OBJECTIVE: To determine the short-term (5 min) initial effects of a high-irradiance light-curing (LC) protocol on light transmission (LT%), radiant exposure (RE) and degree of conversion (DC%) of different bulk-fill resin-based composites (RBCs).
METHODS: Six bulk-fill composites with different viscosities were investigated: OBF (One Bulk Fill, 3 M), EB (Estelite bulkfill,Tokuyama), PFill, PFlow, ECeram and EFlow (PowerFill, Poweflow, Tetric EvoCeram bulkfill, Tetric Evoflow bulkfill, Ivoclar), subjected to different LC protocols: one ultra-high-intensity (3 W/cm2 -3 s via PowerCure LCU) and two conventional (1.2 W/cm2 -10 s and 20 s via PowerCure and Elipar S10 LCUs). Specimens (n = 5) were polymerized within their molds (ϕ5 mm × 4 mm depth) to determine LT% and RE at 4 mm using a MARC-LC spectrometer. For real-time DC% measurements by FTIR, similar molds were utilized. Data were analyzed by one-way ANOVA and Tukey post-hoc tests at 5 % significance.
RESULTS: Regardless of the applied LC protocols, OBF and low-viscosity RBCs (EB, PFlow and EFlow) had the lowest and highest LT%, RE, DC% and RPmax, respectively. RE results of all RBCs were in the same sequence: Elipar-20 s > PCure-10 s > PCure-3 s. DC% of PFill and PFlow displayed no significant difference between the applied LC protocols (p > 0.05). The polymerization kinetic in all materials was well described by an exponential sum function (r2 varied between 0.85 and 0.98), showing a faster polymerization with the PCure-3 s protocol.
CONCLUSIONS: The measurement of LT% and DC% at 5 min gave an insight into the developing polymerization process. The initial response of these bulk-fill composite to a high-irradiation protocol varied depending on their composition and viscosity, being faster for low viscosity materials. Nevertheless, even though multiple resin composites are designed to be efficient during photopolymerization, care should be taken when selecting materials/curing protocol.

This study explores the effect of using dental brushes with or without metacrylate-based modeling resins on long-term color stability and surface topographies of resin-based composites. This study examined the effects of two variables: (1) the type of brush used (Art brush, Micro-brush, or Mylar strip) and (2) the application of a modeling resin (applied or not applied). The specimens were artificially aged through 10,000 cycles of thermocycling and subsequently immersed in coffee for 30 days. Measurements of color and surface roughness were taken at baseline and after the aging, using a non-contact profilometer for surface roughness and a spectrophotometer for color. Data were analyzed using paired t-tests and one-way ANOVA. Resin-based composites smoothed with dental brushes or micro brushes without modeling resins exhibited lower color change (ΔE) than other groups. Paired t-tests revealed significant differences in average surface roughness (Ra) and valley depth (Rv) for each surfacing technique before and after aging (p ⩽ 0.01). The root means square average of the profile heights (Rq) significantly increased in the control and micro-brush groups (p ⩽ 0.01). In conclusion, the use of brushes in resin-based composites placement does not increase the susceptibility to staining. Instead, the inclusion of resin modeling contributes to discoloration over time.

BACKGROUND: This study aimed to compare the effects of different energy drinks on the surface roughness, weight loss, and color change of various bioactive restorative materials.
METHODS: Charisma Diamond One, Activa™ BioActive Restorative, Activa™ Presto™ and Equia Forte HT Fil samples were prepared using plastic molds (8 × 2 mm) (n = 10/groups). After polishing, the samples were weighed, their colors were recorded using a spectrophotometer according to the CIEDE2000 system, and their surface roughness was measured using a profilometer. The samples were immersed in Powerade, Burn, Monster and distilled water for 7 days. After immersion, all the measurements were repeated. Statistical analyses were performed using the Wilcoxon signed-rank test and the Mann‒Whitney U test (p < 0.05).
RESULTS: All energy drinks roughened the surface of Equia Forte HT Fil (p < 0.05). Powerade and Monster increased the Ra of all materials after 7 days (p < 0.05). Burns affected all materials except the Activa Bioactive (p < 0.05). Significant weight loss was observed in the Equia Forte group after immersion in all the energy drinks, whereas no weight loss was observed in the other groups. According to the color measurements, ΔE00 values were greater in the Burn and Monster groups, except for the Equia Forte HT Fil group (p < 0.05).
CONCLUSIONS: Energy drinks affected bioactive materials to varying degrees. The glass hybrid material was the most affected, and the bioactive restorative materials based on the resin matrix were the least.

This study investigates the tribological properties of resin composites reinforced with the fillers of glass powder and micro-bubbles. Resin composites were prepared with varying concentrations from 1% to 5% wt of fillers. Tribological tests were conducted using a block-on-ring scheme under dry friction conditions. The measurements of friction coefficient and wear values were performed under variable rotation speeds and loading conditions. The study showed that resin composites with 2-3% glass powder fillers and resin composites with 3-4% micro-bubbles exhibited optimal tribological properties. The resin glass powder modifications reduce the wear by 63% and resin micro-bubbles reduce wear by 32%. SEM analysis of the surfaces revealed surface imperfections and structural damage mechanisms, including abrasive and fatigue wear. The study concludes that specific filler concentrations improve the friction and wear resistance of resin composites, highlighting the importance of material preparation and surface quality in tribological performance. The increased wear resistance on both composites would hopefully expand the usage of additive manufactured composite, namely industrial moving components such as polymer gear, wheel, pulley, etc.

