OBJECTIVE: This study aimed to evaluate the dentin bond performance of various resin luting cement (RLC) systems combined with universal adhesives in different luting strategies.
METHODS: Three self-adhesive resin luting cements (SRLCs) were used with universal adhesives as primers. Twelve specimens per group were prepared to measure shear bond strength (SBS) under distinct luting strategies in etch-&-rinse and self-etch modes. Regarding luting strategies, the bonded specimens were categorized into four groups based on tooth primer application and the curing mode of the SRLC paste: (i) with light irradiation of the tooth primer (wL) + dual-cure mode (DC) of the SRLC paste, (ii) wL + self-cure mode (SC) of the SRLC paste, (iii) without light irradiation of the tooth primer (woL) + DC mode of the SRLC paste, and (iv) woL + SC mode of the SRLC paste. Specimens were also subjected to different storage conditions: 24 h in water (baseline condition) and 10,000 cycles of thermal cycling.
RESULTS: Luting strategy, storage condition, and SRLC system type significantly influenced dentin SBS values in both etching modes. Notably, certain SRLCs exhibited significantly higher dentin SBS when the primer was light-irradiated compared with no primer irradiation.
CONCLUSIONS: Most SRLCs demonstrated higher dentin bond strength with light-irradiated primers, suggesting potential enhancement of dentin bond performance via primer light irradiation.

Objectives: This study aimed to investigate the effect of different reinforcement techniques on the push-out bond strength of fiber posts to over-flared root canals. Materials and Methods: Forty-eight extracted human single-canal premolars were endodontically treated, over-flared, and randomly divided into four groups (N=12) including SARC: luting with self-adhesive resin cement, DCC: luting with dual-cure core build-up resin composite, CRR: relining root canal walls with bulk-fill resin composite, and DAP: relining fiber post with bulk-fill resin composite. After 24 hours, the roots were sectioned to obtain three cervical, middle, and apical 3mm slices. The push-out test was performed and failure pattern was examined. Kruskal-Wallis and post-hoc Dunn-Bonferroni tests were used for statistical analysis (P<0.05). Results: In all three regions, the lowest and highest bond strength was found in the SARC and DAP groups, respectively. In the middle region, there was a statistically significant difference between the bond strength of the SARC group and that of the DCC (P=0.044), CRR (P=0.021), and DAP (P<0.001) groups. There was no significant difference in the apical region. The lowest bond strength was observed in the apical region, and the highest was related to the cervical region. Adhesive failure was the most common failure pattern in all groups. Conclusion: Based on our results DCC, CRR and DAP methods increased bond strength in the middle and cervical sections of over-flared root regions. Considering that DCC is the easiest and most practical method, we propose that CRR and DAP can be replaced with this method in clinical procedures.

OBJECTIVE: The low durability of composite resin restorations can be attributed to the degradation of the resin dentin bonding interface. Owing to the presence of hydrophilic components in the adhesive, the integrity of the resin dentin bonding interface is easily compromised, which, in turn, leads to a reduction in bond strength. The hydrophilic nature of the adhesive leads to water sorption, phase separation, and leaching of the resin component. Therefore, hydrophobic adhesives could effectively be used to stabilize the integrity and durability of the resin dentin bonding interface.
METHODS: We synthesized a novel hydrophobic dentin adhesive by partially replacing bisphenol A glycidyl dimethacrylate (Bis-GMA) with a light-curable urushiol monomer. The properties of the produced adhesive, including the degree of conversion, viscosity, contact angle, water sorption/solubility, and mechanical strength, were comprehensively examined and compared to those of the commercially adhesive Adper Single Bond2 as a positive control. The adhesive properties were determined using microtensile bond strength measurements, laser confocal microscopy, scanning electron microscopy observations, and nanoleakage tests. Finally, the novel adhesive was subjected to biocompatibility testing to determine its potential cytotoxicity.
RESULTS: At a light-curable urushiol content of 20 %, the synthesized adhesive exhibited high degrees of conversion and hydrophobicity, low cytotoxicity, good mechanical properties, and outstanding adhesive strength.
CONCLUSIONS: The introduction of the light-curable urushiol into dentin adhesives can significantly enhance their hydrophobic, mechanical, and bonding properties, demonstrating potential to significantly improve restoration longevity.
CONCLUSIONS: The integration of light-curable urushiol has endowed the experimental adhesives with several enhanced functionalities. These notable benefits underscore the suitability of this monomer for expanded applications in clinical practice.

