This study is a preliminary investigation exploring the mechanical properties of three-dimensional (3D)-printed personalized mesh titanium alloy prostheses and the feasibility of repairing hemi-mandibular defects. The ANSYS 14.0 software and selective laser melting (SLM) were used to produce personalized mesh titanium alloy scaffolds. Scaffolds printed using different parameters underwent fatigue property tests and scanning electron microscopy (SEM) of the fracture points. Models of hemi-mandibular defects (encompassing the temporomandibular joint) were created using beagle dogs. Freeze-dried allogeneic mandibles or 3D-printed personalized mesh titanium alloy prostheses were used for repair. Gross observation, computed tomography (CT), SEM, and histological examinations were used to compare the two repair methods. The prostheses with filament diameters of 0.5 and 0.7 mm could withstand 14,000 times and >600,000 cycles of alternating stresses, respectively. The truss-structure scaffold with a large aperture and large aperture ratio could withstand roughly 250,000 cycles of alternating forces. The allogeneic mandible graft required intraoperative shaping, while the 3D-printed mesh titanium alloy prostheses were personalized and did not require intraoperative shaping. The articular disc on the non-operated sides experienced degenerative changes. No liver and kidney toxicity was observed in the two groups of animals. The 3D-printed mesh titanium alloy prostheses could effectively restore the shape of the mandibular defect region and reconstruct the temporomandibular joint.

OBJECTIVE: To evaluate the dimensional changes in free gingival grafts (FGG) at implant sites in mandibular reconstruction patients.
METHODS: Patients who received FGG 4 months after implant placement in the reconstructed mandible with no keratinized mucosa (KM) present were invited for re-examination after 36.7 ± 16.8 months (3.06 ± 1.4 years). Immediately after graft extraction (T0), graft width (GW), graft length (GL), graft thickness (GT), graft dimension (GD), and vertical bone height were documented. Re-examination (T1) included clinical examinations (GW, GL, GD, peri-implant probing depths, and modified Sulcus Bleeding Index), radiographic examination (marginal bone level), and medical chart review.
RESULTS: Twenty patients and 62 implants (47 in fibula flaps and 15 in iliac flaps) were included. A significant decrease in GW (51.8%), GL (19.2%), and GD (60.2%), were found between T0 and T1 (p < .001). The univariate analysis showed that GW change was not significantly associated with reconstruction technique, baseline GL, baseline GT, baseline GD, implant location, or type of prosthesis. Implant survival rate of 100% was observed at follow-up.
CONCLUSIONS: Within the limitations of the study, free gingival grafts at implant sites in the reconstructed mandible undergo dimensional change that result in a reduction of approximately 60% of the original graft dimension. Graft width decreased over 50%.
CONCLUSIONS: FGG is the standard of care intervention for increasing the amount of KM around implants. This study was the first to evaluate the dimensional change in FGG at implant sites in mandibular reconstruction patients after a medium-term follow-up.
BACKGROUND: Clinical trial registration is not applicable as this study comprehends a retrospective analysis.

Background: Virtual surgical planning has become a well-established practice in head and neck surgery. In oncological surgery, it permits the achievement of safe margins resections and ensures functional reconstructions and optimal esthetic outcomes. This study aimed to evaluate the long-term outcomes after virtually planned mandibular microvascular reconstruction, focusing on functional and esthetic results, as well as health-related quality of life. Methods: A long-term retrospective evaluation of 17 patients with oral cavity malignancy who underwent computer-assisted mandibular resection and reconstruction was performed. Functional and esthetic outcomes were analyzed using the EORTC, QLQ-C30, H&N35, and FACE-Q questionnaires. Results: Time since reconstruction ranged from 7 to 14 years. Patients reported high functional levels on the QLQ-C30 functional scales but lower scores on H&N35. On FACE-Q, patients demonstrated higher appraisal and satisfaction with their smiles compared to their overall facial appearance. Conclusions: In this retrospective case series, patients undergoing computer-assisted mandibular reconstruction for oral malignancies achieved good long-term functional and esthetic outcomes. Although limited by the small sample size, these results support the enduring benefits of virtual planning for mandibular reconstruction. To minimize declines in function and appearance, considerations should include immediate dental implants, enhanced reconstruction of the temporomandibular joint, newer methods of radiotherapy to minimize xerostomia, and oral exercises to prevent trismus.

