and reusable template is proposed for the preparation of high-mechanical-strength superhydrophobic polymer film based on wire electrical discharge machining (WEDM). A solid-liquid-contact-angle simulation model was established to obtain surface-texture types and sizes that may achieve superhydrophobicity. The experimental results from template preparation show that there is good agreement between the simulation and experimental results for the contact angle. The maximum contact angle on the template can reach 155.3° given the appropriate triangular surface texture and WEDM rough machining. Besides, the prepared superhydrophobic template exhibits good wear resistance and reusability. PDMS superhydrophobic polymer films were prepared by the template method, and their properties were tested. The experimental results from the preparation of superhydrophobic polymer films show that the maximum contact angle of the polymer films can be up to 154.8° and that these films have good self-cleaning and anti-icing properties, wear resistance, bending resistance, and ductility.

The intricate composition of wastewater impedes the recycling of agricultural and industrial effluents. This study aims to investigate the potential of sisal leaf wastewater (SLW), both water-treated (WTSLW) and alkali-treated (ATSLW), as a substitute for the alkali activator (NaOH solution) in the production of slag-powder- and fly-ash-based composites, with a focus on the effects of WTSLW substitution ratios and sisal leaf soaking durations. Initially, the fresh properties were assessed including electrical conductivity and fluidity. A further analysis was conducted on the influence of both WTSLW and ATSLW on drying shrinkage, density, and mechanical strength, including flexural and compressive measures. Microstructural features were characterized using SEM and CT imaging, while XRD patterns and FTIR spectra were employed to dissect the influence of WTSLW substitution on the composite\'s products. The results show that incorporating 14 wt% WTSLW into the composite enhances 90-day flexural and compressive strengths by 34.8% and 13.2%, respectively, while WTSLW curtails drying shrinkage. Conversely, ATSLW increases porosity and decreases density. Organic constituents in both WTSLW and ATSLW encapsulated in the alkaline matrix fail to modify the composites\' chemical composition. These outcomes underscore the potential for sustainable construction materials through the integrated recycling of plant wastewater and solid by-products.

As one of the raw materials of basic magnesium sulfate cement (BMSC), the activity of light-burned magnesium oxide (MgO) has an important effect on the hydration rate, hydration products, and mechanical properties of BMSC. To reveal the influence of packaging method, storage environment, and storage time on the activity of MgO and the mechanical properties of BMSC, an experiment was conducted by using ordinary woven bags, peritoneal woven bags, and plastic and paper compound bags to store the finished BMSC and the raw materials (light-burned MgO, MgSO4·7H2O, fly ash, and a chemical additive) under the conditions of natural environment, sealed environment, and wet environment, respectively. Comparative analysis of the effects of packaging method, storage conditions, and storage time on the activity of MgO and the mechanical properties of BMSC was performed through the mechanical strength test of mortar specimens. The results showed that in a sealed environment, the loss of a-MgO content in light-burned MgO was minimized, which was more conducive to keeping the mechanical properties of BMSC stable. In the wet environment, the mechanical strength of BMSC was significantly reduced in the early stage (1 day) due to the significant reduction in the activity of MgO, and the mechanical strength of the finished BMSC and prepared BMSC after 120 days of storage was still lost, regardless of the packaging method. However, the storage environment and packaging method had relatively little effect on the late mechanical strength (28 days) of BMSC. It is advisable to use ordinary woven bags for packaging in natural and sealed environments as this is more economical for engineering applications. Plastic and paper compound bags are superior to ordinary woven bags and peritoneal woven bags in wet environments.

Mandibular reconstructive surgery is necessary for large bone defects. Although various reconstruction methods have been performed clinically, there is no mandibular reconstruction method that meets both sufficient strength criteria and the patient\'s specific morphology. In this study, the material strength of the cylindrical lattice structures formed by electron-beam melting additive manufacturing using titanium alloy powder was investigated for mandibular reconstruction. The virtual strengths of 28 lattice structures were compared using numerical material tests with finite element method software. Subsequently, to compare the material properties of the selected structures from the preliminary tests, compression test, static bending test and fatigue test were conducted. The results showed that there were correlations with relative density and significant differences among the various structures when comparing internal stress with deformation, although there was a possibility of localized stress concentration and non-uniform stress distribution based on the lattice structure characteristics. These results suggest that the lattice structure of body diagonals with nodes and a cell size of 3.0 mm is a potential candidate for metallic artificial mandibles in mandibular reconstruction surgery.

