This paper discusses efforts made by past researchers to steady the expansive (problematic) soils using mechanical and chemical techniques - specifically with EPS beads, lime and fly ash. Administering swelling of problematic soils is critical for civil engineers to prevent structural distress. This paper summarizes studies on reduction of swelling potential using EPS, lime and fly ash individually. Chemical stabilization with lime and fly ash are conventional methods for expansive soil stabilization, with known merits and demerits. This paper explores the suitability of different materials under various conditions and stabilization mechanisms, including cation exchange, flocculation, and pozzolanic reactions. The degree of stabilization is influenced by various factors such as the type and amount of additives, soil mineralogy, curing temperature, moisture content during molding, and the presence of nano-silica, organic matter, and sulfates. Additionally, expanded polystyrene (EPS) improves structural integrity by compressing when surrounded clay swells, reducing overall swelling. Thus, EPS addresses limitations of chemicals by mechanical means. Combining EPS, lime and fly ash creates a customized system promoting efficient, long-lasting, cost-effective and eco-friendly soil stabilization. Chemicals address EPS limitations like poor stabilization. This paper benefits civil engineers seeking to control expansive soil swelling and prevent structural distress. It indicates potential of an EPS-lime-fly ash system and concludes by identifying research gaps for further work on such combinatorial stabilizer systems.

A degradation mechanism of polystyrene (PS) in mealworms reared on expanded PS (EPS) was investigated by its decrease in molecular weight and change in chemical structure. A 33% decrease in molecular weight was observed for the digested PS in the frass after 1 week of feeding to mealworms. The FT-IR and py-GC/MS spectra of the digested PS showed radical oxidative reactions taking place in the mealworm body. The presence of hydroperoxide, alcohol and phenol groups was confirmed, and dimer fragments of styrene with quinone and phenol groups were obtained. The decrease in molecular weight and the alternation of benzene rings indicated that autoxidation and quinonization via phenolic intermediates occurred simultaneously in the mealworm body. The survival rate of mealworms reared on EPS was higher than that of starved worms, indicating that EPS was a nutrient source. However, no weight gain was observed in mealworms fed EPS alone. Comparison with the mixed diets with bran or urethane foams (PU) indicated that protein, phosphorus and magnesium components absent from EPS were required for mealworm growth.

Insulation products made of expanded polystyrene (EPS) are commonly utilized in buildings. However, Norwegian building regulations restrict the use of such combustible insulation due to an increased risk of fire spread and generation of smoke and toxic gases. Installation of fire protection coverings has been adopted as a mitigation strategy to address these safety risks. Notably, the current regulations lack pre-approved solutions describing what is considered an adequate protection of combustible insulation. The present study investigated the fire protection properties of selected coverings used to protect EPS insulation in inner walls. Eight comparative fire tests were conducted using an indicative fire resistance test furnace. The test specimens consisted of EPS blocks mounted on a wooden frame and covered with one or two layers of selected board coverings. The specimens were positioned vertically within the test furnace, and each fire test lasted for 10 or 15 min. Test results revealed that only two configurations consisting of either two layers of 12.5 mm gypsum boards or a combination of 12 mm oriented strand board (OSB) and 12.5 mm gypsum board showed no evidence of damage to the EPS substrate after a 15-min fire exposure. Consequently, the findings suggest that a total covering thickness of at least 24.5 mm, comprising two layers of boards, is necessary to prevent adverse effects on EPS insulation. Furthermore, fire tests conducted on coverings with introduced damages and defects showed that the affected area around the damages and defects were limited. For the standard EPS substrate, this area extended from 28 mm to 90 mm, while for the fire-retardant EPS substrate from 28 mm to 75 mm after a 10-min fire exposure. These results suggest that minor physical failures in the covering have limited impact on the fire safety of the system.

