This case report describes the care given to a 58-year-old male patient with severe upper jaw atrophy. The treatment strategy involved utilizing zygomatic implants in conjunction with endosteal implants to rehabilitate both the maxilla and mandible. Temporary prostheses were used during the healing phase, followed by the fabrication and placement of final prostheses. The utilization of zygomatic implants offers advantages such as immediate stabilization and function without the need for extensive bone grafting. This approach not only reduces treatment time and costs but also enhances patient outcomes. Furthermore, guided surgical techniques are increasingly employed to ensure precise implant placement, optimizing prosthetic support.

UNASSIGNED: To evaluate and assess the indicators of bone metabolism markers osteocalcin and β-Cross-Laps in blood serum as a tool for monitoring bone regeneration and determining the time of implantation in patients after mandibulectomy and reconstruction of a free fibular flap with subsequent endosteal implants.
UNASSIGNED: Forty-eight patients in a 6-year period participated in this study, due to resection for tumors. All patients underwent reconstruction with fibula free flap after tumor resection, 4-6 months after osteoectomy, dental implants were installed with further orthopedic rehabilitation. To assess the rate of bone remodeling after transplantation, the content biochemical markers of bone remodeling osteocalcin and β-Cross-Laps serum were determined by enzyme immunoassay.
UNASSIGNED: All 46 fibular free flaps were healed without complications and were survived. A total 326 implants installed, 8 implants failed to osseointegrate, and 6 implants failed after 5 years of loading (peri-implantitis). Success rate of implants after 5 years was 95,7%. In patients before surgery, the mean of osteocalcin levels was 8.5 ng/ml, two months later, there was a sharp increase in the content of osteocalcin by 15.4 ng/ml, after four months reached 24.7 ng/ml, after six months of 28.6 ng/ml, then the indicator began to decrease and after 12 months it was approaching the norm of 14.7 ng/ml. In patients before surgery, the mean level of β-Cross-Laps was 0.76 ng/ml, after two months bone transplantation the mean level of β-Cross-Laps decreased to - 0.65 ng/ml, after four months the indicator increased and reached of 0.98 ng/ml, after six months the indicator was - 1.56 ng/ml, then these indicators began to decrease and after 12 months, approaching normal values of - 0.87 ng/ml. There is a correlation between different concentrations of osteocalcin or β-Cross- Laps and the success rate of implants. Implants were shown to be unsuccessful low concentrations of osteocalcin and high concentrations of β-Cross-Laps in serum.
UNASSIGNED: Studies have shown that the long-term survival and success rates of implants placed in the reconstructed areas may guarantee an excellent prognosis of implant-supported prostheses. Bone markers in blood serum osteocalcin and β-Cross-Laps can be used to evaluate the rate of bone remodeling, which allows you to determine the time of implantation.

To investigate the influence of implant design on the change in the natural frequency of bone-implant system during osseointegration by means of a modal 3D finite element analysis.
Six implants were considered. Solid models were obtained by means of reverse engineering techniques. The mandibular bone geometry was built-up from a CT scan dataset through image segmentation. Each implant was virtually implanted in the mandibular bone. Two different models have been considered, differing in the free length of the mandibular branch (\'long branch\' and \'short branch\') in order to simulate the variability of boundary conditions when performing vibrometric analyses. Modal analyses were carried out for each model, and the first three resonance frequencies were assessed with the respective vibration modes.
With reference to the \'long branch\' model, the first three modes of vibration are whole bone vibration with minimum displacement of the implant relative to bone, with the exception of the initial condition (1% bone maturation) where the implant is not osseointegrated. By contrast, implant displacements become relevant in the \'short branch\' model, unless osseointegration level is beyond 20%. The difference between resonance frequency at whole bone maturation and resonance frequency at 1% bone maturation remained lower than 6.5% for all modes, with the exception of the third mode of vibration in the \'D\' implant where this difference reached 9.7%. With reference to the \'short branch\', considering the first mode of vibration, 61-68% of the frequency increase was achieved at 10% osseointegration; 72-79% was achieved at 20%; 89-93% was achieved at 50% osseointegration. The pattern of the natural frequency versus the osseointegration level is similar among different modes of vibration.
Resonance frequencies and their trends towards osseointegration level may differ between implant designs, and in different boundary conditions that are related to implant position inside the mandible; tapered implants are the most sensitive to bone maturation levels, small implants have very little sensitivity. Resonance frequencies are less sensitive to bone maturation level beyond 50%.

To assess the influence of implant thread shape and inclination on the mechanical behaviour of bone-implant systems. The study assesses which factors influence the initial and full osseointegration stages.
Point clouds of the original implant were created using a non-contact reverse engineering technique. A 3D tessellated surface was created using Geomagic Studio® software. From cross-section curves, generated by intersecting the tessellated model and cutting-planes, a 3D parametric CAD model was created using SolidWorks® 2017. By the permutation of three thread shapes (rectangular, 30° trapezoidal, 45° trapezoidal) and three thread inclinations (0°, 3° or 6°), nine geometric configurations were obtained. Two different osseointegration stages were analysed: the initial osseointegration and a full osseointegration. In total, 18 different FE models were analysed and two load conditions were applied to each model. The mechanical behaviour of the models was analysed by Finite Element (FE) Analysis using ANSYS® v. 17.0. Static linear analyses were also carried out.
ANOVA was used to assess the influence of each factor. Models with a rectangular thread and 6° inclination provided the best results and reduced displacement in the initial osseointegration stages up to 4.58%. This configuration also reduced equivalent VM stress peaks up to 54%. The same effect was confirmed for the full osseointegration stage, where 6° inclination reduced stress peaks by up to 62%.
The FE analysis confirmed the beneficial effect of thread inclination, reducing the displacement in immediate post-operative conditions and equivalent VM stress peaks. Thread shape does not significantly influence the mechanical behaviour of bone-implant systems but contributes to reducing stress peaks in the trabecular bone in both the initial and full osseointegration stages.