The intricate composition of wastewater impedes the recycling of agricultural and industrial effluents. This study aims to investigate the potential of sisal leaf wastewater (SLW), both water-treated (WTSLW) and alkali-treated (ATSLW), as a substitute for the alkali activator (NaOH solution) in the production of slag-powder- and fly-ash-based composites, with a focus on the effects of WTSLW substitution ratios and sisal leaf soaking durations. Initially, the fresh properties were assessed including electrical conductivity and fluidity. A further analysis was conducted on the influence of both WTSLW and ATSLW on drying shrinkage, density, and mechanical strength, including flexural and compressive measures. Microstructural features were characterized using SEM and CT imaging, while XRD patterns and FTIR spectra were employed to dissect the influence of WTSLW substitution on the composite\'s products. The results show that incorporating 14 wt% WTSLW into the composite enhances 90-day flexural and compressive strengths by 34.8% and 13.2%, respectively, while WTSLW curtails drying shrinkage. Conversely, ATSLW increases porosity and decreases density. Organic constituents in both WTSLW and ATSLW encapsulated in the alkaline matrix fail to modify the composites\' chemical composition. These outcomes underscore the potential for sustainable construction materials through the integrated recycling of plant wastewater and solid by-products.

The smelting processes account for over 80 % of global copper production, generating various slags in large quantities. Most of these slags do not contain the required amounts of valuable metals to justify economic revalorization, yet the concentrations present may negatively affect the environment. In this study, heavy and potentially toxic metals were removed by keeping the liquefied slag at 1300 °C for four hours, while the metals gathering was enhanced by adding silicon-copper compounds. Crystallography, metallography, gravimetric, thermogravimetric, and differential thermal analysis were employed to characterize the slag. Electron probe microanalysis was utilized to examine the distribution of heavy and potentially toxic metals from the original copper slag to the remaining slag and mattes formed in the lower portion of the containing vessel. In all instances, concentrations of the arsenic and zinc were reduced below the detection limit. Moreover, the cumulative concentrations of six heavy metals were reduced from 2400 ppm in the initial slag to 41.7 ppm in the remaining slag when using 30 wt%Si70wt%Cu additive. All potentially valuable or toxic metals gathered in the mattes that had oxygen concentrations about 50 times lower than in the initial slag, at 0.82, 0.56, and 0.68 wt% after the mixing slag with 10 wt%Si90%Cu, 30 wt%Si70wt%Cu, and 50 wt%Si50wt%Cu additives, respectively. Investigated practices can mitigate the threat of heavy and potentially toxic metals associated with the disposal of copper slags while also enabling the recovery of valuable metals and rendering the remaining slag suitable for construction or mine backfill purposes.

The use of hybrid fibre-reinforced Self-compacting concrete (HFR-SCC) has escalated recently due to its significant advantages in contrast to normal concrete such as increased ductility, crack resistance, and eliminating the need for compaction etc. The process of determining residual strength properties of HFR-SCC after a fire event requires rigorous experimental work and extensive resources. Thus, this study presents a novel approach to develop equations for reliable prediction of compressive strength (cs) and flexural strength (fs) of HFR-SCC using gene expression programming (GEP) algorithm. The models were developed using data obtained from internationally published literature having eight inputs including water-cement ratio, temperature, fibre content etc. and two output parameters i.e., cs and fs. Also, different statistical error metrices like mean absolute error (MAE), coefficient of determination ( R 2 ) and objective function (OF) etc. were employed to assess the accuracy of developed equations. The error evaluation and external validation both approved the suitability of developed models to predict residual strengths. Also, sensitivity analysis was performed on the equations which revealed that temperature, water-cement ratio, and superplasticizer are some of the main contributors to predict residual compressive and flexural strength.

Alkali Activated Slag Concrete (AASC) has been a sustained research activity over the past two decades. Its promising characteristics and being environmentally friendly compared to Ordinary Portland Cement made AASC of exceptional interest. However, there is still no firm mix design, for the AASC, that can provide desirable fresh and hardened properties based on the composition of the binder and activator. This research specifically aims to investigate the affecting parameters on the slump and compressive strength of alkali-activated slag/lime-based concrete and provide a better understanding of the potential reasons for these characteristics. The experimental program consisted of two stages; the first stage studied the effect of different binder and activator compositions, and the second stage studied the water-to-binder ratio and binder content effects on the slump and compressive strength of alkali-activated slag/lime-based concrete. The binder and activator compositions were defined through two main parameters, the hybrid factor (HF = CaO/Si2O + Al2O3) and the solution modulus (Ms = SiO2/Na2O). The compressive strength, initial slump, and slump loss were measured to evaluate the different mixes and specify the optimum range of compositions. Based on the studied parameters, the effective range to achieve desirable slump and concrete compressive strength is from HF 0.6 up to 0.8 at Ms 1.5, this would achieve a compressive strength of more than 30 MPa and a slump of 100 mm after 90 min.