OBJECTIVE: To evaluate the effect of proanthocyanidin-functionalized hydroxyapatite nanoparticles (nHAp_PA) used as pretreatment at different concentrations on the microtensile bond strength (µTBS) and endogenous enzymatic activity (MMPs) on pH-cycled dentin after 24 h and 6 months of artificial aging.
METHODS: Fifty human sound dentin blocks were randomly assigned to 5 groups (n = 10): (i) negative control (no treatment); (ii) positive control (pH-cycling); (iii) pH-cycling + 2% nHAp_PA for 60s; (iv) pH-cycling + 6.5% nHAp_PA for 60s; (v) pH-cycling + 15% nHAp_PA for 60s. A self-etch adhesive was used for bonding procedures before resin composite build-ups. Specimens were tested with the µTBS test after 24 h and 6 months of laboratory storage. The proteolytic activity in each group was evaluated with gelatin zymography and in situ zymography. Data were statistically analyzed (p < 0.05).
RESULTS: At 24 h, the µTBS of the experimental groups were significantly higher than the controls (p ≤ 0.001), and no differences were observed between different concentrations (p > 0.05). Artificial aging significantly decreased bond strength in all groups (p ≤ 0.008); however, nHAp_PA 2% still yielded higher bonding values than controls (p ≤ 0.007). The groups pretreated with nHAp_PA exhibited lower MMP-9 and MMP-2 activities compared to the positive control group and almost the same enzymatic activity as the negative control group. In situ zymography showed that after 6 months of aging, nHAp_PA 2% and nHAp_PA 6,5% decreased enzymatic activity as well as the negative control.
CONCLUSIONS: Dentin pretreatment with nHAp_PA increased the bonding performance of a self-etch adhesive and decreased MMP-2 and MMP-9 activities after 6 months.

The leading cause of composite restoration failure is secondary caries, and although caries is a multifactorial problem, weak, damage-prone adhesives play a pivotal role in the high susceptibility of composite restorations to secondary caries. Our group has developed synthetic resins that capitalize on free-radical polymerization and sol-gel reactions to provide dental adhesives with enhanced properties. The resins contain γ-methacryloxypropyltrimethoxysilane (MPS) as the Si-based compound. This study investigated the properties of methacrylate-based resins containing methacryloxymethyltrimethoxysilane (MMeS) as a short-chain alternative. The degree of conversion (DC), polymerization kinetics, water sorption, mechanical properties, and leachates of MMeS- and MPS-resins with 55 and 30 wt% BisGMA-crosslinker were determined. The formulations were used as model adhesives, and the adhesive/dentin (a/d) interfaces were analyzed using chemometrics-assisted micro-Raman spectroscopy. The properties of the 55 wt% formulations were comparable. In the 30 wt% BisGMA formulations, the MMeS-resin exhibited faster polymerization, lower DC, reduced leachates, and increased storage and loss moduli, glass transition (Tg), crosslink density, and heterogeneity. The spectroscopic results indicated a comparable spatial distribution of resin, mineralized, and demineralized dentin across the a/d interfaces. The hydrolytically stable experimental short-chain-silane-monomer dental adhesive provides enhanced mechanical properties through autonomous strengthening and offers a promising strategy for the development of restorative dental materials with extended service life.

OBJECTIVE: The objective of this in vitro study was to evaluate the shear bond strength (SBS) of several universal adhesives to dentin treated with sodium hypochlorite (NaOCl), and NaOCl followed by ethylenediaminetetraacetic acid (EDTA).
METHODS: Adhese Universal, Scotchbond Universal, Prime & Bond Elect, Prime & Bond Active, and Optibond XTR were included in the study. SBS values were determined in self-etch mode with no pretreatment of the dentin, after a 20-minute exposure of the dentin to 6% NaOCl, and after a 20-minute exposure to NaOCl followed by a one-minute exposure to 17% EDTA. Experimental groups were repeated using a total-etch technique (except Optibond XTR).
RESULTS: Adhesives in self-etch mode had significantly reduced SBS following dentin exposure to NaOCl (P < .05), while with a total-etch technique, only Prime & Bond Active was affected (P < .05). SBS in self-etch mode when NaOCl exposure was followed by EDTA were equal to or higher than negative control values (P < .05). For total-etch groups, Adhese Universal was negatively affected by NaOCl + EDTA exposure (P < .05). Prime & Bond Elect exhibited lower SBS following NaOCl + EDTA exposure when compared to just NaOCl exposure but was not different from the negative control (P < .05).
CONCLUSIONS: For the adhesives tested, the use of 17% EDTA following NaOCl exposure negated the negative effects of NaOCl on SBS in self-etch mode. When used in total-etch mode, results varied significantly, with some adhesives performing better or worse depending on the specific testing condition.

