Stainless steel welders are exposed to heavy filler metals. We evaluated the concentration of these metals in whole blood and urine, and the relevant biochemical parameters in relation to the total chromosomal aberrations (CAs), chromatid-type (CTA-type, CTAs) and chromosome-type (CSA-type, CSAs), in 117 welders and control individuals. Statistically higher concentrations of the total Cr, Ni and Mn were observed in whole blood and urine of welders, and the concentrations were higher in welders who smoked. On the contrary, concentrations of urinary heavy metals Cr and Mn adjusted for creatinine were significantly higher in the control groups. A statistically higher frequency of total CAs was observed in the whole group of welders, and also in the non-smoking welders, as compared to controls. The frequency of total CAs significantly correlated with the concentration of Cr, Ni and Mn in whole blood (R=0.61, P˂0.0001, R=0.33, P˂0.0001 and R=0.66, P˂0.0001, respectively), with urinary concentrations of Ni and Mn (R=0.27, P=0.003 and R=0.28, P=0.003, respectively) and with urinary concentrations of Cr, Ni and Mn adjusted for creatinine (R=0.22, P=0.029, R=0.26, P=0.005 and R=0.20, P=0.030, respectively). Likewise, the frequency of CTA-types significantly correlated with the concentration of Cr and Mn in whole blood (R=0.31, P=0.0007 and R=0.34, P=0.0002). The frequency of CSA-types significantly correlated with concentrations of Cr, Ni and Mn in whole blood (R=0.43, P˂0.0001, R=0.38, P˂0.0001 and R=0.46, P˂0.0001, respectively). The statistically higher values of serum creatinine and total bilirubin were detected in all welders, as well as in smokers when compared to the corresponding controls. The exposure to heavy metals in welders increased the frequencies of CAs and altered the balance between urinary excretion of heavy metals and their possible accumulation.

The impact of multiple reuse on the alterations in internal threads of four different implant analogous composed of different materials (stainless steel (SS), aluminum (Al), titanium (Ti), and zirconia (Zr) by utilizing two die materials at different time durations is of interest to dentists. The spacing between the threads was measured using the impressions created for the interior threads of implant analogs, or replicas by stereomicroscope set to x50 at 0th, 3rd, 6th, 9th, and 12th interval. It was observed that there was decrease in distance between threads 1-2 as the increasing reuse at increasing time intervals in all implants analogs. However the decrease in distance between threads was low in Titanium implants analogs followed by Zircona implant analogs and the decrease was maximum in aluminum implants analogs followed by SS implant analogs. When there was evaluation of distance between threads 3-4 then it was observed that there was reduced decrease in distance between threads 3-4 as compared to threads 1-2 n all implant analogs. Similarly the reduction in distance between threads 5-6 was lesser as compared to threads 1-2 and threads 3-4. There was decrease in distance between threads 1-2 as the increasing reuse at increasing time intervals in all implants analogs. However, the reduction in distance between threads was lowest in Titanium implants analogs followed by Zircona implant analogs.

Rehabilitation of pulpotomized primary molars with an appropriate restoration is essential for recovering function and safeguarding the durability of the treatment. This study aimed to assess and compare the surface roughness of stainless steel (ST) crowns, zirconia (ZR) crowns, fiberglass (FG) crowns, and lithium disilicate (LD) endo-crowns as a restoration for pulpotomized primary molars also, evaluating the surface roughness of their antagonists. Sixty pulpotomized primary mandibular first molars were used for qualitative surface roughness evaluation and divided into four groups (n = 15/group) according to the crown type (group-ST, group-ZR, group-FG, group-LD). While the other sixty sound, unprepared primary maxillary first molars were used for evaluation of their surface roughness against the tested crowns. Specimens\' preparation and cementation were carried out according to each crown type and manufacturer\'s instructions. The surface roughness was done using a two-body wear test. The data were statistically analyzed. All tested crowns showed an increased change in surface roughness, except group-ZR, which had the least change in surface roughness after mechanical wear with no statistically significant difference(P = 0.681). All crown types significantly increased the surface roughness of their antagonists after mechanical wear, except group-ST which showed insignificant affection (p ≥ 0.05). Zirconia crowns and lithium disilicate endo-crowns had the least change in surface roughness compared to other groups while SSCs showed the least tooth loss in the antagonist enamel.