The restoration of endodontically treated teeth (ETT) remains a significant challenge in modern dentistry. These teeth often suffer from substantial structural damage due to both the original pathology and the invasive nature of endodontic procedures. Consequently, ETT are more susceptible to fractures compared to vital teeth, necessitating restorative strategies that can effectively restore both function and aesthetics while minimizing the risk of failure. In recent years, advances in adhesive dentistry and the development of high-strength ceramics have further expanded the restorative options for ETT. Bonded restorations have gained popularity as they preserve more tooth structure and enhance the overall strenght of the tooth-restoration complex. The choice of restorative material and technique is influenced by numerous factors, including the amount of remaining tooth structure, the functional requirements of the tooth, and the aesthetic demands of the patient. Despite the plethora of available materials and techniques, the optimal approach to restoring ETT remains a topic of ongoing research and debate. In this comprehensive review, the current state of and recent advances in restoring damaged endodontically treated teeth are explored. Numerous therapeutic options exist, involving a wide range of materials. This article aims to present the biomaterial advancements of the past decade and their applications, offering alternative approaches to treating damaged ETT with the goal of prolonging their retention on the dental arch and serving as a valuable resource for dental practitioners who face this issue daily.

BACKGROUND: The temperature changes, chemical agents, and brushing activity that resin composite restorations are exposed to in the oral environment can cause changes in surface roughness. In this study, the aim was to investigate in vitro the clinical one-year surface roughness changes of different types of composites (flowable or conventional) from the same companies by subjecting them to immersion in solutions, brushing, and thermal cycling procedures to simulate intraoral conditions.
METHODS: Four different resin composite brands were included in the study using both their conventional (Charisma Smart, 3M Filtek Ultimate Universal, Omnichroma, Beautifil II) and flowable resin composites (Charisma Flow, 3M Filtek Ultimate Flowable, Omnichroma Flow, Beautifil Flow Plus F00), giving 4 groups with 2 types of resin composite in each. 40 samples were prepared for each group/resin type, for a total of 320 samples. After initial surface roughness measurements by a mechanical profilometer, the samples were divided into 4 subgroups (n = 10) and immersed in solutions (distilled water, tea, coffee, or wine) for 12 days. The samples were then subjected to 10,000 cycles of brushing simulation and 10,000 cycles of thermal aging. Surface roughness measurements were repeated after the procedures. For statistical analysis, the 3-way analysis of variance and the Tukey test were used (p < 0.05).
RESULTS: It was concluded that composite groups and types had an effect on surface roughness at time t0 (p < 0.001). At time t1, the highest surface roughness value was obtained in the Beautifil-conventional interaction. When the surface roughness values between time t0 and t1 were compared, an increase was observed in the Beautifil II and Beautifil Flow Plus F00, while a decrease was observed in the other composite groups.
CONCLUSIONS: Composite groups, types, and solutions had an effect on the surface roughness of resin composites. After aging procedures, it was concluded that the Beautifil group could not maintain the surface structure as it exceeded the threshold value of 0.2 μm for bacterial adhesion.

OBJECTIVE: The biodegradation of methacrylate (MA)-based dental restoratives has been suggested to contribute to a loss of adhesion and subsequent detachment, or secondary caries, both major causes of restoration failure. Previous studies have demonstrated that intermolecular interactions between resin monomers may affect the hydrolytic-susceptibility of composites. Altering the intermolecular interactions by shielding or masking the hydrolytically-susceptible ester groups found in MA monomers could be an effective strategy to mitigate the biodegradation of resin composites. The objective of this work was to assess whether shielding/masking MAs using fluorinated groups could improve the biostability of experimental composites.
METHODS: Eight fluorinated monomers (FM) were synthesized, characterized (1H NMR), and formulated into experimental resin composites (FC, 65 wt%, microfill). FCs were assessed for interactions with water (water contact angle, water sorption, gel fraction), mechanical properties (both compressive and flexural strength and modulus), cytocompatibility, resistance to biodegradation using simulated human salivary esterase (SHSE) and compared to a control composite (CC) without FM.
RESULTS: Integration of FMs was found to generally decrease both the physical and mechanical properties under all incubation conditions when compared to the CC. Additionally, all FCs had a negative influence on composite biodegradation following immersion in SHSE when compared to the CC.
CONCLUSIONS: Shielding/masking MA-esters inherently inserts molecular spaces between the polymer chains within the resin network, and shielding is likely not possible while also maintaining the necessary cohesive forces that regulate the physical and mechanical properties of resin composites. Novel dental resin development should seek to remove/replace vulnerable ester-containing MAs rather that adopting a shielding/masking approach.

