This study introduces draw solutions for application in forward osmosis (FO) processes, combining mono propylene glycol propyl ether (PGPE) with the cellulose derivative hydroxypropyl cellulose (HPC). A total of 16 unique single-solute and ternary organic draw solutions were prepared and evaluated, leading to the selection of three promising solutions for further investigation. Notably, eight of the initial organic draw solutions demonstrated osmotic pressures exceeding 2.4 MPa. The dynamic viscosities of all draw solutions exhibited a significant reduction with increasing temperature. Among the investigated solutions, the 0.25HPC-3.75PGPE demonstrated the most favorable FO performance, achieving average experimental water fluxes of 11.062 and 9.852 Lm-2 h-1 (LMH) against a 1 g/L NaCl brackish feed solution across two FO runs. PRACTITIONER POINTS: Hydroxypropyl cellulose (HPC, MW ~100,000) was mixed with propylene glycol propyl ether (PGPE) as draw solutes for FO processes. Seven combinations of HPC and PGPE produced osmolalities greater than 1000 mOsm/kg. 0.5HPC-7.5PGPE ternary draw solution achieved experimental water fluxes of 11.062 and 9.852 LMH against 1 g/L NaCl brackish feed solution. Leveraging the LCSTs of these ternary organic solutions holds promise for improved separation and regeneration processes.

UNASSIGNED: The two-component signal transduction systems play an essential role in the adaptation of bacteria to changing environmental conditions. One of them is the MnoSR system involved in the regulation of methylotrophic metabolism in M. smegmatis.
UNASSIGNED: Mycobacterium smegmatis mutant strains ΔmnoS, ΔmnoR and ΔmnoS/R lacking functional mnoS, mnoR and both genes were generated using a homologous recombination approach. MnoR recombinant protein was purified by affinity column chromatography. The present study employs molecular biology techniques: cloning strategies, global RNA sequencing, qRT-PCR, EMSA, Microscale thermophoresis, and bioinformatics analysis.
UNASSIGNED: The ∆mnoS, ∆mnoR, and ∆mnoS/R mutant strains were generated and cultured in the presence of defined carbon sources. Growth curve analysis confirmed that inactivation of the MnoSR impairs the ability of M. smegmatis cells to use alcohols such as 1,3-propanediol and ethanol but improves the bacterial growth on ethylene glycol, xylitol, and glycerol. The total RNA sequencing method was employed to understand the importance of MnoSR in the global responses of mycobacteria to limited carbon access and in carbon-rich conditions. The loss of MnoSR significantly affected carbon utilization in the case of mycobacteria cultured on glucose or 1,3-propanediol as sole carbon sources as it influenced the expression of multiple metabolic pathways. The numerous transcriptional changes could not be linked to the presence of evident MnoR DNA-binding sites within the promotor regions for the genes outside of the mno operon. This was confirmed by EMSA and microscale thermophoresis with mutated MnoR binding consensus region. Our comprehensive analysis highlights the system\'s vital role in metabolic adaptability, providing insights into its potential impact on the environmental survival of mycobacteria.

Hierarchically porous monoliths with satisfactory properties have been employed in diverse fields, especially separation. In this study, pentafluorophenyl acrylate (PFPA), pentaerythritol tetraacrylate (PETA) and trimethylolpropane tris(3-mercaptopropionate) (TTMP) were selected as precursors to fabricate a novel monolithic column by thermally initiated polymerization in the presence of a binary porogenic system containing tetrahydrofuran and 1-propanol. The fabricated poly(PFPA-co-PETA-co-TTMP) monolithic column revealed excellent permeability and mechanical stability. Additionally, baseline separation of the mixture of small molecules can be achieved, involving alkylbenzene and fluorobenzene in chromatographic assessment, and the theoretical plate number is up to 60,500 plates/m for butylbenzene with a linear velocity of 0.14 mm/s. Tryptic digest of HeLa as an analyte was used to investigate the possibility of the poly(PFPA-co-PETA-co-TTMP) monolith in biological separation by cLC-MS/MS. Moreover, benefiting from the existence of pentafluorophenyl groups, the cucurbit[8]uril (CB[8]) could be modified on the prepared poly(PFPA-co-PETA-co-TTMP) monolith through host-guest interaction to obtain poly(PFPA-co-PETA-co-TTMP)-CB[8] monolith. It could be observed that significant changes in retention behavior of analytes appeared after immobilizing CB[8] on the monolith. It offered an innovative approach by utilizing host-guest interaction to fabricate monolithic columns with different chromatographic behaviors.

