Over the past few decades, there has been a growing trend in designing multifunctional materials and integrating various functions into a single component structure without defects. This research addresses the contemporary demand for integrating multiple functions seamlessly into thermoplastic laminate structures. Focusing on NiTi-based shape memory alloys (SMAs), renowned for their potential in introducing functionalities like strain measurement and shape change, this study explores diverse surface treatments for SMA wires. Techniques such as thermal oxidation, plasma treatment, chemical activation, silanization, and adhesion promoter coatings are investigated. The integration of NiTi SMA into Glass Fiber-Reinforced Polymer (GFRP) laminates is pursued to enable multifunctional properties. The primary objective is to evaluate the influence of these surface treatments on surface characteristics, including roughness, phase changes, and mechanical properties. Microstructural, analytical, and in situ mechanical characterizations are conducted on both raw and treated SMA wires. The subsequent incorporation of SMA wires after characterization into GFRP laminates, utilizing hot-press technology, allows for the determination of interfacial adhesion strength through pull-out tensile tests.

Glass fiber-reinforced polymer (GFRP) laminates are used in many applications because of their availability, high mechanical properties, and cost-effectiveness. Fiber defects in the form of waviness or wrinkles can occur during the production of multilayered laminates. When curved laminates of significant thickness are produced, the likelihood of such defects increases. Studies have confirmed that fiber deformation during manufacture leads to a reduction in the mechanical properties of laminates. Therefore, early detection of such defects is essential. The main part of this paper deals with research into the possibility of using active infrared thermography to detect wrinkles in curved multilayered GFRP laminates. The size of the artificial wrinkles was assessed by analyzing scans and microimages. The shape deformations of the samples were evaluated by comparing the samples with the mold and the assumed nominal shape. The influence of the out-of-autoclave manufacturing process on the reduction in wrinkles formed without significantly affecting the internal structure of the laminate is presented in this work. This research demonstrated the ability to detect wrinkles in thick curved laminates using active infrared thermography. However, it also showed how the interpretation of the thermographic results is affected by the curvature of the structure, the lack of uniform heating, and the configuration of the thermographic setup.

Degradation of polymer composites is a significant problem in many engineering aspects. Due to the interaction of various degradation factors during the exploitation of composites, a synergistic effect of destruction is observed. The article describes the phenomena occurring in glass fiber reinforced polyester laminates under the influence of ultraviolet radiation (UV) in an aquatic environment. The laminates were exposed to UV-A, UV-B and UV-C radiation for 1000 h in free-air and underwater conditions. During the test, the materials were immersed at stable depth of 1 mm and 10 mm, respectively. The three-point bending tests performed on the samples after being exposed to UV showed an increase in the flexural strength of the composites. Simultaneously, degradation of the outer surface layer was observed. The degradation removed the thin resin film from the surface which resulted in a direct exposure of the reinforcing fibers to the environment. The transformations taking place in the deeper layers of the composite increased the mechanical strength due to the additional cross-linking reactions excited by the energy arising from the radiation. Moreover, the formation of polymer structures from free styrene remaining after the technological process and the occurrence of free radical reactions as a result of the cage effect was also observed.

This study presents the option of an effective low-impact energy dissipating material applied to GFRP (glass fiber reinforced plastic) composite laminates using auxectic technology in the case of planing hull vessels that use the same high-speed light materials that repeatedly impact the surface of the water when sailing, producing a slamming phenomenon. Research shows that the option to modify the laminate with an auxectic layer protects the laminate from damage. This work proposes the manufacturing of dissipative layers, introduced in laminates made with a polymeric matrix and fiberglass reinforcement, which are evaluated with weight drop tests under different impact energies. The data are collected and processed by a unidirectional gravitometer that gives the acceleration values of the impactor. The tests compare unmodified panels with modified panels, showing that the energy absorbed by the unmodified panel is greater at equal energy levels. The returned energy comparison curve is shown, and the benefits of its use are presented.