Polymer flooding is an effective development technology to enhance oil recovery, and it has been widely used all over the world. However, after long-term polymer flooding, a large number of oilfields have experienced a sharp decline in reservoir development efficiency. High water cut wells, serious dispersion of residual oil distribution and complex reservoir conditions all bring great challenges to enhance oil recovery. In this study, the method of enhancing oil recovery after polymer flooding was studied by taking the S Oilfield as an example. A surfactant-polymer system suitable for high-permeability heterogeneous oilfields was developed, comprising biogenic surfactants and polymers. Microscopic displacement experiments were conducted using cast thin sections from the S Oilfield, and nuclear magnetic resonance was employed for core displacement experiments. Numerical simulation experiments were also conducted on the S Oilfield. The results show that the enhanced oil recovery mechanism of the surfactant-polymer system is to adjust the flow direction, expand the swept volume, emulsify crude oil and reduce interfacial tension. Surfactant-polymer flooding proves to be effective in improving recovery efficiency, significantly reducing the time of flooding and further enhancing the strong swept area. The nuclear magnetic resonance results indicate a high amplitude of passive utilization of residual oil during the surfactant-polymer flooding stage, highlighting the enormous potential for an increased recovery ratio. Surfactant-polymer flooding emerges as a more suitable technique to enhance oil recovery in the post polymer-flooding stage in high-permeability heterogeneous oilfields.

After polymer flooding, the heterogeneity between different layers intensifies, forming intricate seepage channels and fluid diversions, which results in decreased circulation efficiency and lower recovery rates, leaving a significant amount of residual oil trapped within the reservoir. Understanding the characteristics of residual oil occurrence is crucial for enhancing oil recovery post-polymer flooding. This study focused on sandstone reservoirs with varying permeability in the Saertu block of the Daqing oilfield. Using cryosectioning and laser scanning confocal microscopy, the occurrence characteristics of the residual oil in these sandstone reservoirs post-polymer flooding were investigated. Additionally, micro-CT and scanning electron microscopy were employed to analyze the impact of the pore structure on the distribution characteristics of the residual oil. The results indicate that laser scanning confocal images reveal that post-polymer flooding, the residual oil in high- and low-permeability sandstone reservoirs predominantly exists in a bound state (average > 47%), mostly as particle-adsorbed oil. In contrast, the residual oil in medium-permeability reservoirs is primarily in a free state (average > 49%), mostly as intergranular-adsorbed oil. In high-permeability sandstone reservoirs, heavy oil components are mainly in a particle-adsorbed form; in medium-permeability sandstone reservoirs, residual oil predominantly consists of heavy components, with most light components occurring in a clustered form; in low-permeability sandstone reservoirs, clustered residual oil exists in a balanced coexistence of light and heavy components, while the heavy components primarily exist in a particle-adsorbed form. Post-polymer flooding, the large pore-throat structure in high-permeability sandstone reservoirs results in effective displacement and less free residual oil; medium-permeability sandstone reservoirs, with medium-large pores and throats, have preferential channels and fine particles blocking the throats, leading to some unswept pores and more free residual oil; low-permeability sandstone reservoirs, with small pores and throats, exhibit weak displacement forces and poor mobility, resulting in more bound residual oil. The distribution and content of clay particles and clay minerals, along with the complex microscopic pore structure, are the main factors causing the differences in the residual oil occurrence states in sandstones with varying permeability.

In order to effectively adjust reservoir heterogeneity and further exploit the remaining oil, a new type of low-viscosity gel was prepared by adding a regulating agent, retarder, and reinforcing agent on the basis of a polymer + Cr3+ crosslinking system. The new gel has the advantages of low initial viscosity, a slow gel formation rate, and high strength after gel formation. The effectiveness of the gel was verified through three-layer core displacement experiments, and the injection scheme was optimized by changing the slug combination of the polymer and the gel. The results showed that the gel can effectively block the high-permeability layer and adjust reservoir heterogeneity. An injection of 0.1 pore volume (PV) low-initial-viscosity gel can improve oil recovery by 5.10%. By changing the slug combination of the gel and polymer, oil recovery was further increased by 3.12% when using an injection of 0.07 PV low-initial-viscosity gel +0.2 PV high-concentration polymer +0.05 PV low-initial-viscosity gel +0.5 PV high-concentration polymer.

