This investigation is dedicated to unlocking the hidden potential of discarded cosmetics towards building green sustainable road pavements in the future. It is particularly aiming at exploring waste lipstick (WLS) as a high-quality functional additive for advanced asphalt mix technologies. To fuel this novel innovation, the effect of various WLS doses (e.g., 5, 10, and 15 wt.%) on the performance of base AP-5 asphalt cement was studied in detail. A wide array of cutting-edge analytical lab techniques was employed to inspect in-depth the physicochemical, microstructural, thermo-morphological, and rheological properties of resultant admixtures including: elemental analysis, Fourier transform-infrared spectroscopy (FT-IR), X-ray diffraction (XRD), thin-layer chromatography-flame ionization detection (TLC-FID), scanning electron microscopy (SEM), atomic force microscopy (AFM), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), needle penetration, ring and ball softening point, Brookfield viscometer, ductility, and dynamic shear rheometer (DSR) tests. Unlike the unstable response of asphaltenes, the additive/artificial aging treatments increased the fraction of resins the most, and decreased that of aromatics; however, asphaltenes did not impair the saturates portion, according to Iatroscan research. FT-IR scan divulged that the WLS-asphalt interaction was physical rather than chemical. XRD diagnosis not only revealed an obvious correlation between the asphaltenes content and the fresh-binder crystallinity but also revealed the presence of fillers in the WLS, which may generate outstanding technical qualities to bituminous mixes. According to AFM/SEM analyses, the stepwise incorporation of WLS grew the magnitude of the \"bee-shaped\" microstructures and extended the roughness rate of unaged/aged binders. The prolonged consumption of the high thermal-stable additive caused a remarkable drop in the onset degradation and glass transition temperature of mixtures, thus enhancing their workability and low-temperature performance, according to TGA/DTGA/DSC data. The DSR and empirical rheological experiments demonstrated that the WLS could effectively lower the manufacturing and compaction temperatures of asphalt mixes and impart them with valuable anti-aging/fatigue-cracking assets. In a nutshell, the use of waste lipstick as an asphalt modifier is viable and cost-effective and could attenuate the pollution arisen from the beauty sector, while improving the performance of hot/warm asphalt mixes (HAM/WAM) and extending the service life of roadways.

Polysaccharide ubiquity is trimmed for applications of low syneresis impact. This syneresis may be crucial for specific applications that are very sensitive to gel dimension stability, namely, 3D scaffolds for cell culture for disease diagnosis and tissue engineering. We hypothesized that the syneresis origin results from the kappa-carrageenan (kC) polysaccharide thermodynamic instability, and we demonstrated this by measuring the critical (coil-to-coil contact) concentration as a function of temperature. The impact of 5 mM, 10 mM and 15 mM KCl salt on the critical concentration of the solution and the lower critical concentration temperature (LCCT) were particularly investigated. For the kC polysaccharide, the gelation temperature (Tg) falls at temperatures below the LCCT, which explains the shrinking or syneresis reaction of the polysaccharide gels. The gap between Tg and LCCT would be the thermomotive force of the syneresis of many colloidal gels.

Semisolids constitute a significant proportion of topical pharmaceutical dosage forms available on the market, with creams being considered profitable systems for releasing active substances into the skin. This work aimed at the development of a generic Clotrimazole topical cream, based on the assumptions that assist the development of such formulations. First, the critical parameters to obtain a final formulation as similar as possible to the reference product were defined. Then, the percentages of cetyl palmitate and octyldodecanol were identified as critical variables and chosen for optimization in further studies. A \"quality by design\" approach was then used to identify the effect of process variability on the structural and functional similarity (Q3) of the generic product qualitatively (Q1) and quantitatively (Q2). A two-factor central composite orthogonal design was applied and eleven different formulations were developed and subjected to physicochemical characterization and product performance studies. The results were used to estimate the influence of the two variables in the variation of the responses, and to determine the optimum point of the tested factors, using a design space approach. Finally, an optimized formulation was obtained and analysed in parallel with the reference. The obtained results agreed with the prediction of the chemometric analysis, validating the reliability of the developed multivariate models. The in vitro release and permeation results were similar for the reference and the generic formulations, supporting the importance of interplaying microstructure properties with product performance and stability. Lastly, based on quality targets and response constraints, optimal working conditions were successfully achieved.