The copper slags collected during the excavation of the Early Harappan period site at Kunal in northern India were studied to understand the advancement of smelting technology and the achieved smelting temperature in the furnace by undertaking archaeometallurgical characterisation of the slags. In this research, two types of slags such as slag with glassy appearance and granulated slag were selected for the study. The microscopic structure and distribution of slag components were investigated using optical microscopy and phase determination was done by X-ray diffraction (XRD). Chemical characterization of the slags was conducted using scanning electron microscopy-energy-dispersive X-ray spectroscopy, X-ray fluorescence analysis (XRF) and inductively coupled plasma-mass spectrometry to build a complete chemical profile of the slags. Fayalite and magnetite were the dominant phases in the glassy slag; however, the granulated slag showed the dominance of calcite as secondary phase which reflected the dolomitic stoichiometry of the slag. The presence of dominant fayalite mineral phase as detected by XRD and higher concentration of iron as detected by XRF indicated the reducing environment during the smelting process. In this study, the absence of sulphur is reported which is unique to the ancient copper slag.

In order to alleviate environmental problems and reduce CO2 emissions, geopolymers had drew attention as a kind of alkali-activated materials. Geopolymers are easier access to raw materials, green and environment friendly than traditional cement industry. Its special reaction mechanism and gel structure show excellent characteristics such as quick hardening, high strength, acid and alkali resistance. In this paper, geopolymer pastes were made with metakaolin (MK) and ground granulated blast furnace slag (GGBFS) as precursors. The effects of liquid-solid ratio (L/S) and modulus of sodium silicate (Ms) on the performances of MK-GGBFS based geopolymer paste (MSGP) were characterized by workability, strength and microstructural tests. The regression equations were obtained by central composite design method to optimize the mix design of MSGP. The goodness of fit of all the equations were more than 98%. Based on the results of experiments, the optimum mix design was found to have L/S of 0.75 and Ms of 1.55. The workability of MSGP was significantly improved while maintaining the strength under the optimum mix design. The initial setting time of MSGP decreased by 71.8%, while both of the fluidity and 28-d compressive strength increased by 15.3%, compared with ordinary Portland cement pastes. Therefore, geopolymers are promising alternative cementitious material, which can consume a large amount of MK and GGBFS and promote green and clean production.

It is thought that geopolymers are easy to carbonate, especially when they are cured in ambient temperatures. Matrix gel\'s composition and microstructure, and new products of geopolymers (GPs) after carbonation were investigated in this study on the basis of XRD and SEM-EDS measurements and ternary diagram analysis, which were prepared from low-lime fly ash (FA) and ground granulated blast-furnace slag (GGBS) alone or a blend, as a precursor. The specimens were hardened in a 20 °C environment with alkali activator solution (S/N = 1.1 in mole), followed by storage under sealing or accelerated carbonation. XRD patterns show that carbonation products were nahcolite for the sole FA-based GP and calcite for the GPs using GGBS alone or as a blend. The SEM images of carbonated samples show that there were cube-shaped calcite and small calcite particles in the GGBS-based GP, but hail-like particles in the FA/GGBS blend-based GP. The hail-like particles were complexes of calcite and C-A-S-H gels determined by ternary diagram analysis, and were found to plug the top of the pores of the spongy C-A-S-H gels. We also confirmed that combined ternary diagram analysis of S-(C + M + N)-A and A-(C + M)-N are very effective in determining the gel type of a geopolymer, as well as the products and compositional changes after carbonation, in which oxide components of gels are determined by SEM-EDS. In the former diagram, C-A-S-H gels were plotted linearly along the (C + M + N)-albite (Ab) join, while N-A-S-H gels showed a scattered distribution. In the latter diagram, the plots for N-A-S-H and C-A-S-H gels are distributed in different zones. N = Na2O, C = CaO, M = MgO, A = Al2O3, S = SiO2, H = H2O.

