BACKGROUND: The purpose of this in vitro study was to compare and evaluate the stress distribution of maxillary first premolar residual crowns restored with post-core crowns, endocrowns and inlay crowns after deep margin elevation, to explore the fitting restoration for residual crowns using finite element analysis.
METHODS: A healthy complete right maxillary first premolar from a male adult was scanned by cone beam computed tomography (CBCT). The finite element model of the tooth was established by reverse engineering software such as Mimics, Geomagic and Hypermesh. On this basis, the residual crown model after deep margin elevation was made, and the experimental group models were divided into three groups, those restored with post core crowns, endocrowns and inlay crowns. Vertical and oblique static loads were applied to the experimental models to simulate the force on the tooth during mastication (the loading position was located in the central fossa of the occipital surface, and the load was 100 N) using Abaqus software.
RESULTS: The peak value and distribution of von Mises stress in each part of the experimental model were observed. After deep margin elevation, the peak dentin von Mises stresses were lower than the tensile strength of normal dentin in the post-core crown, endocrown, and inlay crown groups; the lowest stress results were found in the post-core crown group for the dentin, restoration, enamel, and deep margin elevation (DME) layers under vertical and oblique loading. In terms of stress distribution clouds, the peak stresses in the dentin tissue were located in the apical 1/3 of the root after postcore crown restorations for both loads, while stress concentrations were evident in the cervical and root areas after endocrown and inlay crown restorations; regardless of the load and restoration method, the corresponding stress concentration areas appeared at the junction of the DME and dentin tissue at the loading site of the restorations; CONCLUSIONS: Post-core crowns, endocrowns and inlay crowns can be used to restore residual crowns after deep margin elevation, and post-core crowns can better protect the residual tooth tissue.

BACKGROUND: Multi-rooted teeth with extensive dental defects often face challenges in stability and biomechanical failure. High-performance polymer PEEK materials, with properties closer to dentin, show promise in reducing stress concentration and preserving tooth structure. This report aimed to explore the use of a highly retentive polyetheretherketone (PEEK) for manufacturing custom-made split post and core for the restoration of grossly destroyed endodontically treated molars.
METHODS: A 40-year-old female patient presented with complaints of loss of tooth substance in the posterior mandibular tooth. This case involved the digital design and fabrication of PEEK split post and core to restore multirooted molar with insufficient dental tissue remnants. The restorations were evaluated over a 3-year follow-up using the World Federation criteria (FDI). The restoration was clinically evaluated through intraoral examination, radiographic assessment, and subjective patient satisfaction, and was deemed clinically good according to FDI criteria.
CONCLUSIONS: The outstanding mechanical properties of PEEK, coupled with the structure of the split post, provide an effective treatment option for weakened multirooted teeth. Simultaneously, the restoration configuration effectively addressed the challenge of varying postinsertion directions, and the interlocking mechanism between the primary and auxiliary posts enhanced the stability of the post and core.

This study explores the potential application of computer aided design (CAD)/computer aided manufac-turing (CAM) for one-piece glass fiber posts and cores in restoring tooth defects post-removal of a broken fiber post using a digital guide plate. This paper reports a fractured left upper incisor fiber post removed using a customized needle and digital guide plate. Following root canal retreatment, CAD/CAM integrated fiber post-core and zirconia full crown restoration were completed. The occlusion testing was conducted using the T-Scan Ⅲ system. This study offers insights for managing secondary repair after fiber post fractures.
探讨采用数字化导板去除折断纤维桩后计算机辅助设计（CAD）/计算机辅助制造（CAM）一体化纤维桩核修复牙体缺损的应用前景。本文报道1例左上侧切牙纤维桩折断后采用定制车针及数字化导板引导下拆除，完成根管再治疗后CAD/CAM一体化纤维桩核及氧化锆全冠修复，并采用T-Scan Ⅲ系统进行咬合测试，为纤维桩折断后行二次修复提供参考。.

OBJECTIVE: To evaluate the effect of the labiolingual diameter and construction of an endodontically treated (ET) anterior tooth with crown restoration on stress distribution and biomechanical safety under occlusal loading.
METHODS: Three-dimensional finite element models were generated for maxillary central incisors with all-ceramic crown restorations. The labiolingual diameters of the tooth, defined as the horizontal distance between the protrusion of the labial and lingual surfaces, were changed as follows: (D1) 6.85 mm, (D2) 6.35 mm, and (D3) 5.85 mm. The model was constructed as follows: (S0) vital pulp tooth; (S1) ET tooth; (S2) ET tooth with a 2 mm ferrule, restored with a fiber post and composite resin core; (S3) ET tooth without a ferrule, restored with a fiber post and composite resin core. A total of 12 models were developed. In total, two force loads (100 N) were applied to the crown\'s incisal edge and palatal surface at a 45° oblique angle to the longitudinal axis of the teeth. The Von Mises stress distribution and maximum stress of the models were analyzed.
RESULTS: Regardless of the loading location, stress concentration and maximum stress (34.07~66.78MPa) in all models occurred in the labial cervical 1/3 of each root. Both labiolingual diameter and construction influenced the maximum stress of the residual tooth tissue, with the impact of the labiolingual diameter being greater. A reduction in labiolingual diameter led to increased maximum stress throughout the tooth. The ferrule reduced the maximum stress of the core of S2 models (7.15~10.69 MPa), which is lower compared with that of S3 models (19.45~43.67 MPa).
CONCLUSIONS: The labiolingual diameter exerts a greater impact on the biomechanical characteristics of ET anterior teeth with crown restoration, surpassing the influence of the construction. The ferrule can reduce the maximum stress of the core and maintain the uniformity of stress distribution.