OBJECTIVE: To evaluate the effect of urethane methacrylate precursor (UMP) on the enzymatic resistance of demineralized dentin (DD) matrices.
METHODS: Experimental treatments containing 0 (control), 1, and 5 mmol/L UMP dissolved in an acetone (Ace) solution were formulated. Dentin matrix specimens were demineralized in vitro and immersed in the experimental treatments for 1 h. The treated specimens were then stored in 0.1 mg/mL collagenase solution for 24 h, after which their dry mass loss and hydroxyproline (HYP) release were assessed. The swelling ratios of specimens in each group were also evaluated. The interaction between UMP and the dentin matrix was observed using field-emission scanning electron microscopy (FE-SEM). Endogenous enzyme activity in dentin was evaluated using confocal laser scanning microscopy (CLSM).
RESULTS: Compared with the other treatment groups, treatment with 1 mM and 5 mM UMP-Ace significantly decreased the dry mass loss, HYP release and swelling ratio of the DD matrix (p < 0.05). FE-SEM and CLSM observations showed that treatment with UMP-Ace protected the structure of the dentin matrix and decreased porosity within the dentin-collagen network.
CONCLUSIONS: Treatment with 1 mM and 5 mM UMP-Ace protects DD matrix against collagenase degradation and may be clinically useful for improving the durability of the hybrid layer.

OBJECTIVE: The purpose of this study was to evaluate the effectiveness and strength of three various dentin-bonding agents used with adhesives on primary teeth.
METHODS: The study used 80 recently extracted, healthy human maxillary anterior primary teeth that had undergone physiologic resorption, or over-retention. Teeth were cut to expose a flat dentin surface at a depth of 1.5 mm. All samples were divided into four groups (20 samples in each group) as follows: Group I-Control group, Group II-Primary teeth bonding with 6th-generation bonding agent, Group III-Primary teeth bonding with 7th-generation bonding agent, Group IV-Primary teeth bonding with 8th-generation bonding agent. All of the samples\' dentinal surfaces were covered with composite resin using a Teflon mold after adhesive had been applied. A universal testing machine (INSTRON) was used to assess the shear bond strength. Data were collected and statistically analyzed.
RESULTS: The maximum mean shear bond strength was found in 8th-generation bonding agent (30.76 ± 0.16), followed by 7th-generation bonding agent (26.08 ± 0.21), 6th-generation bonding agent (25.32 ± 0.06), and control group (6.18 ± 0.09). Statistically significant difference was found between the three different bonding agents (p < 0.001).
CONCLUSIONS: On conclusion, the 8th-generation bonding agent demonstrated a greater shear bond strength to dentin than the 7th and 6th-generation bonding agent.
CONCLUSIONS: The emergence of different bonding techniques to the market improves the durability and quality of restorations. An effective bonding to the tooth would also reduce bacterial penetration, marginal microleakage, possibility of pulpal inflammation preserve tooth structure, and postoperative sensitivity by allowing less cavity preparation. How to cite this article: Alqarni AS, Al Ghwainem A. Assessment of the Efficacy and Bond Strength of Different Dentin-bonding Agents with Adhesives on Primary Teeth: An In Vitro Study. J Contemp Dent Pract 2024;25(4):342-345.

This study evaluated bond strength of glass fiber posts to root dentin using push-out (PO) and diametral compression (DC), testing glycolic acid as a conditioner and varying dentin moisture. An additional aim was to test whether DC can be an alternative test to PO for bond strength assessment. Eighty bovine teeth were divided into eight groups (n = 10) defined by the use of either 37% glycolic acid or 37% phosphoric acid (PA) on moist or wet dentin before bonding with either Adapter SingleBond/RelyX ARC or One Step Plus/Duo-Link Bisco. Each tooth provided discs with an internal diameter of 2 mm, external diameter of 5 mm, and height of 2 mm, which underwent PO and DC. Finite element analysis (FEA) was carried out on 3D models. When analyzing PO results through linear regression, the highest values of bond strength were observed using glycolic acid on wet dentin in the cervical and middle thirds of the teeth. Analyzing DC results, the only statistical influence on values was the dental thirds. The scatterplot of the DC results and the PO bond strength values indicated no relationship between the results of the two tests (r = 0.03; p = 0.64). PO test detected more sensitive changes in bond strength values than DC.

Studies regarding cytotoxic effects attributed to the use of adhesive bonding agents on pulp tissue are not conclusive. To point out whether these materials are safe for clinical use, in vivo exposure of dental pulp to adhesive bonding agents was simulated using an experimental setup in which Human Dental Pulp Stem Cells (hDPSC) are exposed to the action of two kinds of adhesives: self-etching adhesives and two-step bonding agents through a dentine barrier. Cytotoxic effects on these cells were evaluated by MTT assay protocol and fluorescence microscopy, and their results were contrasted to those obtained through Raman spectra taken on single hDPSCs. Overall, no significant cytotoxic effects were observed by combining all the techniques, and cell viability close to 90% was achieved for a dentine barrier of at least 1 mm thick. Moreover, Raman spectroscopy was able to detect structural DNA damage in some dental pulp cells when exposed to two-step bonding agents, suggesting that this technique could be considered a complementary tool with the potential to evaluate cell toxicity beyond cell viability.