The current high production of plastics has prompted the exploration of alternative pathways to facilitate recycling, aiming for a progressively sustainable society. This paper presents an alternative and affordable technology for treating waste expanded polystyrene (EPS) mixed with acetone in a 100:1 volume ratio to be used as 3D printing ink for Direct Ink Write technology. In order to optimize the printing parameters, a comprehensive study was conducted, evaluating different needle diameters, printing speeds, and bed temperature values to achieve homogenous pieces and a highly repeatable 3D printing process. Results showed that the main optimum printing parameters were using needles with diameters of 14 to 16 G and printing speeds ranging from 2 to 12 mm/s, which were found to yield the most uniform ribbons. Increasing the bed temperature, despite favoring acetone evaporation, led to the generation of more heterogeneous structures due to void growth inside the printed ribbons. Thus, employing room temperature for the bed proved to be the optimal value. Lastly, a comparative study between the starting material and the EPS after the printing process was conducted using FTIR-ATR and GPC analyses, ensuring the preservation of the original polymer\'s integrity during physical recycling.

Expanded polystyrene (EPS) is a major component of plastic debris in the environment, including coastal and littoral zones. EPS is widely used in various industries including fish farming and aquaculture, which poses a serious potential threat not only to cultured hydrobionts but also to all living organisms, including humans. This paper presents the results of experimental studies on the effects of EPS (0.024 m2/L) on marine mollusks Mytilus trossulus and Tegula rustica, which are typical inhabitants of the upper littoral of Peter the Great Bay (Sea of Japan), belonging to different systematic groups and differing in the type of nutrition. The results of biochemical marker analysis showed the development of oxidative stress processes. Thus, increasing malondialdehyde content relative to control values was registered in the digestive glands of M. trossulus and T. rustica. In the cells of the digestive glands of M. trossulus, integral antioxidant activity decreased more than 1.5 times compared with that of the control. The change in the concentration of protein carbonyls was unchanged in M. trossulus, whereas in T. rustica, there was a 1.5-fold increase. EPS exposure also resulted in significant DNA damage in the studied mollusks-the damage level increased 2.5-fold in M. trossulus and 1.5-fold in T. rustica relative to the control, indicating the genotoxic potential of EPS litters.

Tenebrio molitor larvae, as known as edible insects, has advantages of being rich in protein, and has been recognized as a suitable alternate protein source for broiler and pig feed. Moreover, given their ability to biodegrade polystyrene, a major pollutant, Tenebrio molitor larvae has been proposed as an innovative solution to environmental problems. In the present study, we investigated the toxicity of Tenebrio molitor larvae powder (TMlp) ingested with expanded-polystyrene (W/ eps) through in vitro and in vivo experiments. The objective of this study was to determine whether TMlp W/ eps can be applied as livestock alternative protein source. For in vitro experiments, cytotoxicity test was performed to investigate the effects of TMlp-extract on the viability of estrogen-dependent MCF-7 cells. The possibility of estrogen response was investigated in two groups: Expanded-polystyrene-fed (W/ eps) TMlp group and without expanded-polystyrene-fed (W/o eps) TMlp group. For in vivo experiments, The male Sprague-Dawley rats were divided based on the dosage of TMlp administered and oral administration was performed to every day for 5 weeks. A toxicological assessments were performed, which included clinical signs, food consumption, body and organ weights, hematology, serum chemistry, and hematoxylin and eosin staining of liver and kidney. There were no specific adverse effect of TMlp W/ eps-related findings under the experimental conditions of this study, but further studies on both sexes and animal species differences should be investigated. In conclusion, TMlp W/ eps was considered non-toxic and observed to be applicable as an alternative protein source for livestock feed.

Although foamed plastic insulation is widely used in construction in the Korean market, it is vulnerable to fire. To improve the flame retardancy, the method of flame-retardant coating with the EG in water-soluble state on the surface of expanded polystyrene (EPS) beads has been widely used. However, polystyrene beads coated with a water-soluble flame retardant easily separate the coated flame retardant in manufacturing. In this study is devised a flame-retardant coating and two steps of coating process for adhering the flame-retardant coating film evenly to the surface of the polystyrene bead without exfoliation. It was analyzed whether a flame-retardant EPS (FR-EPS) with excellent flame retardancy could be manufactured using polystyrene beads coated in this way. Ten FR-EPS samples satisfied the HF-1 and V-0 levels in horizontal and vertical burning tests, respectively. The THR of eight FR-EPS samples for ten minutes did not exceed 8 MJ∙m-2 and the maximum HRR did not exceed 200 kW∙m-2 for more than ten consecutive seconds. FR-EPS passed the building material standard of semi-nonflammability in Korean regulations, in contrast to commercial EPS, which have not passed the semi-nonflammability standard. It was also analyzed how effective the designed coating is in this study, comparing it with composites that were planned to improve the flame resistance of polystyrene, as reported in the literature. Flame Retardancy Index (FRI) values of FR-EPS proved the \"excellent\" level and had higher values compared with other polystyrene composites. These results demonstrated that the coated EPS containing a water-soluble flame retardant manufactured from EG and two steps of application with the coating solution achieved fire safety standard regulations.

