A series of M/NiCo-Ferrite (M: Pt, Pd, Ru, and Rh) nanoparticles were successfully synthesized, through a facile sol-gel auto-combustion followed by impregnation-reduction approach, as a catalyst for hydrogen generation from hydrolysis of NaBH4. All synthesized samples were characterized by XRD, N2 adsorption-desorption method, ICP-OES, FE-SEM, and EDX analysis. Compared to the other samples, it was observed that the Rh/NiCo-Ferrite sample exhibited higher particle distribution and surface area. To evaluate the hydrogen generation rate, the hydrolysis was carried out at a temperature of 35 °C, with an aqueous solution containing 5 wt.% NaBH4 and 3 wt.% NaOH. The experimental findings indicate that the Rh/NiCo-Ferrite sample exhibited a superior rate of hydrogen generation, with an average value of 11,667 mL/min.gcat, compared to the other samples studied. Enhanced catalytic properties may be responsible for its high activity. In addition, the activation energy of hydrolysis of sodium borohydride over the Rh/NiCo-Ferrite sample was 54.5 kJ/mol which is lower than the activation energy of many Ferrite-based catalysts. Moreover, the re-usability test of the Rh/NiCo-Ferrite sample denoted a decline in the catalytic activity after 4 recycling experiments due to the alterations in morphology and the reduction in the quantity of active phase.

This study demonstrated the synthesis of Fe2MnO4 modified by citric acid, a biodegradable acid, using a simple co-precipitation method. Characterization was performed using qualitative analysis techniques such as Fourier-transformed infrared spectroscopy, scanning electron microscopy equipped with energy-dispersive X-ray spectroscopy, X-ray diffraction, selected-area electron diffraction, N2 adsorption-desorption, and zero-point charge. The prepared nanoparticles had a rough and porous surface, and contained oxygenous (-OH, -COOH, etc.) functional groups. The specific surface area and average pore size distribution were 83 m2/g and 5.17 nm, respectively. Net zero charge on the surface of the prepared nanoparticles was observed at pH 7.5. The prepared nanoparticles were used as an adsorbent to remove methylene blue dye from water under various conditions. Using small amounts of the adsorbent (2.0 g/L), even a high concentration of MB dye (60 mg/L) could be reduced by about ~58%. Exothermic, spontaneous, feasible, and monolayer adsorption was identified based on thermodynamics and isotherm analysis. Reusability testing verified the stability of the adsorbent and found that the reused adsorbent performed well for up to three thermal cycles. Comparative analysis revealed that the modified adsorbent outperformed previously reported adsorbents and unmodified Fe2MnO4 in terms of its partition coefficient and equilibrium adsorption capacity under different experimental conditions.

This paper demonstrates the potential of anisotropic 3D printing for alignable carbon nanomaterials. The ferrite-decorated nanocarbon material was synthesized via a sodium solvation process using epichlorohydrin as the coupling agent. Employing a one-pot synthesis approach, the novel material was incorporated into a 3D photopolymer, manipulated, and printed using a low-cost microscale 3D printer, equipped with digital micromirror lithography, monitoring optics, and magnetic actuators. This technique highlights the ability to control the microstructure of 3D-printed objects with sub-micron precision for applications such as microelectrode sensors and microrobot fabrication.

