A new colorimetric technique for the measurement of labile phosphate in soils using the diffusive gradients in thin films (DGT) technique was developed in this study. This technique can determine the mass of phosphate accumulated on the precipitated Zr-oxide based binding gel by forming the blue colour following the standard molybdate-ascorbic acid method. The optimal reaction temperature and coloration time were 20 °C (room temperature) and 26 min. After determining a well-fitted calibration equation, the technique was able to measure phosphate concentration up to 2.5 mg/L for 24 h deployment with a detection limit of 10.1 μg/L. Two-dimensional quantitative visualisation of phosphate diffusion in three phosphorus (P) fertilised soils were obtained using the colorimetric technique. The results from the colorimetric DGT technique were compared to the elution DGT technique and Colwell P extraction. The DGT techniques (colorimetric and elution) and Colwell P measurements demonstrated similar patterns of phosphate diffusion in soil. Both DGT techniques showed similar phosphate concentration along the concentric rings around the fertiliser application. A new, convenient, and fast DGT colorimetric technique was developed, and successfully used to measure the distribution of potentially available phosphate in soils. The new technique is less laborious than current techniques as it does not require any pre-treatment of the binding gel layers or heating during scanning, thus providing faster results. Therefore, the technique may be more suitable for in-field applications and can be used to investigate the in situ diffusion of potentially available phosphate from fertilisers, and relate this to the plant uptake of P.

OBJECTIVE: Glenoid bone integrity is crucial for shoulder stability. The purpose of this study was to investigate a non-invasive method for quantifying bone loss regarding reliability and accuracy to detect glenoid bone deficiency in standard two-dimensional (2D) and three-dimensional (3D) computed tomography (CT) measurements at different time points. It was hypothesized that the diameter of the circle used would significantly differ between raters, rendering this method inaccurate and not allowing for an exact estimation of glenoid defect size.
METHODS: Fifty-two shoulder CTs from 26 patients (26 2D-CTs; 26 3D-CTs) with anterior glenoid bone defects were evaluated by 6 raters at time 0 (T0) and at least 3 weeks after (T1) to assess the glenoid bone defect using the ratio method (\"best fit circle\"). Inter- and intra-rater differences concerning circle dimensions (circle diameter), measured width of bone loss and calculated percentage of bone loss (length-width-ratio) were compared in 2D- versus 3D-CT scans. The intraclass coefficient (ICC) was used to determine the inter- and intra-rater agreement.
RESULTS: The mean circle diameter difference in 2D-CT was 2.0 ± 1.9 mm versus 1.8 ± 1.5 mm in 3D-CT, respectively (p < 0.01). Mean width of bone loss in 2D-CT was 1.9 ± 1.7 mm compared to 1.7 ± 1.5 mm in 3D-CT, respectively (p < 0.01). The mean difference of bone loss percentage was 5.1 ± 4.8% in 2D-CT and 4.8 ± 4.5% in 3D-CT (p < 0.01). No significant differences concerning circle diameter, bone loss width and bone loss percentage were detected comparing T0 and T1. Circle diameter, bone loss width and bone loss percentage measurements in 3D-CT were significantly smaller compared to 2D-CT at T0 and T1 (p < 0.01). Agreement (ICC) was fair to good for all indicators of circle diameter (range 0.76-0.83), bone loss width (range 0.76-0.86) and percentage of bone loss (range 0.85-0.91). Overall, 3D-CT showed superior agreement compared to 2D-CT.
CONCLUSIONS: The ratio method varies in all glenoid parameters and is not valid for consistently quantifying glenoid bone defects even in 3D computed tomography. This must be taken into consideration when determining proper surgical treatment. The degree of glenoid bone loss alone should not be used to decide for or against a bony procedure. Rather, it is more important to define a defect size as \"critical\" and to also take other patient-specific factors into consideration so that the best treatment option can be undertaken. Application of the \"best fitting circle\" is a source of error when using the ratio method; therefore, care should be taken when measuring the circle diameter.
METHODS: III.

A novel Zr oxide diffusive gradients in thin films (DGT)-based measurement technique for high-resolution imaging of labile Cr (VI) is introduced in this study. The method is based on the diphenylcarbazide coloration technique for Cr (VI) combined with computer-imaging densitometry, which provides a relation between the accumulated mass of Cr (VI) and the grayscale intensity. The Zr oxide gels show good performance in reflecting the accurate measurement of Cr (VI), independent of the effects of pH, ionic strength, and PO4(3-) concentration. Settling of the Zr-oxide gel was identified as a simple and effective method to suppress leaching of the claret-colored compound out of the gel. In addition, the optimal volume of added coloration reagent was 125 times that of the binding gel and 30min was selected as the optimal time for the chromogenic reaction. The relationship between the accumulated Cr (VI) and grayscale intensity was analyzed under the optimized conditions. The Zr oxide DGT technique could also obviously reflect the heterogeneity of sediment. Consequently, Zr oxide DGT-based coloration is certified to be a robust and suitable tool for providing effective and high-resolution information on bioavailable Cr (VI).