Postharvest damage, leading to loss and waste, continues to be a significant problem in the fresh produce industry. Trays, designed to reduce fruit-to-fruit contact, are utilized by the apple industry to minimize bruising of whole apples. During distribution, packaged apples are subjected to various supply chain hazards, which may lead to bruising damage. Currently, molded fiber (MF) and expanded polystyrene (EPS) trays transport whole apples from the packhouse to the retail outlet. Mechanical shock, by free-fall drop method, was used to evaluate the performance differences between the two trays and quantify the bruising characteristics of the apples. Results showed that the EPS trays provided better shock protection to the apple as compared to the MF tray, reducing the impact acceleration by more than 70%. Additionally, the bruise susceptibility was 40% less for the apples packaged inside the EPS trays, regardless of drop height. However, apples packaged in the middle layer trays were most susceptible to bruising damage, regardless of tray type.

We investigated the accumulation of litter along a transition gradient from the dunal beaches (B), to the backdunes (BD), to the channels of a coastal wetland (W), considering both the total litter and a sub-category represented by expanded polystyrene (EPS). Using a removal sampling technique carried out in spring (April and May), we hypothesized that: (i) the total accumulation of litter decreases progressively from the dunes to the backdunes to wet environments while (ii) the lighter polystyrene concentrates in the BD-W fringe where the Phragmites australis reedbeds can have a sink role for this polymer. The total litter density showed a significant decrease along the gradient B-BD-W in both months, with an evident collapse between BD and W. Analogously, EPS showed a significant difference in density along the B-BD-W gradient in both months, although with a different pattern: a maximum in the BD and a significant collapse between BD and W. The presence of backdune hygrophilous vegetation (Phragmites australis\' reedbeds) may act as a sink trapping all types of litter in both cases (total litter and EPS). The different accumulation pattern between total litter and the EPS is due to the lower specific weight of the latter polymer: while the generic litter tends to decrease quantitatively moving away from the sea, the lighter EPS is removed by the winds and pushed towards the land, beyond the dune, where it is trapped by the vegetation, thus showing a peak in density in the backdunes. No significant differences were observed between the litter density in the two months (before and after the removal) either considering the total litter and only EPS. This may suggest a continuous supply of litter from the sea, highlighting how clean-ups actions should be carried out with a higher frequency rather than monthly. This may be even more valid in the period of greater frequency of intense weather-marine events (autumn-winter) when a greater quantity of litter is deposited. These are the first data for the Mediterranean regarding a specific role of wetland hygrophilous vegetation as a sink for anthropogenic litter, mainly expanded polystyrene.

Abundant use of plastic materials has increased the amount of microplastics (MPs) and related hazardous chemicals in the marine environment. Hexabromocyclododecanes (HBCDs), brominated flame retardants added to expanded polystyrene (EPS), have been detected in biotic and abiotic samples. In this study, the partition constants of HBCDs between plastics and seawater (KPsw) were determined. Fugacities of HBCDs in EPS, seawater, sediment, and mussels were obtained to determine the directions of the diffusive flux. The fugacities in EPS (fEPS) were greater than those in seawater (fsw), sediment (fsed), and mussels (fswmussel-EPS and fmussel-rock) by three orders of magnitude, indicating that EPS plastics are a significant source of HBCDs. The fmussel-rock of α-HBCD in rock mussels was greater than fsw by factors of 1.7, whereas the fmussel-rock of γ-HBCD was smaller than fsw by factors of 16, indicating the bioisomerization from γ-to α-HBCD. The relatively constant concentration ratio of β-HBCD to the total HBCDs indicated that β-HBCD is a sufficient tracer for determining the diffusive flux. The fsed values of HBCDs were greater than fsw by factors of 17-28, implying a probable advective vertical flow of HBCDs from the EPS plastics, which requires further investigation.