The effects of cast iron pipe corrosion on water quality risk and microbial ecology in drinking water distribution systems (DWDSs) were investigated. It was found that trihalomethane (THMs) concentration and antibiotic resistance genes (ARGs) increased sharply in the old DWDSs. Under the same residual chlorine concentration conditions, the adenosine triphosphate concentration in the effluent of old DWDSs (Eff-old) was significantly higher than that in the effluent of new DWDSs. Moreover, stronger bioflocculation ability and weaker hydrophobicity coexisted in the extracellular polymeric substances of Eff-old, meanwhile, iron particles could be well inserted into the structure of the biofilms to enhance the mechanical strength and stability of the biofilms, hence enhancing the formation of THMs. Old DWDSs significantly influenced the microbial community of bulk water and triggered stronger microbial antioxidant systems response, resulting in higher ARGs abundance. Corroded cast iron pipes induced a unique interaction system of biofilms, chlorine, and corrosion products. Therefore, as the age of cast iron pipes increases, the fluctuation of water quality and microbial ecology should be paid more attention to maintain the safety of tap water.

Si-air batteries have a high energy density, high theoretical voltage, and long lifetime, but they present a low anode utilization rate in a potassium hydroxide electrolyte. In this work, a ZIF-8 protective layer was prepared and modulated by a secondary growth method and then applied to protect the Si flat and Si nanowire (NW) anodes of a Si-air battery. By adjusting the conversion ratio, particle size, and crystallinity of ZIF-8 on the Si surface, the contact mode of the Si anode with water and OH- was controlled, thus achieving long-term corrosion and passivation resistance. Si NWs@ZIF-8 exhibited the highest average discharge voltage of 1.16 V, and the Si flat@ZIF-8 anode achieved the longest discharge time of 420 h. This work confirms that ZIF-8 acts as an anode protective layer to improve the properties of Si-air batteries and also provides valuable insights into the protection of Si anodes by MOFs.

Additive manufacturing (AM) of Ti-based biomedical implants is a pivotal research topic because of its ability to produce implants with complicated geometries. Despite desirable mechanical properties and biocompatibility of Ti alloys, one major drawback is their lack of inherent antibacterial properties, increasing the risk of postoperative infections. Hence, this research focuses on the Ti536 (Ti5Al3V6Cu) alloy, developed through Electron Beam Powder Bed Fusion (EB-PBF), exploring bio-corrosion, antibacterial features, and cell biocompatibility. The microstructural characterization revealed grain refinement and the formation of Ti2Cu precipitates with different morphologies and sizes in the Ti matrix. Electrochemical tests showed that Cu content minimally influenced the corrosion current density, while it slightly affected the stability, defect density, and chemical composition of the passive film. According to the findings, the Ti536 alloy demonstrated enhanced antibacterial properties without compromising its cell biocompatibility and corrosion behavior, thanks to Ti2Cu precipitates. This can be attributed to both the release of Cu ions and the Ti2Cu precipitates. The current study suggests that the EB-PBF fabricated Ti536 sample is well-suited for use in load-bearing applications within the medical industry. This research also offers an alloy design roadmap for novel biomedical Ti-based alloys with superior biological performance using AM methods.

Electrochemical impedance spectroscopy (EIS) is a modern and efficient method for the evaluation of the protective abilities of coatings. However, the interpretation of the experimental data is a difficult task. This paper aims to investigate the effect of the addition of a nano clay, Cloesite 30B®, on the barrier properties of an epoxy-based system through electrochemical impedance spectroscopy in an aerated sodium chloride solution. The EIS spectra of the samples analysed showed different evolutions over time. The subsequent processing of spectra using equivalent electrical circuits is an excellent analytical tool and allows the protective capacity of coatings to be assessed. By using this analysis, it was possible to define and comprehend the impact of adding nano clay in different concentrations to the epoxy resin coating. The work has shown the effectiveness of increasing the barrier effect of the coating with this type of nano clay. However, the improvement is linked to obtaining a correct dispersion of nanoparticles. Otherwise, there is the formation of macro-clusters of particles inside the coating. Their appearance can cause a deterioration in coating performance.

Aluminum technical alloys are well known for their outstanding mechanical properties, especially after heat treatment. However, quenching and aging, which improve the mechanical properties, by the formation of Cu-rich zones and phases that are coherent with the matrix and block the dislocation motion, cause uneven distribution of the elements in the alloy and consequently make it prone to corrosion. One method providing satisfactory corrosion protection of aluminum alloys is anodizing. On an industrial scale, it is usually carried out in electrolytes containing chromates that were found to be cancerogenic and toxic. Therefore, much effort has been undertaken to find substitutions. Currently, there are many Cr(VI)-free substitutes like tartaric-sulfuric acid anodizing or citric-sulfuric acid anodizing. Despite using such approaches even on the industrial scale, Cr(VI)-based anodizing still seems to be superior; therefore, there is an urge to find more complex but more effective approaches in anodizing. The incorporation of anions into anodic alumina from the electrolytes is a commonly known effect. Researchers used this phenomenon to entrap various other anions and organic compounds into anodic alumina to change their properties. In this review paper, the impact of the incorporation of various corrosion inhibitors into anodic alumina on the corrosion performance of the alloys is discussed. It is shown that Mo compounds are promising, especially when combined with organic acids.