Natural biopolymer-based hydrogels especially agarose and collagen gels, considering their biocompatibility with cells and their capacity to mimic biological tissues, have widely been used for in-vitro experiments and tissue engineering applications in recent years; nevertheless their mechanical properties are not always optimal for these purposes. Regarding the importance of the mechanical properties of hydrogels, many mechanical characterization studies have been carried out for such biopolymers. In this work, we have focused on understanding the mechanical role of agarose and collagen concentration on the hydrogel strength and elastic behavior. In this direction, Amirkabir Magnetic Bead Rheometry (AMBR) characterization device equipped with an optimized electromagnet, was designed and constructed for the measurement of hydrogel mechanical properties. The operation of AMBR set-up is based on applying a magnetic field to actuate magnetic beads in contact with the gel surface in order to actuate the gel itself. In simple terms the magnetic beads leads give rise to mechanical shear stress on the gel surface when under magnetic influence and together with the associated bead-gel displacement it is possible to calculate the hydrogel shear modulus. Agarose and Collagen gels with respectively 0.2-0.6 wt % and 0.2-0.5 wt % percent concentrations were prepared for mechanical characterization in terms of their shear modulus. The shear modulus values for the different percent concentrations of the agarose gel were obtained in the range 250-650 Pa, indicating the shear modulus increases by increasing in the agar gel concentration. In addition to this, the values of shear modulus for the collagen gel increase as function of concentration in the range 240-520 Pa in accordance with an approximately linear relationship between collagen concentration and gel strength.

With the increasing debate on sustainability, there is a strong market trend to formulate more sustainable products for topical application. Several studies emphasize the potential applications of natural, organic, or green chemistry-derived ingredients, but comparative studies between conventional ingredients and sustainable alternatives are lacking. This type of study is considered an excellent baseline and time-saving strategy for future studies. In addition, one of the main challenges of replacing ingredients by sustainable alternatives in topical vehicles is to maintain high-quality products. Thus, the main goal of this research study was to create a well-defined strategy supported by specific experimental data for the development of sustainable topical vehicles with high-quality standards. The study was designed to evaluate the effects of replacing conventional ingredients (e.g., hydrocarbons, silicones, and preservatives) by sustainable ones on the physical, chemical, and microbiological features of topical emulsions. Additionally, in vivo assessment studies were performed to evaluate the safety, biological efficacy, and sensorial aspects of the developed formulations. The results obtained showed that the replacement of ingredients by sustainable alternatives has an effective impact on the physicochemical and structural properties of the emulsions, mainly on their rheological behavior. However, using appropriate strategies for ingredient selection and rheological adjustment, it is possible to overcome some barriers created by the use of natural raw materials, thus developing appealing and high-quality sustainable topical vehicles.

This study investigated the effects of drug recrystallization on the in vitro performance of testosterone drug-in-adhesive transdermal delivery system (TDS). Six formulations were prepared with a range of dry drug loading in the adhesive matrix from 1% to 10% w/w with the aim of generating TDS with various levels of drug crystals. We visually quantified the amount of crystals in TDS by polarized light microscopy. The effect of drug recrystallization on adhesion, tackiness, cohesive strength, viscoelasticity, drug release, and drug permeation through human cadaver skin were evaluated for these TDS samples. The Optical images showed no crystals in 1% and 2% testosterone TDSs; however, the amount of crystals increased by increasing testosterone loading from 4 to 10%. A proportional and significant decrease (p < 0.05) in tack, peel, and shear strength of the adhesive matrix with increasing amount of crystals in TDS was observed. The drug crystals resulted in a proportional deterioration of the viscoelastic properties of the adhesive matrix. The 2% testosterone TDS showed faster drug release rate when compared to 1% testosterone TDS. The increase in drug loading from 2% to 4% w/w slightly increased the cumulative amount of testosterone released. Further increase in drug loading in TDS to 6, 8, and 10% was nonsignificant (p > 0.05) to affect the drug release and permeation. In conclusion, this study demonstrated that the extent of drug recrystallization can be quantitatively correlated with the deterioration of performance characteristics of TDS products.

Objective: The main objective of this work was to evaluate the performance of recently developed dynamic-mechanical thermoanalysis (DMTA) test as a rapid rheological alternative to conventional freeze-thaw cycling for accelerated stability testing of oil-in-water (O/W) emulsions.Significance: The rational for this approach was reducing the time needed for product and process development and optimization, potentially through shortening the time needed for stability evaluation, in order to keep the pace with high formulating turnover imposed by increasing demands for placing products on the market, that is, to facilitate decision making in R&D and QC settings.Methods: Six model O/W emulsions were designed, rheologically characterized (continuous rotational and oscillatory tests), and subjected to stability evaluation through freeze-thaw test in stability chamber and DMTA tests using an air-bearing rheometer.Results: Investigated samples were characterized by favorized shear-thinning flow behavior with yield point. The elastic behavior dominated the viscous one in the LVE region of amplitude sweeps, as well as in the frequency sweeps of used frequency range. Statistical method comparison studies demonstrated that the results obtained by freeze-thaw test, routinely used for accelerated stability testing of emulsions, were in good accordance with those obtained with DMTA tests, whereas the time needed for stability assessment was significantly reduced (2-6 h versus 12 days).Conclusions: In summary, DMTA test proved to be an expeditious alternative for accelerated freeze-thaw stability testing of O/W emulsions, with great promise in new product development and optimization (R&D), as well as in determination of borderline product batches status (QC).