Background/Objective: With the rapid advancement in surgical technologies, new workflows for mandibular reconstruction are constantly being evaluated. Cutting guides are extensively employed for defining osteotomy planes but are prone to errors during fabrication and positioning. A virtually defined osteotomy plane and drilling holes in robotic surgery minimize potential sources of error and yield highly accurate outcomes. Methods: Ten mandibular replicas were evaluated after cutting-guided saw osteotomy and robot-guided laser osteotomy following reconstruction with patient-specific implants. The descriptive data analysis summarizes the mean, standard deviation (SD), median, minimum, maximum, and root mean square (RMS) values of the surface comparison for 3D printed models regarding trueness and precision. Results: The saw group had a median trueness RMS value of 2.0 mm (SD ± 1.7) and a precision of 1.6 mm (SD ± 1.4). The laser group had a median trueness RMS value of 1.2 mm (SD ± 1.1) and an equal precision of 1.6 mm (SD ± 1.4). These results indicate that robot-guided laser osteotomies have a comparable accuracy to cutting-guided saw osteotomies, even though there was a lack of statistical significance. Conclusions: Despite the limited sample size, this digital high-tech procedure has been shown to be potentially equivalent to the conventional osteotomy method. Robotic surgery and laser osteotomy offers enormous advantages, as they enable the seamless integration of precise virtual preoperative planning and exact execution in the human body, eliminating the need for surgical guides in the future.

UNASSIGNED: Mandibular reconstruction with the free fibula flap (FFF) has become a standardized procedure. The situation is different with oral rehabilitation, so the purpose of this study was to investigate the frequency of implant placement and prosthetic restoration. Additionally, the patients\' situation, motivation, and treatment course were structurally assessed.
UNASSIGNED: All cases between January 2013 and December 2018 that underwent mandibular reconstruction in our department with a free fibula flap and gave written informed consent to participate were interviewed with two structured questionnaires about their restoration and quality of life. Additionally, medical records, general information, status of implants and therapy, and metric analyses of the inserted implants were performed.
UNASSIGNED: In total 59 patients were enrolled and analyzed in this monocentric study. Overall, oral rehabilitation was achieved in 23.7% at the time of investigation. In detail, implants were inserted in 37.3% of patients and showed an 83.3% survival of dental implants. Of these implanted patients, dental implants were successfully restored with a prosthetic restoration in 63.6. Within this subgroup, satisfaction with the postoperative aesthetic and functional result was 79.9% and with the oral rehabilitation process was 68.2%. Satisfaction with the implant-borne prosthesis was 87.5%, with non-oral-squamous-cell-carcinoma patients being statistically significantly more content with the handling (p=0.046) and care (p=0.031) of the prosthesis.
UNASSIGNED: Despite the well-reconstructed bony structures, there is a need to increase the effort of achieving oral rehabilitation, especially looking at the patient\'s persistent motivation for the procedure.

OBJECTIVE: Microvascular bone flap jaw reconstruction has achieved satisfactory clinical outcomes. However, little is known about the long-term stability of the reconstructed jaw. This prospective longitudinal study aimed to investigate the long-term stability of jaw reconstruction and factors that were associated with it.
METHODS: Patients with successful computer-assisted osseous free-flap jaw reconstruction in the Department of Oral and Maxillofacial Surgery, Queen Mary Hospital, Hong Kong were recruited for this prospective longitudinal study. The three-dimensional jaw models at the pre-operative plan, post-operative 1-month, and 2 years were aligned and compared.
RESULTS: A total of 69 patients were recruited, among which 48 patients were available for the long-term analysis. Compared to 1-month after surgery, further deviation from the pre-operative plan was observed at post-operative 2 years. Lack of accuracy in surgery, segmental mandible resection especially with the involvement of mandible angles, and post-operative radiation therapy were identified as the significant factors affecting the positional stability of the reconstructed jaw (p < 0.05). Stable reconstruction was observed in the subgroup analysis of patients without post-operative radiation therapy.
CONCLUSIONS: Up to the best of our knowledge, this is the first prospective longitudinal study reporting the long-term stability of jaw reconstruction and its affecting factors. Our data demonstrated that the reconstructed jaw position lacked stability over the postoperative period. How to improve long-term stability of reconstructed jaw thus optimize the functional outcomes warrants further studies.