Rapid corrosion in aqueous solutions of magnesium alloys is one of the major obstacles to their wide application, and coating plays a crucial role in their corrosion protection. Recently, protection- and function-integrated coatings have attracted much attention in the research field of magnesium alloys. In this work, a simple chemical conversion process is proposed to fabricate a composite coating on a magnesium-neodymium alloy through immersion in an aqueous solution made of Ca(OH)2 and NaHCO3. After the immersion process, a coating consisting of two spontaneously formed layers is acquired. The top flower-like layer is composed of Mg5(OH)2(CO3)4∙4H2O, Mg(OH)2 and CaCO3, and the inner dense layer is speculated to be Mg(OH)2. Electrochemical impedance spectroscopy, polarization tests, and hydrogen evolution are combined to evaluate the corrosion resistance in simulated body fluid, simulated seawater solution, and simulated concrete pore solution, which reveals that the coated sample has better corrosion resistance than the uncoated one. After the coated sample is modified with fluorinated silane, a water-repellent surface can be achieved with an average water contact angle of 151.74° and a sliding angle of about 4°. Therefore, our results indicate that effective corrosion protection and potential self-cleaning ability have been integrated on the surface of the magnesium alloy in this study. In addition, the formation mechanism of the self-layered coating is discussed from the viewpoint of the interaction between the substrate and its external solution.

The purpose of this study is to evaluate the corrosion resistance in natural seawater (Năvodari area) of two types of low-alloy carbon steels BVDH36 and LRAH36 by electrochemical methods. The electrochemical methods used were the evolution of the free potential (OCP), electrochemical impedance spectroscopy (EIS), polarization resistance (Rp) and corrosion rate (Vcorr), potentiodynamic polarization (PD), and cyclic voltammetry (CV). The studies were completed by ex situ characterization analyzes of the studied surfaces before and after corrosion such as: optical microscopy, scanning electron microscopy and X-ray diffraction analysis. The results of the study show us that the polarization resistance of the low-alloy carbon steel BVDH36 is higher compared to the polarization resistance of the low-alloy carbon steel LRAH36. It is also observed that with the increase in the immersion time of the samples in natural seawater, the polarization resistance of the BVDH36 alloy increases over time and finally decreases, and for the carbon steel LRAH36 the polarization resistance increases.

The recent rise of 2D materials has extended the opportunities of tuning a variety of properties. Tribo-corrosion, the complex synergy between mechanical wear and chemical corrosion, poses significant challenges across numerous industries where materials are subjected to both tribological stressing and corrosive environments. This intricate interplay often leads to accelerated material degradation and failure. This review critically assesses the current state of utilizing 2D nanomaterials to enhance tribo-corrosion and -oxidation behavior. The paper summarizes the fundamental knowledge about tribo-corrosion and -oxidation mechanisms before assessing the key contributions of 2D materials, including graphene, transition metal chalcogenides, hexagonal boron nitride, MXenes, and black phosphorous, regarding the resulting friction and wear behavior. The protective roles of these nanomaterials against corrosion and oxidation are investigated, highlighting their potential in mitigating material degradation. Furthermore, we delve into the nuanced interplay between mechanical and corrosive factors in the specific application of 2D materials for tribo-corrosion and -oxidation protection. The synthesis of key findings underscores the advancements achieved through integrating 2D nanomaterials. An outlook for future research directions is provided, identifying unexplored avenues, and proposing strategies to propel the field forward. This analysis aims at guiding future investigations and developments at the dynamic intersection of 2D nanomaterials, tribo-corrosion, and -oxidation protection.

The corrosion behavior of 20G and TP347H materials was investigated in molten LiCl-NaCl-KCl salt. The corrosion rates of these materials in molten chloride salt are high and are strongly affected by the alloying surface oxide formation. The 20G shows uniform surface corrosion with almost no protective oxide formation on the surface. In contrast, the austenitic steel TP347H exhibits better corrosion resistance in molten chloride salts due to its high Cr content. Owing to the highly corrosive nature of molten chloride salts, the Cl- in molten salt could react with oxides and alloy, inducing intergranular corrosion of austenitic steel in molten chloride salt environments.