Exploring a convenient, scalable, yet effective broadband electromagnetic wave absorber (EMA) in the gigahertz (GHz) region is of high interest today to quench its expanding demand. Ni-Zn ferrite is considered as a potential EMA; however, their performance study as a scalable effective millimeter-length absorber is still limited. Herein, we investigated EM wave attenuation properties of Ni0.5Zn0.5Fe2O4 (NZF) samples substituting Mn ion in place of Fe3+ as well as Zn2+ within a widely used frequency range of 0.1-9 GHz. Through composition optimization, Ni0.5Zn0.4Mn0.1Fe2O4 (NZM0.1F) EMA demonstrates excellent microwave absorption performance accompanied by simultaneous maximum reflection loss (RL) of -50.2 dB and wide BW of 6.8 GHz (with RL < -10 dB, i.e., attenuation >90%) at an optimum thickness of 6 mm. Moreover, the attenuation constant significantly increases from ∼217 to 301 Np/m with Mn doping. The key contribution arises from magnetic-dielectric properties synergy along with enhanced dielectric and magnetic losses owing to cation chemistry and site occupation in spinel NZF. In addition, porosity is induced in the system by a controlled two-step heat treatment process that promotes total loss with multiple internal reflections of the EM wave. Furthermore, RL is simulated by varying incident EM wave angles for the NZM0.1F sample displaying its angle insensitivity up to 50°. Our results reveal NZM0.1F as a futuristic environment-friendly microwave absorber material that is suitable for practical high-frequency applications.

A novel low-density composite for the absorption of microwaves was prepared by loading La-doped spinel cobalt ferrite (La-CFO) onto biomass carbon (BC) derived from corn stalks using a hydrothermal method. This composite (La-CFO@BC) not only maintained the advantageous properties of low density and abundant porosity, but also exhibited a unique morphology, with La-CFO displaying a carpet-like structure interspersed with dandelion-shaped particles. The incorporation of La-CFO effectively tuned the electromagnetic parameters of the composite, thereby improving its impedance-matching attributes and its ability to absorb microwave radiation. At a frequency of 12.8 GHz for electromagnetic waves and with a thickness of 2.5 mm, La-CFO@BC demonstrated remarkable performance in microwave absorption, attaining a noteworthy minimum reflection (RLmin) of -53.2 dB and an effective absorption bandwidth (EAB) of 6.4 GHz. Furthermore, by varying the thickness of the La-CFO@BC within the range of 1.0 to 5.5 mm, the EAB could be broadened to 13.8 GHz, covering the entire X-band, the entire Ku-band, and a substantial portion of the C-band. This study demonstrated that La-CFO@BC was a promising alternative for electromagnetic wave attenuation, which offered superior performance in microwave absorption.

Intelligent devices, when subjected to multiple interactions, tend to generate electromagnetic pollution, which can disrupt the normal functioning of electronic components. Ferrite, which acts as a microwave-absorbing material (MAM), offers a promising strategy to overcome this issue. To further enhance the microwave absorption properties of ferrite MAM, numerous works have been conducted, including ion doping and combining with other materials. Notably, the microstructure is also key factor that affects the microwave absorption properties of ferrite-based MAM. Thus, this article provides a comprehensive overview of research progress on the influence of the microstructure on ferrite-based MAM. MAMs with sheet and layered structures are also current important research directions. For core-shell structure composites, the solid core-shell structure, hollow core-shell structure, yolk-eggshell structure, and non-spherical core-shell structure are introduced. For porous composites, the biomass porous structure and other porous structures are presented. Finally, the development trends are summarized, and prospects for the structure design and preparation of high-performance MAMs are predicted.

The potential of aerogels as catalysts for the synthesis of a relevant class of bis-heterocyclic compounds such as bis(indolyl)methanes was investigated. In particular, the studied catalyst was a nanocomposite aerogel based on nanocrystalline nickel ferrite (NiFe2O4) dispersed on amorphous porous silica aerogel obtained by two-step sol-gel synthesis followed by gel drying under supercritical conditions and calcination treatments. It was found that the NiFe2O4/SiO2 aerogel is an active catalyst for the selected reaction, enabling high conversions at room temperature, and it proved to be active for three repeated runs. The catalytic activity can be ascribed to both the textural and acidic features of the silica matrix and of the nanocrystalline ferrite. In addition, ferrite nanocrystals provide functionality for magnetic recovery of the catalyst from the crude mixture, enabling time-effective separation from the reaction environment. Evidence of the retention of species involved in the reaction into the catalyst is also pointed out, likely due to the porosity of the aerogel together with the affinity of some species towards the silica matrix. Our work contributes to the study of aerogels as catalysts for organic reactions by demonstrating their potential as well as limitations for the room-temperature synthesis of bis(indolyl)methanes.