The purpose of this systematic review was to assess the impact of the incomplete ferrule on the fracture of endodontically treated teeth (ETT).
The keywords such as \"incomplete ferrule,\" \"ferrule,\" \"ferrule effect,\" \"residual dentin,\" \"remaining dentin,\" or \"remaining coronal dentin\" were used for searching, and only in vitro studies investigating the incomplete ferrule effect on natural teeth were included.
PubMed, Medline, Embase, Cochrane Library, and Science Direct databases, and manual-searching.
The search strategy yielded 1633 hits, and a total of 19 in vitro studies closely related to the effect of incomplete ferrule on ETT were included.
The presence of an incomplete ferrule may significantly increase the fracture resistance of restored ETT, compared with restored ETT without ferrule. The number of residual axial walls of the incomplete ferrule may have an impact on the fracture resistance and fracture mode. The location of residual axial walls of the incomplete ferrule may affect the fracture resistance but not the fracture mode.
Limited data suggest that the presence of incomplete ferrule has a positive effect on the fracture resistance of restored ETT. An incomplete ferrule can be an alternative for restoring ETT when a complete ferrule is not present. Nevertheless, further high-quality studies are still needed to offer more robust evidence and to take potential confounding factors into account.

This randomized, controlled clinical trial compares the clinical performance of glass-fibre and resorbable polylactic acid (PLA) intracanal posts used to restore carious primary incisors in young patients. The study sample includes 180 primary upper central incisors of 90 children aged 3 to 4 years. All patients were randomly divided into two equal groups of 45 children who received PLA and glass-fibre (GFP) intracanal posts. The clinical assessment of incisor restorations was carried out immediately upon completion and at months 3, 6 and 12 according to the following criteria: anatomical form, marginal adaptation, surface roughness, marginal pigmentation, colour match, secondary caries and contact point. The Gingival Index (GI), the Bleeding Index (Cowell modification; mBI), and bite force (BF) were measured. At the 3-month follow-up, the occlusal BF of patients who received PLA posts was higher than the baseline; the GI and mBI scores were lower, by contrast (p < 0.05). This tendency was even more pronounced 6 and 12 months after the restoration. The incidence of side effects or symptoms (apical inflammation, cervical fracture, loosening of the crown) after the PLA posts was significantly lower than after the GFP (p < 0.05). No statistically significant differences were present between the two groups with respect to colour matching, anatomical form, marginal adaptation, marginal pigmentation, surface roughness, occlusal contact and secondary caries. Based on the results, applying PLA intracanal posts and cyanoacrylate to residual anterior crowns in young children can improve their gingival health, reduce side effects, and increase the likelihood of successful restoration.

BACKGROUND: The selection of post-core material holds significant importance in endodontically treated teeth, influencing stress distribution in the dental structure after restoration. The use of computer-aided design/computer-aided manufacturing (CAD/CAM) glass fiber post-core possesses a better adaptation for different root canal morphologies, but whether this results in a more favorable stress distribution has not been clearly established.
METHODS: This study employed finite element analysis to establish three models of post-core crown restoration with normal, oversized, and dumbbell-shaped root canals. The three models were restored using three different materials: CAD/CAM glass fiber post-core (CGF), prefabricated glass fiber post and resin core (PGF), and cobalt-chromium integrated metal post-core (Co-Cr), followed by zirconia crown restoration. A static load was applied and the maximum equivalent von Mises stress, maximum principal stress, stress distribution plots, and the peak of maximum displacement were calculated for dentin, post-core, crown, and the cement acting as the interface between the post-core and the dentin.
RESULTS: In dentin of three different root canal morphology, it was observed that PGF exhibited the lowest von Mises stresses, while Co-Cr exhibited the highest ones under a static load. CGF showed similar stress distribution to that of Co-Cr, but the stresses were more homogeneous and concentrated apically. In oversized and dumbbell-shaped root canal remnants, the equivalent von Mises stress in the cement layer using CGF was significantly lower than that of PGF.
CONCLUSIONS: In oversized root canals and dumbbell-shaped root canals, CGF has shown good performance for restoration of endodontically treated teeth.
CONCLUSIONS: This study provides a theoretical basis for clinicians to select post-core materials for residual roots with different root canal morphologies and should help to reduce the occurrence of complications such as root fracture and post-core debonding.

