The abuse and irrational use of tetracyclines (TCs) in human medicine and animal husbandry has become a serious concern, affecting the ecological environment and human health. The aim of this study was to develop a sensitive and selective method using fully automatic solid-phase extraction coupled with ultra-performance liquid chromatography-tandem mass spectrometry for the determination of twelve TCs in water. Four isotope-labeled internal standards for TCs were used to correct matrix effects. Several parameters affecting extraction efficiency were systematically optimized, and the optimum experimental conditions found were 1.0 L water sample with 0.5 g/L Na2EDTA (pH 3.0) extracted and enriched by CNW HLB cartridge and eluted by 4 mL of acetone:methanol (v/v, 1:1). The enrichment factors were up to 798-1059 but only requiring about 60 min per six samples. Under the optimized conditions, the linearity of the method ranged from 0.2 to 100 μg/L for 12 TCs, the detection limits were as low as 0.01-0.15 ng/L, and the recoveries were in the range of 70%-118%, with relative standard deviations less than 15%. The developed method can be successfully utilized for the determination of 12 TCs in pure water, tap water, river water, and mariculture seawater. In summary, three and six TCs were detected in river water and mariculture seawater, respectively, with total concentrations of 0.074-0.520 ng/L (mean 0.248 ng/L) and 0.792-58.369 ng/L (12.629 ng/L), respectively. Tetracycline (TC) and oxytetracycline (OTC) were the dominant TCs in river water, while doxytetracycline (DXC) and OTC were dominant in mariculture seawater.

Mercury (Hg) emitted from East Asian has increased the risk of Hg in China Marginal Seas for decades. However, the speciation of Hg (especially the bioavailable Hg) in these regions remains unclear. To address this problem, we analyzed total Hg (THg) and methylmercury (MeHg) in the sediment and porewater of Yellow sea (YS) and East China Sea (ECS) and determined the speciation of Hg using both improved BCR sequential extraction and isotope dilution (ID) techniques. Nearshore areas of YS and ECS exhibited higher THg levels in sediments and porewater, suggesting the significant contribution of terrestrial inputs. The spatial distribution of MeHg showed similar trends with THg, but the sites with higher MeHg concentrations did not align with those of THg. The improved BCR sequential extraction method showed the residual fraction dominated Hg content (∼44 %) in both systems, with a minor bioavailable carbonate fraction (1 %). The Spearman correlation analysis indicates that Eh and pH are the two factors significantly affected Hg bioavailability in the sediment. The bioavailability of Hg (estimated by the BCR method) showed a significant positive correlation with MeHg levels in the sediment (R²=0.47, P < 0.05), suggesting that BCR can be used to estimate the potential of Hg methylation in the sediment. However, the extent of bioavailable Hg in BCR and ID method were 1.15 ± 0.38 % and 29.5 ± 14.8 %, respectively, implying that Hg bioavailability may be underestimated by BCR techniques compared to ID methods (T-test, P < 0.01).

OBJECTIVE: The standardization of cystatin C (CysC) measurement has received increasing attention in recent years due to its importance in estimating glomerular filtration rate (GFR). Mass spectrometry-based assays have the potential to provide an accuracy base for CysC measurement. However, a precise, accurate and sustainable LC-MS/MS method for CysC is still lacking.
METHODS: The developed LC-MS/MS method quantified CysC by detecting signature peptide (T3) obtained from tryptic digestion. Stable isotope labeled T3 peptide (SIL-T3) was spiked to control matrix effects and errors caused by liquid handling. The protein denaturation, reduction and alkylation procedures were combined into a single step with incubation time of 1 h, and the digestion lasted for 3.5 h. In the method validation, digestion time-course, imprecision, accuracy, matrix effect, interference, limit of quantification (LOQ), carryover, linearity, and the comparability to two routine immunoassays were evaluated.
RESULTS: No significant matrix effect or interference was observed with the CysC measurement. The LOQ was 0.21 mg/L; the within-run and total imprecision were 1.33-2.05 % and 2.18-3.90 % for three serum pools (1.18-5.34 mg/L). The LC-MS/MS method was calibrated by ERM-DA471/IFCC and showed good correlation with two immunoassays traceable to ERM-DA471/IFCC. However, significant bias was observed for immunoassays against the LC-MS/MS method.
CONCLUSIONS: The developed LC-MS/MS method is robust and simpler and holds the promise to provide an accuracy base for routine immunoassays, which will promote the standardization of CysC measurement.