BACKGROUND: (R,R)-2,3-butanediol (BDO) is employed in a variety of applications and is gaining prominence due to its unique physicochemical features. The use of glycerol as a carbon source for 2,3-BDO production in Klebsiella pneumoniae has been limited, since 1,3-propanediol (PDO) is generated during glycerol fermentation.
RESULTS: In this study, the inactivation of the budC gene in K. pneumoniae increased the production rate of (R,R)-2,3-BDO from 21.92 ± 2.10 to 92.05 ± 1.20%. The major isomer form of K. pneumoniae (meso-2,3-BDO) was shifted to (R,R)-2,3-BDO. The purity of (R,R)-2,3-BDO was examined by agitation speed, and 98.54% of (R,R)-2,3-BDO was obtained at 500 rpm. However, as the cultivation period got longer, the purity of (R,R)-2,3-BDO declined. For this problem, a two-step agitation speed control strategy (adjusted from 500 to 400 rpm after 24 h) and over-expression of the dhaD gene involved in (R,R)-2,3-BDO biosynthesis were used. Nevertheless, the purity of (R,R)-2,3-BDO still gradually decreased over time. Finally, when pure glycerol was replaced with crude glycerol, the titer of 89.47 g/L of (R,R)-2,3-BDO (1.69 g/L of meso-2,3-BDO), productivity of 1.24 g/L/h, and yield of 0.35 g/g consumed crude glycerol was achieved while maintaining a purity of 98% or higher.
CONCLUSIONS: This study is meaningful in that it demonstrated the highest production and productivity among studies in that produced (R,R)-2,3-BDO with a high purity in Klebsiella sp. strains. In addition, to the best of our knowledge, this is the first study to produce (R,R)-2,3-BDO using glycerol as the sole carbon source.

Bioengineering seeks to replicate biological tissues exploiting scaffolds often based on polymeric biomaterials. Digital light processing (DLP) has emerged as a potent technique to fabricate tissue engineering (TE) scaffolds. However, the scarcity of suitable biomaterials with desired physico-chemical properties along with processing capabilities limits DLP\'s potential. Herein, we introduce acrylate-endcapped urethane-based polymers (AUPs) for precise physico-chemical tuning while ensuring optimal computer-aided design/computer-aided manufacturing (CAD/CAM) mimicry. Varying the polymer backbone (i.e. poly(ethylene glycol) (PEG) versus poly(propylene glycol) (PPG)) and photo-crosslinkable endcap (i.e. di-acrylate versus hexa-acrylate), we synthesized a series of photo-crosslinkable materials labeled as UPEG2, UPEG6, UPPG2 and UPPG6. Comprehensive material characterization including physico-chemical and biological evaluations, was followed by a DLP processing parametric study for each material. The impact of the number of acrylate groups per polymer (2 to 6) on the physico-chemical properties was pronounced, as reflected by a reduced swelling, lower water contact angles, accelerated crosslinking kinetics, and increased Young\'s moduli upon increasing the acrylate content. Furthermore, the different polymer backbones also exerted a substantial effect on the properties, including the absence of crystallinity, remarkably reduced swelling behaviors, a slight reduction in Young\'s modulus, and slower crosslinking kinetics for UPPG vs UPEG. The mechanical characteristics of DLP-printed samples showcased the ability to tailor the materials\' stiffness (ranging from 0.4 to 5.3 MPa) by varying endcap chemistry and/or backbone. The in vitro cell assays confirmed biocompatibility of the material as such and the DLP-printed discs. Furthermore, the structural integrity of 3D scaffolds was preserved both in dry and swollen state. By adjusting the backbone chemistry or acrylate content, the post-swelling dimensions could be customized towards the targeted application. This study showcases the potential of these materials offering tailorable properties to serve many biomedical applications such as cartilage TE.

This study investigates the nanoscale self-assembly from mixtures of two symmetrical poly(ethylene oxide)-poly(propylene oxide)-pol(ethylene oxide) (PEO-PPO-PEO) block copolymers (BCPs) with different lengths of PEO blocks and similar PPO blocks. The blended BCPs (commercially known as Pluronic F88 and L81, with 80 and 10% PEO, respectively) exhibited rich phase behavior in an aqueous solution. The relative viscosity (ηrel) indicated significant variations in the flow behavior, ranging from fluidic to viscous, thereby suggesting a possible micellar growth or morphological transition. The tensiometric experiments provided insight into the intermolecular hydrophobic interactions at the liquid-air interface favoring the surface activity of mixed-system micellization. Dynamic light scattering (DLS) and small-angle neutron scattering (SANS) revealed the varied structural morphologies of these core-shell mixed micelles and polymersomes formed under different conditions. At a concentration of ≤5% w/v, Pluronic F88 exists as molecularly dissolved unimers or Gaussian chains. However, the addition of the very hydrophobic Pluronic L81, even at a much lower (<0.2%) concentration, induced micellization and promoted micellar growth/transition. These results were further substantiated through molecular dynamics (MD) simulations, employing a readily transferable coarse-grained (CG) molecular model grounded in the MARTINI force field with density and solvent-accessible surface area (SASA) profiles. These findings proved that F88 underwent micellar growth/transition in the presence of L81. Furthermore, the potential use of these Pluronic mixed micelles as nanocarriers for the anticancer drug quercetin (QCT) was explored. The spectral analysis provided insight into the enhanced solubility of QCT through the assessment of the standard free energy of solubilization (ΔG°), drug-loading efficiency (DL%), encapsulation efficiency (EE%), and partition coefficient (P). A detailed optimization of the drug release kinetics was presented by employing various kinetic models. The [3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide] MTT assay, a frequently used technique for assessing cytotoxicity in anticancer research, was used to gauge the effectiveness of these QCT-loaded mixed nanoaggregates.