This research aimed to produce eco-friendly straws using soy protein isolate (SPI) and cassava starch (CS) at different ratios by the extrusion technique and by coating with beeswax and shellac wax. Three straw formulations (F) (F1: 24.39% SPI-24.39% CS; F2: 19.51% SPI-29.37% CS; and F3: 14.63% SPI-34.15% CS) were prepared, incorporating glycerol (14.6% w/w) and water (36.6% w/w). After extrusion and drying at 80 °C for 20 h, visual assessment favored F2 straws due to smoother surfaces, the absence of particles, and enhanced straightness. For the physical property test, the straws were softened in pH buffer solutions for 5 min. To simulate practical application, mechanical bending strength was studied under different relative humidity (RH) settings. Water absorption reduced the strength as RH increased. F2 straws outperformed other formulations in bending strength at 54% RH. For hydrophobic coatings, F2 was chosen. Beeswax- and shellac wax-coated straws displayed negligible water absorption and sustained their integrity for over 6 h compared to uncoated straws. This study shows that extrusion and natural coatings may make sustainable straws from SPI and CS. These efforts help meet the growing demand for eco-friendly plastic alternatives, opening up new options for single-use straws.

Fibers crystallize and become brittle at high temperatures for a long time, so the surface coating must maintain long-lasting emission performance, which requires superior antioxidant properties of the high-emissivity fillers. To improve the radiation performance of the coating and the tensile strength of the fiber fabric, a double-layer coating with high emissivity was prepared on the surface of flexible aluminum silicate fiber fabric (ASFF) using MoSi2 and SiC as emissive agents. The incorporation of borosilicate glass into the outer coating during high-temperature oxidation of ZrB2 results in superior encapsulation of emitter particles, effectively filling the pores of the coating and significantly reducing the oxidation rate of MoSi2 and SiC. Furthermore, the addition of an intermediate ZrO2 layer enhances the fiber bundle\'s toughness. The obtained double-coated ASFF exhibits an exceptionally high tensile strength of 57.6 MPa and a high bond strength of 156.2 kPa. After being subjected to a 3 h heating process, the emissivity exhibits a minimal decrease of only 0.032, while still maintaining a high value above 0.9. The thermal insulation composites, consisting of a flexible ASFF matrix and a ZrB2-modified double-layer coating, exhibit significant potential for broad applications in the field of thermal protection.

Autologous-engineered artificial tissues constitute an ideal alternative for radical surgery in terms of natural anticoagulation, self-repair, tissue regeneration, and the possibility of growth. Previously, we focused on the development and practical application of artificial tissues using \"in-body tissue architecture (iBTA)\", a technique that uses living bodies as bioreactors. This study aimed to further develop iBTA by fabricating tissues with diverse shapes and evaluating their physical properties. Although the breaking strength increased with tissue thickness, the nominal breaking stress increased with thinner tissues. By carving narrow grooves on the outer periphery of an inner core with narrow grooves, we fabricated approximately 2.2 m long cord-shaped tissues and net-shaped tissues with various designs. By assembling the two inner cores inside the branched stainless-steel pipes, a large graft with branching was successfully fabricated, and its aortic arch replacement was conducted in a donor goat without causing damage. In conclusion, by applying iBTA technology, we have made it possible, for the first time, to create tissues of various shapes and designs that are difficult using existing tissue-engineering techniques. Thicker iBTA-induced tissues exhibited higher rupture strength; however, rupture stress was inversely proportional to thickness. These findings broaden the range of iBTA-induced tissue applications.