Polymer flooding, one of the main methods for improving crude oil recovery using chemical flooding technology in China, is widely used for actual oil displacement. Partially hydrolyzed polyacrylamide (HPAM) is a commonly used linear polymer in polymer flooding, but it exhibits poor temperature and salt resistance due to its molecular structure. Therefore, branched polymers have been studied. This article provides a review of the specific synthetic methods and current practical applications in the petrochemical field of dendritic polymers and hyperbranched macromolecules. The advantages and disadvantages of each synthetic method for branched polymers are also elaborated. Finally, the application prospects of branched polymers are discussed. The feasibility of branched polymers in large quantities should be further verified through additional field tests, which should address concerns such as synthesis costs and reaction efficiency.

There have been some studies conducted about the single factor viscoelasticity of polymer solution or wettability effect on the micro-flow mechanism of polymer flooding. In this paper, the flow mechanism of polymer solution in dual heterogeneous reservoir considering the wettability and gravity was studied. The influences of wettability and rock particle shape on flow characteristics were studied based on the characteristics of saturation and pressure distribution. Compared with the simulation results of polymer flooding in three different rock particle shapes porous media, the oil displacement efficiency of the circular particle model is the highest at 91.57%, which is 3.34% and 11.48% higher than that in the hexagonal and diamond models, respectively. The influence of wettability was studied by the circular particle model. The oil displacement efficiency under water-wet conditions was higher than that under oil-wet conditions. The displacement process considering gravity was affected by the crossflow caused by gravity and viscous force, and the micro-oil displacement efficiency was 9.87% lower than that of non-gravity. Considering the wettability, vertical crossflow will be formed. The oil displacement efficiency under water-wet conditions was 3.9% higher than in oil-wet conditions. The research results can not only expand and enrich the micro-flow mechanism of viscoelastic polymer solution, but also provide reference and guidance for polymer flooding scheme design.

The role of indigenous microbial communities in residual oil extraction following a recovery process is not well understood. This study investigated the dynamics of resident microbial communities in oil-field simulating sand pack bioreactors after the polymer flooding stage resumed with waterflooding and explored their contribution to the oil extraction process. The microbial community succession was studied through high-throughput sequencing of 16S rRNA genes. The results revealed alternating dominance of minority populations, including Dietzia sps., Acinetobacter sps., Soehngenia sps., and Paracoccus sps., in each bioreactor following the flooding process. Additionally, the post-polymer waterflooding stage led to higher oil recovery, with hydroxyethylcellulose, tragacanth gum, and partially hydrolyzed polyacrylamide polymer-treated bioreactors yielding additional recovery of 4.36%, 5.39%, and 3.90% residual oil in place, respectively. The dominant microbial communities were previously reported to synthesize biosurfactants and emulsifiers, as well as degrade and utilize hydrocarbons, indicating their role in aiding the recovery process. However, the correlation analysis of the most abundant taxa showed that some species were more positively correlated with the oil recovery process, while others acted as competitors for the carbon source. The study also found that higher biomass favored the plugging of high permeability zones in the reservoir, facilitating the dislodging of crude oil in new channels. In conclusion, this study suggests that microbial populations significantly shift upon polymer treatment and contribute synergistically to the oil recovery process depending on the characteristics of the polymers injected. KEY POINTS: • Post-polymer flooded microbial ecology shows unique indigenous microbial consortia. • Injected polymers are observed to act as enrichment substrates by resident communities. • The first study to show successive oil recovery stage post-polymer flood without external influence.