Toluene diamine (TDA) is a major raw material in the polyurethane industry and thus, its production is highly important. TDA is obtained through the catalytic hydrogenation of 2,4-dinitrotoluene (2,4-DNT). In this study a special hydrogenation catalyst has been developed by decomposition cobalt ferrite nanoparticles onto a natural clay-oxide nanocomposite (bentonite) surface using a microwave-assisted solvothermal method. The catalyst particles were examined by TEM and X-ray diffraction. The palladium immobilized on the bentonite crystal surface was identified using an XRD and HRTEM device. The obtained catalyst possesses the advantageous property of being easily separable due to its magnetizability on a natural mineral support largely available and obtained through low carbon- and energy footprint methods. The catalyst demonstrated outstanding performance with a 2,4-DNT conversion rate exceeding 99% along with high yields and selectivity towards 2,4-TDA and all of this achieved within a short reaction time. Furthermore, the developed catalyst exhibited excellent stability, attributed to the strong interaction between the catalytically active metal and its support. Even after four cycles of reuse, the catalytic activity remained unaffected and the Pd content of the catalyst did not change, which indicates that the palladium component remained firmly attached to the magnetic support\'s surface.

The need for stable and well-defined magnetic nanoparticles is constantly increasing in biomedical applications; however, their preparation remains challenging. We used two different solvothermal methods (12 h reflux and a 4 min microwave, MW) to synthesize amine-functionalized zinc ferrite (ZnFe2O4-NH2) superparamagnetic nanoparticles. The morphological features of the two ferrite samples were the same, but the average particle size was slightly larger in the case of MW activation: 47 ± 14 nm (Refl.) vs. 63 ± 20 nm (MW). Phase identification measurements confirmed the exclusive presence of zinc ferrite with virtually the same magnetic properties. The Refl. samples had a zeta potential of -23.8 ± 4.4 mV, in contrast to the +7.6 ± 6.8 mV measured for the MW sample. To overcome stability problems in the colloidal phase, the ferrite nanoparticles were embedded in polyvinylpyrrolidone and could be easily redispersed in water. Two PVP-coated zinc ferrite samples were administered (1 mg/mL ZnFe2O4) in X BalbC mice and were compared as contrast agents in magnetic resonance imaging (MRI). After determining the r1/r2 ratio, the samples were compared to other commercially available contrast agents. Consistent with other SPION nanoparticles, our sample exhibits a concentrated presence in the hepatic region of the animals, with comparable biodistribution and pharmacokinetics suspected. Moreover, a small dose of 1.3 mg/body weight kg was found to be sufficient for effective imaging. It should also be noted that no toxic side effects were observed, making ZnFe2O4-NH2 advantageous for pharmaceutical formulations.

Fetal magnetocardiography (fMCG) has proven to be an important tool for the prenatal monitoring of electrical cardiac activity; however, the high cost of superconducting quantum instrumentation (SQUID) poses a limitation for the dissemination of fMCG as a routine clinical technique. Recently, optically pumped magnetometers (OPMs) operating within person-sized, cylindrical shields have made fMCG more practical, but environmental magnetic interference entering through the shield opening substantially degrades the quality of fMCG signals. The goal of this study was to further attenuate these interferences by placing the OPM array within a small ferrite shield. FMCG recordings were made with and without the ferrite shield in ten subjects inside a person-sized, three-layer mu-metal cylindrical shield. Although the fetal signal was slightly attenuated, the environmental interference was reduced substantially, and maternal interference was also diminished. This increased the signal-to-noise ratio significantly and improved the resolution of the smaller waveform components. The performance improvement was highest in the axial direction and compensated for a major weakness of open-ended, person-sized shields. The ferrite shield is especially beneficial for the deployment of triaxial OPM sensors, which require effective shielding in all directions.