Liposarcomas are described as soft tissue sarcomas derived from adipose tissue. The finding of this tumor in the mandibular region is exceedingly rare. As of now, it has been described mainly in case reports and small series. A multidisciplinary approach is required to offer optimal treatment and may involve surgery, radiation and systemic therapies. Surgical repair of these defects represents a major challenge in oral and maxillofacial reconstructive surgery. We present the case of a 54-year-old man referred to our center with a progressively increasing mass in the anterior portion of the mandible. Biopsy revealed a well-differentiated myxoid liposarcoma. Resection of the tumor was performed with an additional primary reconstruction.

This study aimed to compare the functional and esthetic results in patients following mandibular reconstruction with a free fibula flap (FFF) by virtual surgical planning (VSP) versus the conventional technique. Patients who had undergone mandibular reconstruction with a FFF by VSP or the conventional technique were retrospectively assessed. The two groups were compared regarding functional and esthetic variables with appropriate scales preoperatively, intraoperatively, and postoperatively. Twenty-four patients were evaluated in two groups: conventional (n = 8) and VSP (n = 16). The mean amount of mandibular asymmetry was 2.62 mm (SD = 1.59) in the conventional group and 1.19 mm (SD = 1.32) in the VSP group. Of the patients who underwent conventional surgery, 12.5% had mandibular asymmetry of <2 mm and 87.5% had asymmetry of 2-5 mm. Of the VSP patients, 61.5% had mandibular asymmetry of <2 mm and 38.5% had mandibular asymmetry of 2-5 mm (p = 0.03). The mean difference in size of mandibular angle on the surgical and control sides was not significantly different between the two groups (p = 0.62). The difference in mean length of the mandibular body on the surgical side relative to the control side was not significant between the two groups (p = 0.75). Differences in functional variables between the two groups were not significant. Within the limitation of the study, it seems that the VSP technique resulted in better facial symmetry and superior esthetic outcomes compared with the conventional technique.

BACKGROUND: Reconstruction of mandibular defects caused by combat injuries is challenging for clinicians due to soft tissue defects and high complication risk. This study evaluated the outcomes of mandibular continuous defects reconstruction with non-vascularized iliac crest graft (NVICG) in patients with combat injuries.
METHODS: Patients with continuous mandibular defects acquired by high-velocity agents, who received NVICG reconstruction with or without microvascular-free soft tissue or regional flaps, were included in the study. The outcome variable was graft loss due to postoperative complications or full (more than 90 %) resorption. The primary predictor variable was soft tissue defect in the recipient area. The secondary predictor variable was the length of the defect. Variables related to patients, defect site, surgery, and other complications were also evaluated. Statistical analysis was performed with the usage of independent sample t-test, Pearson\'s chi-squared and Fisher\'s exact tests with a significance level of P < 0.05 RESULTS: The study included 24 patients with 27 mandibular defects. Overall, the general success rate of reconstructions was 59.3 %. Soft tissue defects were significantly associated with graft failure and other complications (p < 0.05), which were mostly related to soft tissue defects. The graft success rate was only 14.3 % even in minor soft tissue defects. In turn, in reconstructions with sufficient soft tissue coverage, the graft survived in 75.0 % of the cases. In addition, patients with more delayed reconstruction had significantly fewer graft failures than those with earlier surgery (p < 0.05). No associations were found between defect size and complications.
CONCLUSIONS: The sufficient soft tissue coverage is essential in the reconstruction of mandibular defects caused by combat injuries. Also, minor soft tissue defects should be covered with soft tissue flaps to avoid complications and graft loss in these specific injuries. Even large defects can be reconstructed with NIVICG if the soft tissue coverage is sufficient.

Segmental bone defects of the mandible result in the complete loss of the affected region. We had incorporated the pressure-reducing device (PRD) designs into the customized mandible prostheses (CMP) and conducted a clinical trial to evaluate this approach.
Seven patients were enrolled in this study. We examined the association among the history of radiotherapy, the number of CMP regions, the number of chin regions involved, and CMP exposure.
We included five men and two women with an average age of 55 years. We excised tumors with an average weight of 147.8 g and the average weight of the CMP was 68.5 g. No significant difference between the two weights was noted (p = 0.3882). Three patients received temporary dentures and the CMP remained stable in all patients.
The use of PRD in CMP may address the previous challenges associated with CMP, but further research is necessary.