In order to facilitate the application of underwater laser welding technology in in situ repairs of nuclear power plants, this study conducted comparative experiments between local dry underwater laser welding and laser welding in air on 304NG nitrogen-controlled stainless steel. The aim was to explore its microstructural evolution and mechanical properties in underwater environments. It was found that, near the fusion line of laser welding in air, columnar dendrites gradually evolved into cellular dendrites toward the weld center, eventually disappearing, resulting in a skeletal ferrite and serrated austenite structure. The underwater laser welding joints exhibited similar characteristics yet with more pronounced alternation between columnar and cellular dendrites. Additionally, the size of cellular dendrites decreased significantly, and needle-like ferrite was observed at the weld center. The hardness of underwater laser welded joints was slightly higher than that of in-air laser welded joints. Compared to laser welding in air, the strength of underwater laser welding joints increased from 443 MPa to 471 MPa, and the displacement increased from 2.95 mm to 3.45 mm, both types of welded joints exhibited a mixed mode fracture characterized by plasticity and brittleness.

In this study, we optimized the parameters of diffusion bonding on multi-layered stainless steel 316L and 430 stacks. The preparation process for diffusion bonding is crucial, as the bonding surfaces need to be polished and meticulously cleaned to ensure a smooth bonding process. We fabricated twelve-layer plates consisting of 55 mm × 55 mm × 3 mm and 100 mm × 50 mm × 3 mm dimensions, and the bonding response was investigated by evaluating the tensile strength of the bonding zone under varying bonding conditions, with a bonding temperature ranging from 1000 to 1048 °C, a bond time ranging from 15 to 60 min, pressure ranging from 10 to 25.3 MPa, and under a vacuum environment. SS430 exhibits a significantly higher compression creep rate than SS316L. The compressibility of diffusion welding materials does not impact the diffusion bonding strength. Multi-axial tensile strength tests confirmed strong bonding joint strength in various axes. The tensile strengths of monolithic and Diffusion bonding (DB) specimens tested in parallel are essentially identical. The optimized diffusion bonding parameters (Condition G2C: 1048 °C/25.3 MPa/15 min) are ideal for producing SS316L stainless steel cores in compact heat exchangers, offering a superior bonding quality and reduced costs. These findings have practical implications for the production of stainless steel cores in compact heat exchangers, demonstrating the relevance and applicability of our research.

OBJECTIVE: To identify the characteristics of patients and femur fractures treated with a stainless steel intramedullary nail (ESIN) in children under 15 years of age. Know the results of using the ESIN of related steel in the service.
METHODS: Retrospective study with review of hospital records and organization of data in spreadsheets.
RESULTS: 24 cases were identified, 17 male cases and 7 female cases. A minimum age of 4 years and a maximum of 11 years were observed (average of 7 years). The 3 most common trauma mechanisms were being run over (n:8, 33%) and falling from a height (n:8, 3%). The most common location of the fractures was in the mid-diaphyseal region (n: 20, 88%), only one case presented a bilateral femur fracture. The most common associated trauma was traumatic brain injury. The observation period observed several months between 2 and 5. With regard to complications, 3 cases were observed (12.5%) being bursitis, vicious construction and loss of reduction.
CONCLUSIONS: Steel HIF shows similar good results. As the study includes the retrospective profile, the absence of a group and the small sample size. Level of Evidence IV, Case series.
OBJECTIVE: Identificar as características dos pacientes e das fraturas de fêmur tratadas com haste intramedular flexível (HIF) de aço inoxidável em menores de 15 anos. A partir disso, conhecer os resultados relacionados ao uso da HIF de aço inoxidável no serviço. Métodos: Estudo retrospectivo, com revisão de prontuários hospitalares e organização dos dados em planilhas.
RESULTS: Identificados 24 casos, sendo 17 do gênero masculino e sete do gênero feminino. Foram observadas idade mínima de 4 anos e máxima de 11 anos (média de 7 anos). Os mecanismos de trauma mais comuns foram atropelamento (n: 8, 33%) e queda de altura (n: 8, 33%). A localização mais comum das fraturas foi na região médio diafisária (n: 20, 88%), apenas um caso apresentou fratura de fêmur bilateral. O trauma associado mais comum foi traumatismo crânio-encefálico. O período de consolidação observado variou entre 2 e 5 meses. No que se refere a complicações, foram observados três casos (12,5%), sendo estes: bursite, consolidação viciosa e perda de redução. Conclusão: A HIF de aço apresenta bons resultados, semelhantes aos das hastes de titânio. As limitações do estudo incluem o perfil retrospectivo, a ausência de grupo controle e o número pequeno da amostra. Nível de evidência IV, Série de casos.