Significant amounts of oil remain in the reservoir after primary and secondary operations, and to recover the remaining oil, enhanced oil recovery (EOR) can be applied as one of the feasible options remaining nowadays. In this study, new nano-polymeric materials have been prepared from purple yam and cassava starches. The yield of purple yam nanoparticles (PYNPs) was 85%, and that of cassava nanoparticles (CSNPs) was 90.53%. Synthesized materials were characterized through particle size distribution (PSA), Zeta potential distribution, Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), and transmission electron microscopy (TEM). The performance of PYNPs in recovering oil was better than CSNPs, as found from the recovery experiments. Zeta potential distribution results confirmed the stability of PYNPs over CSNPs (-36.3 mV for PYNPs and -10.7 mV for CSNPs). The optimum concentration for these nanoparticles has been found from interfacial tension measurements and rheological properties, and it was 0.60 wt.% for PYNPs and 0.80 wt.% for CSNPs. A more incremental recovery (33.46%) was achieved for the polymer that contained PYNPs in comparison to the other nano-polymer (31.3%). This paves the way for a new technology for polymer flooding that may replace the conventional method, which depends on partially hydrolyzed polyacrylamide (HPAM).

A series of experiments have been carried out on the flooding of microfluidic chips simulating a homogeneous porous structure with various displacement fluids. Water and polyacrylamide polymer solutions were used as displacement fluids. Three different polyacrylamides with different properties are considered. The results of a microfluidic study of polymer flooding showed that the displacement efficiency increases significantly with increasing polymer concentration. Thus, when using a 0.1% polymer solution of polyacrylamide grade 2540, a 23% increase in the oil displacement efficiency was obtained compared to water. The study of the effect of various polymers on the efficiency of oil displacement showed that the maximum efficiency of oil displacement, other things being equal, can be achieved using polyacrylamide grade 2540, which has the highest charge density among those considered. Thus, when using polymer 2515 with a charge density of 10%, the oil displacement efficiency increased by 12.5% compared to water, while when using polymer 2540 with a charge density of 30%, the oil displacement efficiency increased by 23.6%.

Heterogeneous phase composite (HPC) flooding technology that is based on branched-preformed particle gel (B-PPG) is an important technology for enhancing oil recovery in high water-cut reservoirs. In this paper, we conducted a series of visualization experiments under the condition of developed high-permeability channels after polymer flooding, with respect to well pattern densification and adjustment, and HPC flooding and its synergistic regulation. The experiments show that for polymer-flooded reservoirs, HPC flooding can significantly reduce the water cut and increase oil recovery, but that the injected HPC system mainly advances along the high-permeability channel with limited sweep expansion. Furthermore, well pattern densification and adjustment can divert the original mainstream direction, which has a positive effect on HPC flooding, and can effectively expand the sweeping range under the synergistic effect of residual polymers. Due to the synergistic effect of multiple chemical agents in the HPC system, after well pattern densification and adjustment, the production time for HPC flooding with the water cut lower than 95% was significantly prolonged. In addition, conversion schemes, in which the original production well is converted into the injection well, are better than non-conversion schemes in terms of expanding sweep efficiency and enhancing oil recovery. Therefore, for well groups with obvious high-water-consuming channels after polymer flooding, the implementation of HPC flooding can be combined with well pattern conversion and intensification in order to further improve oil displacement.

Polymer flooding has drawn more and more attention in the world for its high incremental oil recovery factor and relative low costs compared with water flooding and other chemically enhanced oil recovery techniques. However, for many oilfields, such as Daqing Oilfield, China, that have already been flooded with polymers, how to further improve recovery remains a big problem. Traditional intralayer, interlayer and plane heterogeneity studies cannot accurately characterize the remaining oil distribution after polymer flooding. To solve this problem, we established a method to quantitatively describe the reservoir\'s architecture. Then, the architecture elements were dissected hierarchically and the interface of each architecture level in Daqing Oilfield was identified. The distribution pattern and development potential of the remaining oil after polymer flooding under the influence of reservoir architecture was analyzed. The results show that, regarding the sedimentary process from north to south in Daqing Oilfield, the channel becomes narrower, the thickness decreases, the point bar\'s width increases and the thickness of the meandering river decreases. The braided bar scale becomes larger and the thickness becomes smaller in the braided river. According to the reservoir\'s architecture, the remaining oil was divided into four categories of plane remaining oil (abandoned channel occlusion type, interfluvial sand body occlusion type, inter-well retention type and well pattern uncontrollable type) and three types of vertical remaining oil (in-layer interlayer occlusion type, rhythm type and gravity type). About 40% of the original oil in place (OOIP) of Daqing Oilfield has not yet been produced, which indicates that there is great potential for development. This study is important for improving oil recovery in polymer-flooded reservoirs.