The purpose of this in vitro study was to evaluate the internal adaptation, fracture resistance, and fracture pattern of the residual roots and crowns of molars restored with computer-aided design/computer-aided manufacturing (CAD/CAM) glass fiber post-cores, and compare them with three other post-core restorations.
We selected 32 extracted maxillary first molars and divided them into four groups according to the post-core system: traditional casting titanium (Ti) post-cores (TC group); Ti post-cores fabricated with selective laser melting (SLM group); CAD/CAM glass fiber post-cores of the split type (CCS group); and prefabricated glass fiber posts and composite resin cores (PF group). The internal adaptation was analyzed with microcomputed tomography. Teeth were restored with monolithic zirconia crowns and subjected to thermocycling and cyclic loading. A load was applied consistently along the long axis of the tooth until fracture to record the fracture resistance and pattern. For the statistical analysis, one- and two-way analyses of variance, Tukey\'s post hoc and chi-square tests were performed to compare the differences among the groups.
The CCS, TC, and SLM groups exhibited similar internal adaptations across all sections (P < 0.05). The FP group showed good fit with the root canals in the apical and middle sections but a poor fit with those in the cervical section. The fracture resistance was higher in the CCS, TC, and SLM groups compared to the PF group (P < 0.05). The proportions of restorable fractures in the CCS and PF groups were 62.5% and 50%, respectively. Unrestorable fractures were more frequent in the TC and SLM groups at frequencies of 100% and 87.5%, respectively.
The internal adaptation and fracture resistance of the CCS group were similar to those of the TC and SLM groups, and the fracture pattern was mostly restorable, thus meeting the clinical requirements for molar post-core restorations.
CCS can be used to restore residual roots and crowns of molars and exhibit high efficacy in terms of adaptability and mechanical properties. More studies are required to evaluate the effectiveness of CCS.

OBJECTIVE: To evaluate the adaptability between posts and post spaces and the rationality of cores fabricated by two digital custom post-and-core processes.
METHODS: Titanium post-and-cores were fabricated by digital scanning impression technology or digital scanning wax-pattern technology on tooth defect molds of incisors, premolars, and molars, with traditional lost-wax casts of these teeth as the controls. Micro-CT and a laboratory scanner were used to determine intervals between post wall and root canal wall of the root apex, middle, and cervix of each sample in cross-, sagittal, and coronal sections; intervals between the end of post and tooth; diameters of cervical, middle, and incisal part at cross-, sagittal, and coronal sections of each sample, as well as shoulder widths.
RESULTS: The three fabrication processes showed significant differences in intervals between post-and-core prostheses and root canal walls, diameters of all parts of cores, and shoulder widths. Scanning impressions showed significant advantages in the main part of post-and-cores in incisors and premolars, while the scanning wax-pattern process showed obvious inferiorities in premolars and molars. As to core spatial size, values of measured sites in the scanning impression process were closer to the standard than those of the traditional process, while differences between the measured value of the scanning wax-pattern process were much more obvious than in the traditional process.
CONCLUSIONS: The use of digital custom post-and-core scanning impressions improved the rationality and precision of post-and-core dimensions compared with two other processes.

Fiber post bonding failure remains an issue during crown restoration procedures. This experiment examines the bonding effect of combined Er:YAG laser treatment on both root canal and fiber post. Sixty extracted mandibular first premolars were randomly selected and divided into 6 groups (n = 10 per group): G1 (control group): root canal with 2.5% NaClO treatment, no treatment of fiber post; G2: root canal with 2.5% NaClO treatment and fiber post with airborne-particle abrasion; G3: root canal with Er:YAG laser treatment and fiber post with airborne-particle abrasion; G4: root canal with Er:YAG laser treatment, no treatment of fiber post; G5: root canal with 2.5% NaClO treatment, fiber post with Er:YAG laser irradiation; G6: combined Er:YAG laser irradiation of both root canal and fiber post. An Er:YAG laser with a wavelength of 2940 nm was used to treat the fiber post (4.5 W, 450 mJ, 10 Hz for 60 s at 100-μs pulse duration with 100% water cooling) and the root canal (1.5 W, 150 mJ, 10 Hz for 60 s at 100-μs pulse duration with 100% water cooling). When the root canal was treated with the laser, the fiber tip was inserted into the root canal to make a spiral reciprocating motion. Bond strength was analyzed by a micro push-out test. Data were analyzed using both the Tukey test and two-way ANOVA (α = 0.05). Failure modes were observed and counted through a stereo microscope. The root canal and fiber post surface analysis was performed using SEM. The bond strength of G3 and G6 were significantly enhanced compared to those of the other groups (p < 0.05). The SEM analysis showed that the smear layers of groups with root canals subjected to Er:YAG laser irradiation were significantly reduced compared to those of the control group (G1). In groups with fiber posts treated with Er:YAG laser irradiation, the surfaces of the fiber posts exhibited greater surface roughness and a certain degree of epoxy matrix removal. Through the combined Er:YAG laser irradiation of both root canal and fiber post, the bond strength between them was significantly enhanced, which was superior to the individual treatment of either fiber posts or root canal.