The electro-oxidation of formamidine disulfide, an important sulfur-containing compound, was simultaneously investigated with on-line high-performance liquid chromatography and cyclic voltammetry. Using a home-made microporous sampler located at the electrode interface, the solution on the electrode surface was in situ sampled and analyzed. The electrochemical scanning was synchronously performed, which allowed the electro-oxidation products to be detected at a given potential. The main products on the surface of platinum electrode were found to be thiourea, formamidine sulfinic acid, cyanamide, and elemental sulfur. Forced convection arising from the sampling played an important role in the electrochemical oxidation. The extraction of electrode surface solution promoted the renewal of reactant and its intermediates, which induced the change of cyclic voltammetry curve. The forced convection also contributed to the redox peak current of the species on the cyclic voltammetry curves through the change of concentration of reactant and its intermediates. This technique can help to explore the reaction mechanism of complex electrochemical reactions.

More than half a century of skeletal muscle research is continuing at Padua University (Italy) under the auspices of the Interdepartmental Research Centre of Myology (CIR-Myo), the European Journal of Translational Myology (EJTM) and recently also with the support of the A&CM-C Foundation for Translational Myology, Padova, Italy. The Volume 30(1), 2020 of the EJTM opens with the collection of abstracts for the conference \"2020 Padua Muscle Days: Mobility Medicine 30 years of Translational Research\". This is an international conference that will be held between March 18-21, 2020 in Euganei Hills and Padova in Italy. The abstracts are excellent examples of translational research and of the multidimensional approaches that are needed to classify and manage (in both the acute and chronic phases) diseases of Mobility that span from neurologic, metabolic and traumatic syndromes to the biological process of aging. One of the typical aim of Physical Medicine and Rehabilitation is indeed to reduce pain and increase mobility enough to enable impaired persons to walk freely, garden, and drive again. The excellent contents of this Collection of Abstracts reflect the high scientific caliber of researchers and clinicians who are eager to present their results at the PaduaMuscleDays. A series of EJTM Communications will also add to this preliminary evidence.

Hematocrit (HCT) tests are widely performed to screen blood donors and to diagnose medical conditions. Current HCT test methods include conventional microhematocrit, Coulter counter, CuSO4 specific gravity, and conductivity-based point-of-care (POC) HCT devices, which can be either expensive, environmentally inadvisable, or complicated. In the present work, we introduce a new and simple microfluidic system for a POC HCT determination. HCT was determined by measuring current responses of blood under 100 V DC for 1 min in a microfluidic device containing a single microchannel with dimensions of 180 μm by 70 μm and 10 mm long. Current responses of red blood cell (RBC) suspensions in PBS or separately plasma at HCT concentrations of 10, 20, 25, 30, 35, 40, 45, 50, 55, 60, and 70 vol% were measured to show feasibility of the microfluidic system for HCT determination. Key parameters affecting current responses included electrolysis bubbles and irreversible RBC adsorption; parameters were optimized via addition of nonionic surfactant Triton X-100 into sample solution and carbonizing electrode surfaces. The linear trend line of current responses over a range of RBC concentrations were obtained in both PBS and plasma. This work suggested that a simple microfluidic device could be a promising platform for a new POC HCT device.

OBJECTIVE: The objective of this study was to investigate the structural properties of a cold-rolled platinum foil used to manufacture multi-electrode spiral nerve cuffs.
METHODS: To attain this objective, 0.03-mm-thick cold-rolled platinum foil strips with 99.99 wt% purity were used. The resistivity measurements were made using a 4-point probe technique in which the strips were subjected to dynamic annealing in an argon atmosphere. The stored energy of platinum was recorded in an argon atmosphere using differential scanning calorimetry (DSC). Finally, the microstructure of the strips was investigated by optical microscopy.
RESULTS: In the resistivity measurements, a small change is observed at ~280°C. This change could be explained as the partial recovery elicited by the decrease of dislocation density. Above 500°C, a significant decrease in resistivity was recorded, and the decrease reached a maximum at ~750°C. These results are consistent with the recrystallization trend detected in DSC, namely the DSC measurement detected very weak heat release during recrystallization, which was actually accumulated during the cold-working. This exothermal peak occurred in the temperature range 380-800°C.

The voltage-operating window for many electrokinetic microdevices is limited by electrolysis gas bubbles that destabilize microfluidic system causing noise and irreproducible responses above ∼3 V DC and less than ∼1 kHz AC at 3 Vpp. Surfactant additives, SDS and Triton X-100, and an integrated semipermeable SnakeSkin® membrane were employed to control and assess electrolysis bubbles from platinum electrodes in a 180 by 70 μm, 10 mm long microchannel. Stabilized current responses at 100 V DC were observed with surfactant additives or SnakeSkin® barriers. Electrolysis bubble behaviors, visualized via video microscopy at the electrode surface and in the microchannels, were found to be influenced by surfactant function and SnakeSkin® barriers. Both SDS and Triton X-100 surfactants promoted smaller bubble diameters and faster bubble detachment from electrode surfaces via increasing gas solubility. In contrast, SnakeSkin® membranes enhanced natural convection and blocked bubbles from entering the microchannels and thus reduced current disturbances in the electric field. This data illustrated that electrode surface behaviors had substantially greater impacts on current stability than microbubbles within microchannels. Thus, physically blocking bubbles from microchannels is less effective than electrode functionalization approaches to stabilize electrokinetic microfluidic systems.