Toehold-mediated strand displacement (TMSD) reaction, one of the DNA nanotechnologies, has great potential as s biological programmable platform in the cellular environment. Various artificial nucleic acids have been developed to improve stability and affinity for biological applications. However, the lack of understanding of the kinetics of TMSD reaction among artificial nucleic acids has limited their applications. We herein systematically characterized the kinetics of TMSD reactions with acyclic xeno nucleic acids (XNAs): serinol nucleic acid (SNA), acyclic D-threoninol nucleic acid (D-aTNA), and acyclic L-threoninol nucleic acid (L-aTNA). We found that the strand displacement reactions by D-aTNA and by L-aTNA were highly dependent on temperature. D-aTNA and L-aTNA systems were orthogonal to each other, and chirality of the input can be switched by using SNA as an interface. We also applied TMSD reactions of XNAs to a seesaw gate amplification system which utilizes the orthogonality. This work will contribute to the developments of thermoresponsive and bioorthogonal nucleic acid circuits.

A reactor with silicone tubes as support medium was used for glycerol fermentation. The experimental set-up consisted of three phases. In P1, the applied glycerol loading rate (gly-LR) was in the range of 6-10 g.L-1.d-1 at an influent pH of 7.9 ± 0.4. In P2, gly-LR was kept constant (18.0 ± 1.8 g.L-1.d-1) with different doses of NaHCO3. Finally in P3, two different gly-LR (9 and 18 g.L-1.d-1) were evaluated, dosing 1 g-NaHCO3 per g-COD of glycerol. Glycerol consumption was close 90%. The main end-product was 1,3-propanediol (1,3-PDO) (0.40 mol.mol-gly-1), but ethanol was also generated, particularly at pH above 8 and low gly-LR (0.20 mol.mol-gly-1). After 1-year operation with glycerol as the only carbon source, a drastic shift in the bacterial community was observed. The 1,3-PDO producers Lacrimispora and Clostridium became dominant, although non-glycerol-degrading fermentative genera, e.g., Actinomyces and Eubacterium, thrived at the expense of cellular breakdown products.

Advancements in synthetic biology have facilitated the incorporation of heterologous metabolic pathways into various bacterial chassis, leading to the synthesis of targeted bioproducts. However, total output from heterologous production pathways can suffer from low flux, enzyme promiscuity, formation of toxic intermediates, or intermediate loss to competing reactions, which ultimately hinder their full potential. The self-assembling, easy-to-modify, protein-based bacterial microcompartments (BMCs) offer a sophisticated way to overcome these obstacles by acting as an autonomous catalytic module decoupled from the cell\'s regulatory and metabolic networks. More than a decade of fundamental research on various types of BMCs, particularly structural studies of shells and their self-assembly, the recruitment of enzymes to BMC shell scaffolds, and the involvement of ancillary proteins such as transporters, regulators, and activating enzymes in the integration of BMCs into the cell\'s metabolism, has significantly moved the field forward. These advances have enabled bioengineers to design synthetic multi-enzyme BMCs to promote ethanol or hydrogen production, increase cellular polyphosphate levels, and convert glycerol to propanediol or formate to pyruvate. These pioneering efforts demonstrate the enormous potential of synthetic BMCs to encapsulate non-native multi-enzyme biochemical pathways for the synthesis of high-value products.

This study investigated the effect of cooking on the levels of 3-chloro-1, 2-propanediol esters (3-MCPDEs), 2-chloro-1, 3-propanediol esters (2-MCPDEs) and glycidyl esters (GEs) in deep-fried rice cracker, fried potato, croquette, fish fillet, chicken fillet and cooking oils (rice bran oil and palm oil). The levels of 2-/3-MCPDE in rice cracker fried with rice bran oil and the used oil remained about the same, while the levels of GEs in them fell with frying time. The levels of 2-/3-MCPDEs in fried potato, croquette, fried fish and chicken cutlet fried with rice bran oil and palm oil respectively fell with frying time, while the level of GEs in them remained about the same. The levels of 2-/3-MCPDEs and GEs in fried rice cooked with rice bran oil were under the method limit of quantification. These results provide insights the cooking has no influence with the levels of 2-/3-MCPDEs and GEs in cooked foods.