BACKGROUND: Osteotomies are routinely incorporated in rhinoplasty, however, the influence of mass, velocity, kinetic energy (KE), and momentum (p) of the mallet on fracture patterns has not been studied.
METHODS: An experimental sledge guillotine setup was designed simulating a mallet strike with adjustable height and mass and 2 mm-thick Sawbone blocks. KE and p were calculated using KE = ½ mass × velocity2 and p = mass × velocity formulas. Fracture lengths and angles were measured.
RESULTS: Ten groups with varying mallet masses and drop heights were tested with 10 bones per group. Fracture length positively correlated with KE (R = 0.542, p < 0.001) and p (R = 0.508, p < 0.001). Fracture angle also positively correlated with KE (R = 0.367, p < 0.001) and p (R = 0.329, p < 0.001). In groups with similar KE, osteotomies with higher p (heavier mallet with slower velocity) had greater fracture lengths (29.31 ± 0.68 vs. 27.68 ± 2.12 mm, p = 0.013) but similar fracture angles (p = 0.189). In groups with similar p, osteotomies with higher KE (lighter hammer with faster velocity) had significantly greater fracture lengths (28.28 ± 1.28 vs. 20.45 ± 12.20 mm, p = 0.041) and greater divergent fracture angles (3.13 ± 1.97° vs. 1.40 ± 1.36°, p = 0.031). Regression modeling of the relationship between KE and fracture lengths and angles demonstrated that cubic followed by logarithmic regression models had the best fits.
CONCLUSIONS: Osteotomy fracture patterns positively correlated with the mallet\'s KE more so than its p, suggesting that the mallet\'s velocity has an increased impact effect than its mass. Clinically, a heavier mallet with a lower velocity will likely generate a smaller fracture length and fracture angle, indicating a more controlled and ideal fracture.
METHODS: NA Laryngoscope, 2024.

OBJECTIVE: To evaluate the effect of osteotomy preparation technique and implant diameter on primary stability and bone-implant interface of short implants (6mm), when placed in bone with high degree of cancellous content.
METHODS: 90 short (S) implants (6 mm) divided in nine groups based on width (Narrow 4.2 mm, Regular 4.8 mm, Wide 5.4 mm) (N,R,W) and osteotomy preparation (Standard, Osteotome, Osseodensification) (ST, OT, OD) and placed in porcine tibia plateau bone samples: Group SN-ST; Group SN-OT; Group SN-OD; Group SRST; Group SR-OT; Group SR-OD; Group SW-ST; Group SW-OT and Group SW-OD. Insertion torque and Implant Stability Quotient (ISQ) were measured. Four implants from each group SNST, SN-OT, SN-OD were evaluated histomorphometrically.
RESULTS: Insertion torque was significantly higher for implants of Group SW-OD compared to Group SW-ST (50.00 ±14.14 Ncm vs 28.00 ±10.85 Ncm, p= 0.005) and Group SW-OT compared to Group SW-ST (46.87 ±17.10 Ncm vs 28.00 ±10.85 Ncm, p=0.026). Insertion torque was significantly higher for implants of Group SW-OD compared to Group SN-OD (50.00 ±14.14 Ncm vs 31.5 ±15.82 Ncm, p=0.04). No significant differences were observed for the percentage of bone, marrow space and connective tissue in contact to the implant surface between studied groups.
CONCLUSIONS: Osteotomy preparation technique at sites with high degree of cancellous content can influence the implant insertion torque for short and wide implants (5.4x6mm). Implant width can influence the insertion torque of short implants placed with the osseodensification technique.

Laminectomy is a commonly performed surgery to decompress the spinal canal to relieve spinal canal stenosis secondary to a variety of etiologies such as degenerative spinal changes, fractures, tumors, vascular lesions, and infections. Advances in technologies have allowed for more precise osteotomies and offer more protection to nearby structures; however, these technologies may not always be available at some facilities. To the best of the authors\' knowledge, we describe an innovative technique to perform laminectomy using a handheld osteotome, which is widely available and at low cost. Our experience with cadavers and a case study shows that the technique appears to be safe and effective and may have the potential to reduce the procedure length of a laminectomy.