Safrole oxide (SAFO), a metabolite of naturally occurring hepatocarcinogen safrole, is implicated in causing DNA adduct formation. Our previous study first detected the most abundant SAFO-induced DNA adduct, N7-(3-benzo[1,3] dioxol-5-yl-2-hydroxypropyl)guanine (N7γ-SAFO-G), in mouse urine using a well-developed isotope-dilution high-performance liquid chromatography-electrospray ionization tandem mass spectrometry (ID-HPLC-ESI-MS/MS) method. This study further elucidated the genotoxic mode of action of SAFO in mice treated with SAFO 30, 60, 90, or 120 mg/kg for 28 days. The ID-HPLC-ESI-MS/MS method detected N7γ-SAFO-G with excellent sensitivity and specificity in mouse liver and urine of SAFO-treated mice. Our data provide the first direct evidence of SAFO-DNA adduct formation in rodent tissues. N7γ-SAFO-G levels in liver were significantly increased by SAFO 120 mg/kg compared with SAFO 30 mg/kg, suggesting rapid spontaneous or enzymatic depurination of N7γ-SAFO-G in tissue DNA. Urinary N7γ-SAFO-G exhibited a sublinear dose response. Moreover, the micronucleated peripheral reticulocyte frequencies increased dose-dependently and significantly correlated with N7γ-SAFO-G levels in liver (r = 0.8647; p < 0.0001) and urine (r = 0.846; p < 0.0001). Our study suggests that safrole-mediated genotoxicity may be caused partly by its metabolic activation to SAFO and that urinary N7γ-SAFO-G may serve as a chemically-specific cancer risk biomarker for safrole exposure.

Isotope dilution (ID) analysis is considered one of the most accurate quantitative methods. However, it has not been widely applied to the quantitative imaging of trace elements in biological samples using laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS), mainly because of difficulties in homogeneously mixing enriched isotopes (the spike) with the sample (e.g., a tissue section). In this study, we present a novel method for the quantitative imaging of trace elements (copper and zinc) in mouse brain sections using ID-LA-ICP-MS. We used an electrospray-based coating device (ECD) to evenly distribute a known amount of the spike (65Cu and 67Zn) on the sections. The optimal conditions for this process involved evenly distributing the enriched isotopes on mouse brain sections mounted on indium tin oxide (ITO) glass slides using the ECD with the 10 mg g-1 ɑ-cyano-4-hydroxycinnamic acid (CHCA) in methanol at 80 °C. The mass of the spiked isotopes and the tissue sections on the ITO slides was calculated by weighing them on an analytical balance. Quantitative images of Cu and Zn in Alzheimer\'s disease (AD) mouse brain sections were obtained using ID-LA-ICP-MS. These imaging results showed that Cu and Zn concentrations in various brain regions typically ranged from 10 to 25 μg g-1 and 30-80 μg g-1, respectively. But it is worth noting that the hippocampus contained up to 50 μg g-1 of Zn, while the cerebral cortex and hippocampus had Cu contents as high as 150 μg g-1. These results were validated by acid digestion and solution analysis with ICP-MS. The novel ID-LA-ICP-MS method provides an accurate and reliable means for quantitative imaging of biological tissue sections.

The large-scale use of sulfonamide antimicrobials in human and veterinary medicine has seriously endangered the ecological environment and human health. The objective of this study was to develop and validate a simple and robust method for the simultaneous determination of seventeen sulfonamides in water using ultra-high performance liquid chromatography-tandem mass spectrometry coupled with fully automated solid-phase extraction. Seventeen isotope-labeled internal standards for sulfonamides were used to correct matrix effects. Several parameters affecting extraction efficiency were systematically optimized, and the enrichment factors were up to 982-1033 and only requiring about 60 min per six samples. Under the optimized conditions, this method manifested good linearity (0.05-100 μg/L), high sensitivity (detection limits: 0.01-0.05 ng/L), and satisfactory recoveries (79-118%) with acceptable relative standard deviations (0.3-14.5%, n = 5). The developed method can be successfully utilized for the determination of 17 sulfonamides in pure water, tap water, river water, and seawater. In total, six and seven sulfonamides were detected in river water and seawater, respectively, with a total concentration of 8.157-29.676 ng/L and 1.683-36.955 ng/L, respectively, and sulfamethoxazole was the predominant congener.

A new and accurate method using resin enrichment of Ga, combined with isotope dilution, was developed to determine its dissolved concentrations in natural waters. The extraction properties of Chelex-100, Nobias Chelate PA-1, and Presep® PolyChelate resins for Ga from river water and seawater were compared. Experiments were conducted to determine the optimal pH range, capacity to eliminate matrix and interference, extraction and elution times, and ideal quantity of resin beads. The Chelex-100 resins were determined to be inferior to the other resins in their ability to remove the matrix and interference. The properties of Nobias Chelate PA-1 and Presep® PolyChelate were comparable, whereas Presep® PolyChelate resins were ultimately chosen for sample analysis owing to their wide range for extracting Ga at low pHs compared to Nobias Chelate PA-1 resins. The optimal isotope dilution conditions for Ga concentration measurements in natural water are discussed. The procedural blank of the method was 0.42 ± 0.18 pmol/kg (N = 12, 1 SD) and the detection limit was 0.6 pmol/kg. Intercalibration samples of GS were analyzed, with results of 41.6 ± 1.06 pmol/kg (N = 6, 1 SD), which agreed with previously reported data. Other intercalibration samples (GSP, GSC, NASS-6, NASS-7, SAFe D1, and SAFe D2) were also measured. The Ga, sampled using the contamination-free X-Vane method and conventional CTD rosette samplers, were compared and showed no statistical difference. Ga concentrations in different natural waters were determined. The Ga concentrations in rainwater were extremely low, whereas those in river water and seawater were in good agreement with existing knowledge.