The high demand for lithium (Li) relates to clean, renewable storage devices and the advent of electric vehicles (EVs). The extraction of Li ions from aqueous media calls for efficient adsorbent materials with various characteristics, such as good adsorption capacity, good selectivity, easy isolation of the Li-loaded adsorbents, and good recovery of the adsorbed Li ions. The widespread use of metal-based adsorbent materials for Li ions extraction relates to various factors: (i) the ease of preparation via inexpensive and facile templation techniques, (ii) excellent selectivity for Li ions in a matrix, (iii) high recovery of the adsorbed ions, and (iv) good cycling performance of the adsorbents. However, the use of nano-sized metal-based Lithium-ion sieves (LISs) is limited due to challenges associated with isolating the loaded adsorbent material from the aqueous media. The adsorbent granulation process employing various binding agents (e.g., biopolymers, synthetic polymers, and inorganic materials) affords composite functional particles with modified morphological and surface properties that support easy isolation from the aqueous phase upon adsorption of Li ions. Biomaterials (e.g., chitosan, cellulose, alginate, and agar) are of particular interest because their structural diversity renders them amenable to coordination interactions with metal-based LISs to form three-dimensional bio-composite materials. The current review highlights recent progress in the use of biopolymer binding agents for the granulation of metal-based LISs, along with various crosslinking strategies employed to improve the mechanical stability of the granules. The study reviews the effects of granulation and crosslinking on adsorption capacity, selectivity, isolation, recovery, cycling performance, and the stability of the LISs. Adsorbent granulation using biopolymer binders has been reported to modify the uptake properties of the resulting composite materials to varying degrees in accordance with the surface and textural properties of the binding agent. The review further highlights the importance of granulation and crosslinking for improving the extraction process of Li ions from aqueous media. This review contributes to manifold areas related to industrial application of LISs, as follows: (1) to highlight recent progress in the granulation and crosslinking of metal-based adsorbents for Li ions recovery, (2) to highlight the advantages, challenges, and knowledge gaps of using biopolymer-based binders for granulation of LISs, and finally, (3) to catalyze further research interest into the use of biopolymer binders and various crosslinking strategies to engineer functional composite materials for application in Li extraction industry. Properly engineered extractants for Li ions are expected to offer various cost benefits in terms of capital expenditure, percent Li recovery, and reduced environmental footprint.

Over the last 20 years, flue gas desulfurization gypsum (FGD gypsum) has become a valuable and widely used substitute for a natural raw material to produce plasters, mortars, and many other construction products. The essential advantages of FGD gypsum include its high purity and stability, which allow for better technical parameters compared to natural gypsum, and, until recently, its low price and easy availability. This FGD gypsum is obtained in the process of desulfurization of flue gases and waste gases in power plants, thermal power plants, refineries, etc., using fossil fuels such as coal or oil. The gradual reduction in energy production from fossil raw materials implemented by European Union countries until its complete cessation in 2049 in favor of renewable energy sources significantly affects the availability of synthetic gypsum, and forces producers of mortars and other construction products to look for new solutions. The gypsum content in commonly used light plaster mortars is usually from 50 to 60% by mass. This work presents the results of tests on mortars wherein the authors reduced the amount of gypsum to 30%, and, to meet the strength requirements specified in the EN 13279-1:2008 standard, added Portland cement in the amount of 6-12% by mass. Such a significant reduction in the content of synthetic gypsum will reduce this raw material\'s consumption, thus extending its availability and developing other solutions. The study presented the test results on strength, density, porosity, pore size distribution, and changes in the microstructure of mortars during up to 180 days of maturation in conditions of increased relative humidity. The results show that decreased porosity and increased mechanical strength occur due to the densification of the microstructure caused by the formation of hydration products, such as C-S-H, ettringite, and thaumasite.

In this article, ABA triblock copolymer (tri-BCP) thermoplastic elastomers with poly(ethylene oxide) (PEO) middle block and polyzwitterionic poly(4-vinylpyridine) propane-1-sulfonate (PVPS) outer blocks were synthesized. The PVPS-b-PEO-b-PVPS tri-BCPs were doped with lithium bis-(trifluoromethane-sulfonyl) imide (LiTFSI) and used as solid polyelectrolytes (SPEs). The thermal properties and microphase separation behavior of the tri-BCP/LiTFSI hybrids were studied. Small-angle X-ray scattering (SAXS) results revealed that all tri-BCPs formed asymmetric lamellar structures in the range of PVPS volume fractions from 12.9% to 26.1%. The microphase separation strength was enhanced with increasing the PVPS fraction (fPVPS) but was weakened as the doping ratio increased, which affected the thermal properties of the hybrids, such as melting temperature and glass transition temperature, to some extent. As compared with the PEO/LiTFSI hybrids, the PVPS-b-PEO-b-PVPS/LiTFSI hybrids could achieve both higher modulus and higher ionic conductivity, which were attributed to the physical crosslinking and the assistance in dissociation of Li+ ions by the PVPS blocks, respectively. On the basis of excellent electrical and mechanical performances, the PVPS-b-PEO-b-PVPS/LiTFSI hybrids can potentially be used as solid electrolytes in lithium-ion batteries.