The piezo surgery was reported to cause minimal trauma to the soft tissue. The aim of this study was to compare the periorbital edema and ecchymosis after transcutaneous lateral osteotomy in rhinoplasty using 2-mm osteotome versus Piezo scalpel respectively. In a randomized clinical trial and split-mouth-design, we performed primary rhinoplasty in 15 patients (7 men, 8 women; age 18-35 years, mean age 26.6 ± 5.7 years). Transcutaneous lateral osteotomy was performed using a 2-mm osteotome on the one side and a piezo scalpel on the opposite side. We took digital photographs of the face on 1, 3, 7 and 14 postoperative days. Three examiners used a standard 5-point Kara-Gokalan scale to assess the early postoperative periorbital edema and ecchymosis on each side. We found more difficult to use the piezo scalpel via only one incision and found easier to use two stab incisions for inserting the piezo scalpel. The time spend for each osteotomy was similar (P > 0.05). The inter-observer agreement was high (> 0.676). The postoperative edema showed to be significantly different on day 1, 3 and 7 (P-value < 0.05), ecchymosis was much less on piezo side but not significantly. It was more difficult to use piezo scalpel via only one incision. The piezo scalpel showed to reduce the postoperative edema significantly and improved the ecchymosis. Swelling and bleeding could have crossed the midline and blurred the comparison of two sides. However, this is the best design to achieve the highest similarity in study condition. Level of Evidence Level I, therapeutic study.

External auditory exostosis (EAE) is a condition of progressive temporal bone growth into the external auditory canal most commonly from repeat cold water and wind exposure. Several tools have been utilized for EAE excision with varying implications for intra- and postoperative complications. However, comparisons of osteotome and microdrill are made difficult due to the few published cases and intervariability between surgeons. Furthermore, evidence is needed to analyze the safety of novel supplemental tools such as the piezoelectric bone-cutting device.
Retrospective chart review.
Medical clinic and surgery center.
A total of 413 subjects representing 472 ears met the inclusion criteria. Of which 159 ears were operated on using osteotome alone (OA), 271 using osteotome with a drill (OD), and 42 with osteotome with piezoelectric (OP). Charts were analyzed for the most reported intraoperative complications and postoperative symptoms and complications.
There were no significant differences in the rate of tympanic membrane perforations nor in total intraoperative complications between OA, OD, or OP. The OD group contained the only nonperforation intraoperative event. OA had the lowest or near lowest incidence of all symptoms analyzed. OA showed a significantly lower incidence of tinnitus when compared to OD and OP.
We found that OA performed the best, though not statistically significant in most measures, with regard to mitigating rates of complications postsurgery. Our findings suggest OA provides lower risk intraoperatively and postoperatively for patients undergoing transcanal exostosis excision.

UNASSIGNED: To assess and compare complication rates of symptomatic external auditory canal (EAC) exostoses treated with drill versus osteotome canalplasty.
UNASSIGNED: PubMed/Medline, OVID, EMBASE, Web of Science, Google Scholar.
UNASSIGNED: A systematic review and meta-analysis in accordance with PRISMA guidelines and standardized bias assessment using the JBI critical appraisal checklist was performed. Studies containing original outcome data on drill and osteotome canalplasty were included. The primary study outcome was complication rates.
UNASSIGNED: Fifteen studies were included, encompassing 1399 total patients (1788 ears) with 530 and 1258 ears in the osteotome and drill groups, respectively. Ten studies used a drill, 2 used an osteotome, and 3 used both. The most frequently reported complications were tympanic membrane (TM) perforation (osteotome group: 5.3% [95% CI: 1.7%-10.9%]; drill group: 3.8% [1.5%-7.1%]), sensorineural hearing loss (SNHL) (0.69% [0.07%-1.9%]; 4.3% [2.2%-7.0%]), and postoperative stenosis (1.1% [0.0005%-4.3%]; 4.1% [1.9%-7.0%]). Use of the osteotome was associated with a lower rate of SNHL (P < .05) and stenosis (P < .05), and a higher rate of TM perforation (P < .05). Heterogeneity of the studies included in the analyzed complications ranged from moderate to high. Level of evidence in the included studies ranged from 2b to 4 and all studies had an overall low risk of bias.
UNASSIGNED: While an osteotome technique may increase the risk of TM perforation, drill canaloplasty may increase the risk of SNHL and postoperative stenosis in EAC exostectomy. The exact quantity of hearing loss could not be definitively evaluated. Additional research with participant randomization is needed to assess clinical efficacy.
UNASSIGNED: Level 8.

UNASSIGNED: Olecranon osteotomy is employed for the fixation of intraarticular distal humeral fractures. We conducted a prospective, randomised study comparing Chevron\'s osteotomy with olecranon osteotomy by a Gigli saw for exposure of the intraarticular distal humerus in terms of functional outcome and intra-operative ease of the surgery.
UNASSIGNED: Thirty patients with skeletally mature AO/OTA type 13- B and 13-C distal humerus fractures were randomly allocated to Chevron\'s or Gigli saw groups. Each group consisted of a total of 15 patients. Both the groups were assessed on post-operative parameters including arm, shoulder or hand pain, ability to perform certain routine activities, tingling sensations and pain while sleeping.
UNASSIGNED: In the Gigli saw group, 12 patients had no gross limitation of activity and 13 were able to perform moderate activities with ease. Similar results were observed in the Chevron\'s group. The mean difference between the two groups in Oxford Score was 0.60, within the 95% confidence interval and in line with QuickDASH-11 Score.
UNASSIGNED: Chevron\'s technique offers stability and better healing, providing a larger surface area for bone union. However, it is challenging and time-consuming. Also, literature suggests that the Gigli saw has multiple benefits, saves time and effort, and heals by switching blood supply from centrifugal to centripetal post-operatively. Our study suggests that both Chevron\'s technique and the use of the Gigli saw are effective in distal humeral intra-articular fractures as assessed by multiple parameters. Hence both techniques can be equally used depending on the surgeon\'s preference.