Some rheological, thermodynamic and functional properties of selected hydrocolloids (xanthan gum-cress seed gum (XG-CSG)) blends at different ratios (1-0, 3-1, 1-1, 1-3, 0-1) were characterized to understand physically the biopolymers interaction and networks. XG showed a greater rigidity (elastic modulus, G\'LVE = 58.60 Pa), total structural strength (complex modulus, G*LVE = 70.69 Pa), yield stress (limiting value of stress, τL = 7.58 Pa), emulsion capacity (EC = 6.78%) and foam stability (FC = 18.92%) than CSG (G\'LVE = 7.05 Pa, G*LVE = 8.53 Pa, τL = 1.44 Pa, EC = 86.48% and FC = 14.98%), respectively. Among blends, 3-1 XG-CSG showed the highest G*LVE, foaming stability (FS) and the extent of recovery (Rr%). The results were summarized using the clustering technique and principal component analyses. The coefficient of the interaction of some parameters, Cole-Cole plots and Gibbs free energy changes (ΔG) of predisturbed and intact networks were investigated. In samples with an intact network, greater compatibility directly related to the extent of synergistic interaction, while in predisturbed samples, the lower compatibility directly related to the extent of synergistic interaction. Although all blends were highly incompatible with antagonistic behavior, 1-1 XG-CSG showed the lowest incompatibility (ΔG = 8028.60 J/mol) among samples with intact structure, while at disrupted state, 1-3 XG-CSG showed the lowest incompatibility (ΔG = 158.6 J/mol).

Curcumin is a polyphenolic compound found in turmeric (Curcuma longa) rhizome that has potential biological benefits, including antioxidant, antimicrobial, anti-inflammatory, and anti-cancer activity. Incorporation of curcumin into functional food and beverage products, however, is challenging due to its low water-solubility, poor chemical stability, rapid metabolism, and low oral bioavailability. Researchers are, therefore developing a suite of particle-based delivery systems to maximize the potential health benefits of curcumin. Colloidal delivery systems, such as micelles, microemulsions, nanoemulsions, emulsions, solid lipid nanoparticles, nanostructured lipid carriers, biopolymer nanoparticles, and microgels have all been developed for this purpose. The functional performance of each of these delivery systems depends on its structure and physicochemical properties, such as particle composition, particle size, morphology, physicochemical stability, optical properties, rheology, and sensory attributes. As a result, each delivery system has its advantages and disadvantages for particular applications. Consequently, a delivery system must be specifically designed for the particular bioactive agent to be encapsulated, as well as the particular food matrix it will be incorporated into. In this review, we highlight the potential of the Delivery by Design (DbD) approach for identifying and selecting the most appropriate colloidal delivery system for a particular food application, using curcumin as a model bioactive agent.

Stable and efficient conjugates between antibodies and gold nanoparticles (GNP-Ab) are sought to develop highly sensitive and robust biosensors with applications in medicine, toxicology, food safety controls, and targeted drug delivery. Several strategies have been proposed for directing the antibody attachment to GNPs thus preserving antibody activity, including covalently coupling the antibody to a polymer grafted on GNP surface and exploiting the high affinity of bioreceptors as mediators for the binding. Both approaches also allow for shielding GNPs with a protective layer that guarantees the robustness of the conjugate. Notwithstanding, antibodies freely adsorb to GNP with high binding efficiency. The nonspecific adsorption is far more simple, fast, and inexpensive than any mediated coupling. Therefore, it is preferred for most applications, although it is considered to produce GNP-Ab with a limited activity. In this work, we compared three strategies for producing GNP-Ab, such as (i) covalent coupling mediated by a chemical layer, (ii) affinity-based binding mediated by a biomolecular layer composed of Staphylococcal protein A, and (iii) direct attachment via adsorption. The so-prepared GNP-Ab were employed as probes in a colorimetric lateral flow immunoassay (LFIA) for measuring salivary cortisol as a model biosensor that relies on the use of active GNP-Ab conjugates. Unexpectedly, the biosensors fabricated using the three probes were completely comparable in terms of their ability to measure salivary cortisol. Furthermore, we observed that the sensitivity of the LFIA primarily depended on the amount of the antibody bound to GNPs rather than on the method by which it was bound. The probes prepared using both the direct adsorption approach and mediated coupling via the biochemical mediator enabled development of point-of-care devices for the fast, sensitive, and reliable measurement of human salivary cortisol.