In this study, a gas chromatography-mass spectrometry (GC-MS) method was established for the determination of zearalenone and its five derivatives in feed, including zearalanone, α-zearalanol, β-zearalanol, α-zearalenol, and β-zearalenol. An effective immunoaffinity column was prepared for sample purification, which was followed by the silane derivatization of the eluate after an immunoaffinity chromatography analysis for target compounds by GC-MS. Matrix effects were corrected by an isotope internal standard of zearalenone in this method. The six analytes had a good linear relationship in the range of 2-500 ng/mL, and the correlation coefficients were all greater than 0.99. The limits of detection (LODs) and limits of quantification (LOQs) were less than 1.5 μg/kg and 5.0 μg/kg, respectively. The average spike recoveries for the six feed matrices ranged from 89.6% to 112.3% with relative standard deviations (RSDs) less than 12.6%. Twenty actual feed samples were analyzed using the established method, and at least one target was detected. The established GC-MS method was proven to be reliable and suitable for the determination of zearalenone and its derivatives in feed.

We aimed to compare fluid status as determined by multifrequency bioimpedance spectroscopy (MF-BIS, Xitron 4200, USA) with that determined by the isotope dilution method among a contemporary Chinese cohort. Healthy Chinese subjects (HS, n = 30) were recruited in Zhengzhou. Hemodialysis (HD, n = 49) and peritoneal dialysis (PD, n = 48) patients were screened at the First Affiliated Hospital of Zhengzhou University. Total body water (TBW) and extracellular water (ECW) were measured by deuterium (TBWD) and bromide (ECWBr) dilution, respectively, and by MF-BIS using the Moissl equation (ME). The results of MF-BIS were compared to the reference method by Pearson analysis and Bland-Altman analysis in the three groups. The accuracy of overhydration as determined by MF-BIS was analyzed by receiver operating characteristic (ROC) curves. The TBWD and TBWME values were 34.67 ± 7.31 and 35.41 ± 5.76 L, 37.30 ± 8.58 and 37.02 ± 8.10 L, and 38.61 ± 10.02 and 38.44 ± 7.59 L in the HS, HD and PD groups, respectively. The ECWBr and ECWME values were 14.88 ± 3.33 and 15.53 ± 2.39 L, 16.24 ± 5.08 and 16.90 ± 3.93 L, and 19.08 ± 6.41 and 18.23 ± 3.61 L in the HS, HD and PD groups, respectively. The mean bias between TBWD and TBWME was -0.74 L, 0.28 L, and 0.17 L in the HS, HD and PD groups, respectively. The mean bias between ECWBr and ECWME was -0.65 L, -0.66 L, and 0.85 L in the HS, HD and PD groups, respectively. Compared to the ECWBr/TBWD ratio, the area under the ROC curve (AUC) of the ECWME/TBWME ratio for the diagnosis of overhydration was 0.76 and 0.68 in the HD and PD groups, respectively. In summary, MF-BIS with ME could be used in Chinese HD and PD patients.

To investigate the effects of acetate, propionate, and pH on thermodynamics of volatile fatty acids (VFA) in the rumen, a dual-flow continuous culture study was conducted to quantify production of major VFA, interconversions among the VFA, and H2 and CH4 emissions in a 4 × 4 Latin square design. The 4 treatments were (1) control: pH buffered to an average of 6.75; (2) control plus 20 mmol/d of infused acetate (InfAc); (3) control plus 7 mmol/d of infused propionate (InfPr); and (4) a 0.5-unit decline in pH elicited by adjustment of the buffer (LowpH). All fermentors were fed 40 g of a pelleted diet containing whole alfalfa pellets and concentrate mix pellets (50:50) once daily. After 7 d of treatment, sequential, continuous infusions of [2-13C] sodium acetate (3.5 mmol/d), [U-13C] sodium propionate (2.9 mmol/d), and [1-13C] sodium butyrate (0.22 mmol/d) were carried out from 12 h before feeding for 36 h. Filtered liquid effluent (4 mL) was sampled at 0, 2, 4, 6, 8, 12, 16, and 22 h after feeding, and assessed for VFA concentrations, with another filtered sample (20 mL) used to quantify aqueous concentrations of CH4 and H2. Headspace CH4 and H2 gases were monitored continuously. Ruminal microbes were isolated from the mixed effluent samples, and the microbial community structure was analyzed using the 16S rRNA amplicon sequencing technique. The digestibility of neutral detergent fiber, acid detergent fiber, and starch and microbial C sequestrated from VFA were not affected by treatments. The LowpH treatment increased net propionate production and decreased H2 and CH4 headspace emissions, primarily due to shifts in metabolic pathways of VFA formation, likely due to the observed changes in bacterial community structure. Significant interconversions occurred between acetate and butyrate, whereas interconversions of other VFA with propionate were relatively small. The InfAc and InfPr treatments increased net acetate and propionate production, respectively; however, interconversions among VFA were not affected by pH, acetate, or propionate treatments, suggesting that thermodynamics might not be a primary influencer of metabolic pathways used for VFA formation.