UNASSIGNED: Total hip arthroplasty (THA) is frequently performed in patients with end-stage hip disease. Periacetabular osteophytes are common during THA; however, these osteophytes should be removed intraoperatively to avoid potential impingement between osteophytes and femoral prostheses and decrease dislocation risk. There are no current standard procedures or surgical technique criteria to remove these osteophytes. Osteophytes around the acetabulum are usually removed with an osteotome, yet this presents certain disadvantages. Hence, this study aimed to introduce a novel and more efficient technique than the aforementioned one, the SH-9Hospital acetabular edge file.
UNASSIGNED: Fifty-four patients (54 hips) who underwent primary THA using osteotome and the SH-9Hospital acetabular edge file to remove periacetabular osteophytes intraoperatively were retrospectively studied. Clinical and radiographic data were obtained for all patients intra- and postoperatively.
UNASSIGNED: The mean osteophyte removal time was 274.6±102.7 s and 51.3±21.1 s in the osteotome and SH-9Hospital acetabular edge file groups, respectively. Intraoperative images and postoperative radiographs showed that acetabular osteophytes were removed thoroughly and precisely by the acetabular edge file and that there was no iatrogenic injury and prostheses malposition in both groups.
UNASSIGNED: The SH-9Hospital acetabular edge file was a novel, efficient, highly precise, and repeatable method for removing periacetabular osteophytes in patients undergoing total hip arthroplasty.

UNASSIGNED: Trans-crestal sinus lift procedures are well established.
UNASSIGNED: to retrospectively analyse the efficacy of a flapless trans-crestal maxillary sinus floor elevation and simultaneous dental implant placement based on the Localised Management of Sinus Floor (LMSF) technique suitable for cases with sufficient width of keratinized tissue and of crestal bone but insufficient vertical dimensions of the bone below the sinus.
UNASSIGNED: 71 sinus elevations with simultaneous implant placement were performed on 52 consecutive patients. Following an initial pilot bur transmucosal perforation, the Magnetic Mallet was used with progressively larger osteotomes. The mallet osteotomes are initially directed palatally, towards the cortex of the medial wall of the sinus, below the palato-nasal recess (PNR) and then redirected in a more vertical direction to create the final osteotomy for implant placement.
UNASSIGNED: No significant complications were reported in the post-operative phase. The cumulative success rate during the observation period was 95%. All successful implants were successfully loaded with metal-ceramic or monolithic zirconia crowns and bridges and remained in function during the observation period.
UNASSIGNED: Flapless Localised Management of Sinus Floor (LMSF) is a safe and effective surgical technique with minimal risks and with the advantage of low morbidity. Also, only native bone is used for augmentation and there is no need for additional grafting.

UNASSIGNED: To investigate the efficacy of Ultrasonic Bone Scalpel (UBS) in thoracic spinal stenosis (TSS) in comparison to traditional technique.
UNASSIGNED: A total of 55 patients who had undergone conventional surgery (Group A) are compared with 45 patients of UBS (Group B) in TSS. The primary outcome measure of Modified Japanese Orthopaedic Association score (m JOA) with neurological complications and dural injury were assessed. Secondary outcome measures of total blood loss (TBL), time duration of surgery (ORT) and length of hospital stay (LHS) were analysed.
UNASSIGNED: The pre-operative mJOA score 5.00(4.00-6.00) in the group A and 5.00(4.00-6.00) in the group B improved to 7.00(7.00-8.00) in the group A and 9.00(9.00-10.00) in the group B, respectively (P<0.001) at final average follow-up of 117.55 months for group A and 75.69 months in group B. More significant grade of myelopathy improvement and mJOA recovery rate (RR) were noted in group B. The TBL, ORT and LHS were more favourable in group B as compared to group A (p<0.0001). The group A had 9 (16.36%) neurological deficits compared to 2 (4.44%) in group B (p<0.001). Dural tears occurred in both groups (A=11, B=9). It was more frequent and not repairable in group A but without significant statistical difference.
UNASSIGNED: UBS can reduce neurological deficits and improve outcomes in TSS. Secondarily, reduced blood loss, lesser surgical time and reduced LHS are significant added advantages of this new technology.