Soil excavated during construction and demolition can be utilized to reduce the demand for natural sand in 3D printed constructions. This research attempts to systematically develop 3D printable stabilized earth-based materials using excavated soil (clay content of 42.5 %) as 25 % and 50 % replacement of natural sand, and examine their compressive strength, water permeable porosity, and moisture sensitivity. The effectiveness of two binder systems - Ordinary Portland Cement (OPC) and a combination of OPC and ground granulated blast furnace slag (GGBS used to replace 30 % OPC by mass), was investigated. Non-expansive clay in the soil leads to a steeper reduction in apparent viscosity, 12-15 % higher flow retention, and 50-60 % lower plastic viscosity of soil-based mixes, thus contributing to superior extrusion quality at 35-40 mm lower initial flow than OPC-sand and OPC-GGBS-sand mixes. The addition of GGBS, due to its irregular particle morphologies and interlocking effects, further enhances the shape retention of the printed layers by 8-26 % compared to OPC-soil mortars. The structural build-ups in OPC-soil and OPC-GGBS-soil mortars increase with the increase in clay content, which enabled buildability up to a height of 1.2 m compared to only 0.51-0.55 m for OPC-sand and OPC-GGBS-sand mortars. Higher water demand due to the addition of natural clay increases the porosity of 3D printed OPC-soil mortars, thereby lowering compressive strength and increasing moisture sensitivity. However, a blend of OPC and GGBS substantially reduces the moisture sensitivity of the printed mortars at 28-day age, attributed to better stabilization of clay through hydraulic and pozzolanic action of GGBS. 28-day wet compressive strength of 14-25 MPa is obtained for the printed soil-based mixes depending on the soil dosage and loading direction. In summary, the study provides a feasible solution for the 3D printing of stabilized earth structures with lower demand for natural sand and OPC.

Around 8% of the global carbon dioxide emissions, are generated during cement manufacturing, which also involves significant use of raw materials, leading to adverse environmental effects. Consequently, extensive research is being conducted worldwide to explore the feasibility of utilizing different industrial waste by-products as alternatives to cement in concrete production. Fly ash (FA), Metakaolin (MK), Silica fume (SF), and ground granulated blast furnace slag (GGBS) are potential industrial materials that can serve as cement substitutes in pervious concrete. However, there exist conflicting findings in the literature regarding the impact of industrial supplementary cementitious materials (ISCMs) as partial cement replacements on the physical, mechanical, and durability properties of pervious concrete. The aim of this review is to investigate the feasibility and potential benefits of using ISCMs and compare them as partial cement replacements in the production of pervious concrete. The analysis primarily examines the effect of ISCMs as partial cement replacements on cementitious properties, including properties of ISMCs, mechanical properties, and durability of pervious concrete. The influence of ISCMs primarily stems from their pozzolanic reaction and filler characteristics. SF has the highest reactivity due to its high surface area and amorphous structure, resulting in a rapid pozzolanic reaction. GGBS and FA have moderate reactivity, while MK has relatively low reactivity due to its crystalline structure. Results from various studies indicate that the addition of FA, SF, and MK up to approximately 20% leads to a reduction in porosity and permeability while improving compressive strength and durability due to the filler effect of SF and MK. Incorporating GGBS increases permeability slightly while causing a slight decrease in compressive strength. The range of permeability and compressive strength for pervious concrete incorporating FA, SF, GGBS and MK were 0.17-1.46 cm/s and 4-35 MPa, 0.56-2.28 cm/s and 3.1-35 MPa, 0.19-0.64 cm/s and 8-42 MPa, 0.10-1.28 cm/s and 5.5-41 MPa, respectively, which are in the acceptable range for non-structural application of pervious concrete. In conclusion, it is possible to produce sustainable pervious concrete by substituting up to 20% of cement with FA, SF, GGBS, and MK, thereby reducing cement consumption, carbon footprint, energy usage, and air pollution associated with conventional cement production. However, further research is required to systematically assess the durability properties, long-term behavior, and, develop models for analyzing CO2 emissions and cost considerations of pervious concrete containing ISMCs.

In this study, to improve the compaction quality and parameters of slag, discrete element models of irregular rock particles (10-60 mm) and circular soil particles (5 mm) were established based on on-site slag screening results. The motion of the vibratory roller was captured by coupling the roadbed model with the roller model in a simulation in which the roller vibrated and compacted the slag subgrade. The results indicated that (1) the best compaction was achieved when the small particle content was 40%, the medium particle content was 20%, and the large particle content was 40%. (2) When the slag was dominated by small rock particles, the optimum compaction frequency was 28 Hz, and when large rock particles dominated, the optimum compaction frequency was 33 Hz. (3) Rock particles were the primary particles that experienced stress in the vibration compaction, and the compressive force and displacement depended on the particle size. (4) The longitudinal and vertical displacements and rotation angles of the soil and rock particles were examined. The results of this study are conducive for advancing the understanding of slag compaction and improving the working efficiency and compaction quality of rollers.