BACKGROUND: Zein-incorporated magnesium oxide nanoparticles (zMgO NPs) were found to be effective against the bacteria S. mutans, S. aureus, E. faecalis and C. albicans, and can impart this antimicrobial effect on the resin composite it is integrated with. However, the effect of different light curing systems on the mechanical properties of this novel biomaterial has yet to be investigated. The objective of this study was to assess the effect of light-emitting diode (LED) and quarts-tungsten halogen (QTH) light curing systems on the compressive strength, flexural strength, and microhardness of bulk-fill resin composite modified with zMgO NPs.
METHODS: A Teflon mold was used to fabricate 180 bulk-fill composite samples with concentrations of zMgO NPs at 0%, 0.3% and 0.5% (n = 60). Samples of each group were allocated to light curing by LED or QTH, after which 10 samples of each group were allotted to a mechanical test. Characterization of the specimens was performed by X-ray diffraction, field emission scanning electron microscopy and Fourier transform infrared spectroscopy. Two-way ANOVA and Tukey\'s post-hoc test was conducted at P = .05 to determine significance.
RESULTS: The characterization revealed a uniform distribution of nanoparticles in the matrix and the formation of a new hybrid composite that maintained its properties. The compressive strength of the 0.3% zMgO composite for the QTH group significantly increased, while the remaining groups underwent no significant change. There was no significant difference among the groups for the flexural strength and microhardness tests.
CONCLUSIONS: The modified composites\' compressive strength, flexural strength, and microhardness improved or remained consistent. Long-term clinical studies can further substantiate the enhanced resin composite.
CONCLUSIONS: The modified composite will exhibit similar or improved mechanical properties whether an LED or QTH light cure device is used. The addition of an antimicrobial effect to bulk-fill resin composite will aid in the prevention of secondary caries.

OBJECTIVE: The purpose was to compare the effects of rapid (3 s) and conventional (20 s) polymerization protocols (PP) of mono- and multichip LED curing units (LCU) on shrinkage stress (SS) and monomer elution (ME) in bulk-fill resin-based composites (RBC) with and without addition-fragmentation chain-transfer (AFCT) monomer.
METHODS: Cylindrical (5x4mm) specimens were prepared from two RBCs containing different AFCT monomers (Filtek OneBulk-FOB; Tetric PowerFill-TPF) and one without (Tetric EvoCeram Bulk-TEC). After soaking for 3, 10, and 14 days (75 % ethanol), ME was quantified using standard monomers by High-Performance Liquid Chromatography. SS was measured from the start of polymerization to 5 min using a Materials Testing Machine. The radiant exitance of LCUs was measured using a spectrophotometer. ANOVA and Tukey\'s post-hoc test, multivariate analysis and partial eta-squared statistics were used to analyze the data (p < 0.05).
RESULTS: AFCT-modification significantly decreased ME (p < 0.001). ME was reduced by half by day 10 and by one tenth by the end of the 14-day compared to the 3-day sampling. ME itself was dependent, whereas the percentage of monomers released was independent of the PP used (p > 0.05). FOB showed the lowest SS (p < 0.001), while there was no significant difference between TPF and TEC (p = 0.124). Both ME and SS were significantly influenced by material type and PP.
CONCLUSIONS: The incorporation of the AFCT monomer reduced ME, but this was inversely related to a decrease in exposure time. SS values reduced by rapid PP in parallel with increasing ME values. The utilization of the AFCT molecule in conjunction with an appropriate resin-, initiator-system is of significant consequence for the kinetics of polymerization and the incorporation of monomers into the network.

BACKGROUND: This study aimed to investigate the effect of whitening toothpastes on the color stability and surface roughness of resin composites stained with coffee and cigarette smoke.
METHODS: Seventy-two disk-shaped specimens (6 × 2 mm) of suprananohybrid resin composite were randomly divided into two groups and exposed to coffee and cigarette smoke (n = 36). After staining, the samples randomly divided into four groups according to whitening toothpastes and were brushed for 4 min: Opalescence Whitening (OW); Colgate Optic White (COW); Curaprox Black is White (CPX) and, distilled water (control) (n = 9). Color was measured with spectrophotometer at the initial, after staining, and after brushing, and surface roughness was measured with profilometer at the initial and after brushing. A surface morphology analysis was examined using scanning electron microscopy and atomic force microscopy. The obtained data were statistically analyzed. (p < 0.05).
RESULTS: Cigarette smoke caused a significantly higher color change than coffee in the resin composite (p < 0.05). Brushing with hydrogen peroxide and silica-containing whitening toothpaste showed significant differences in color change (p < 0.05). The lowest whitening effect was found in activated charcoal-containing toothpaste. While all toothpastes increased the degree of surface roughness of resin composites, the highest roughness was caused by whitening toothpastes containing activated charcoal. (p < 0.05).
CONCLUSIONS: The color stability and surface properties of resin composites can be affected by brushing them with whitening toothpaste. The utilization of whitening toothpaste containing hydrogen peroxide can be considered a safe method for increasing the whiteness of discolored resin composites.