Radiotherapy (RT) is one of the most widely used and effective cancer treatments. With the increasing need for organ reconstruction and advancements in material technology, an increasing number of patients with cancer have metallic implants. These implants can affect RT dosage and clinical outcomes, warranting careful consideration by oncologists. The present review discussed the mechanisms by which different types of metallic implants impact various stages of the RT process, examined methods to mitigate these effects during treatment, and discussed the clinical implications of metallic implants on RT outcomes. In summary, when metallic implants are present within the RT field, oncologists should carefully assess their impact on the treatment.

The ever-increasing use of exogenous materials as indwelling medical devices in modern medicine offers to pathogens new ways to gain access to human body and begin, in some cases, life threatening infections. Biofouling of such materials with bacteria or fungi is a major concern during surgeries, since this is often associated with biofilm formation and difficult to treat, recalcitrant infections. Intense research efforts have therefore developed several strategies to shield the medical devices\' surface from colonization by pathogenic microorganisms. Here, we used dopamine as a coupling agent to coat four different materials of medical interest (plastic polyetheretherketone (PEEK), stainless steel, titanium and silicone catheter) with the bacteriocins, enterocin EJ97-short and the thiopeptide micrococcin P1. Water contact angle measurements and x-ray photoelectron spectroscopy were used to verify the effective coating of the materials. The effect of bacteriocins coated on these materials on the biofilm formation by a vancomycin resistant Enterococcus faecium (VRE) strain was studied by biofilm-oriented antimicrobial test (BOAT) and electron scanning microscopy. The in vitro biocompatibility of bacteriocin-modified biomaterials was tested on cultured human cells. The results demonstrated that the binding of the bacteriocins to the implant surfaces is achieved, and the two bacteriocins in combination could inhibit biofilm formation by E. faecium on all four materials. The modified implant showed no cytotoxicity to the human cells tested. Therefore, surface modification with the two bacteriocins may offer a novel and effective way to prevent biofilm formation on a wide range of implant materials.

Copper-containing materials are attracting attention as self-disinfecting surfaces, suitable for helping healthcare settings in reducing healthcare-associated infections. However, the impact of repeated exposure to disinfectants frequently used in biocleaning protocols on their antibacterial activity remains insufficiently characterized. This study aimed at evaluating the antibacterial efficiency of copper (positive control), a brass alloy (AB+®) and stainless steel (negative control) after repeated exposure to a quaternary ammonium compound and/or a mix of peracetic acid/hydrogen peroxide routinely used in healthcare settings. A panel of six antibiotic-resistant strains (clinical isolates) was selected for this assessment. After a short (5 min) exposure time, the copper and brass materials retained significantly better antibacterial efficiencies than stainless steel, regardless of the bacterial strain or disinfectant treatment considered. Moreover, post treatment with both disinfectant products, copper-containing materials still reached similar levels of antibacterial efficiency to those obtained before treatment. Antibiotic resistance mechanisms such as efflux pump overexpression did not impair the antibacterial efficiency of copper-containing materials, nor did the presence of one or several genes related to copper homeostasis/resistance. In light of these results, surfaces made out of copper and brass remain interesting tools in the fight against the dissemination of antibiotic-resistant strains that might cause healthcare-associated infections.

The oxidation behaviour of iron-based 316L stainless steel was investigated in the temperature range of 700 to 1000 °C. The test specimens in the shape of plates were produced by selective laser melting. After fabrication, the samples were sandblasted and then annealed in air for different periods of time (0.5, 2, 8, 32 h). Under the influence of temperature and time, stainless steels tend to form an oxide layer. Scanning electron microscopy, energy dispersive analysis, and X-ray diffraction were employed to analyse the composition of this layer. Notably, a thin oxide layer primarily composed of (Fe-Cr) formed on the surface due to temperature effects. In addition, with increasing temperature (up to 1000 °C), the oxide of the main alloying elements, specifically Mn2(Fe-Cr)O4, appeared alongside the Fe-Cr oxide. Furthermore, the samples were subjected to conversion X-ray (CXMS) and conversion electron (CEMS) Mössbauer spectroscopy. CXMS revealed a singlet with a decreasing Mössbauer effect based on the surface metal oxide thickness. CEMS revealed the presence of Fe3+ in the surface layer (0.3 µm). Moreover, an interesting phenomenon occurred at higher temperature levels due to the inhomogeneously thick surface metal oxide layer and the tangential direction of the Mössbauer radiation towards the electron detector.