Ectodermal dysplasia, a heterogeneous group of rare genetic disorders, is characterized by the aberrant development of ectodermal structures, leading to various clinical anomalies. This case report presents a unique and challenging case of a 33-year-old male with ectodermal dysplasia who underwent Le Fort III advancement and implant rehabilitation surgery to address severe craniofacial and dental deficiencies. This case, characterized by facial dysmorphism, craniofacial anomalies, and the absence of a nasal bone, highlights the complexity of surgical planning required to address these diverse clinical features. The crucial element of this report is the innovative approach to airway management through trans mylohyoid/submental intubation, which successfully navigated the patient\'s aberrant anatomy. Multidisciplinary collaboration played a pivotal role in achieving a holistic and patient-centered approach. By sharing this case, we aim to provide insights into the nuances of managing complex patients with ectodermal dysplasia, emphasizing the importance of individualized care, innovative techniques, and interdisciplinary teamwork to optimize patient outcomes and contribute to advancing medical knowledge.

This report describes maxillary antral pseudocyst drift after maxillary sinus floor augmentation through osteotome sinus floor elevation with simultaneous implant placement. 3D Slicer was used to measure the pseudocyst and maxilla for the placement of the implants; follow-up visits were scheduled at 6, 12, and 22 months. No adverse effects were observed during or after surgery, and all implants exhibited osseointegration without mobility. At 6 months after surgery, the pseudocyst had moved posterolaterally from the preoperative position near the anterior medial maxillary sinus, then returned to its original position at 12 months. However, it had remigrated to the posterolateral position at 22 months. The preoperative volume of the pseudocyst was 3.795 mm3; it was 2.370, 3.439, and 2.930 mm3 at 6, 12, and 22 months after surgery, respectively. The changes in pseudocyst drift and volume did not have a substantial negative influence on the implants, presumably because of cystic attachment and the recurrence of multiple pseudocysts at different locations. The risks associated with changes in a pseudocyst can be avoided, if an appropriate treatment plan is selected.

The aim of this article is to describe how, during the provisional and definitive prosthetic phases, using new digital technologies, it is possible to improve the ergonomics of the prosthetist\'s work and reduce the discomfort of patients, subjecting them to the fewest possible appointments at the dentist. The proposal of a full digital protocol, described by the following case report, for the realization of a definitive prosthetic rehabilitation supported by a reduced number of implants, in fact, allows to considerably reduce the number of appointments and reduce any bias. A 67-year-old male patient presents for the first visit to the Department of Dentistry of the San Raffaele Hospital, wearing a removable upper prosthesis and with the request to heal the aesthetic and functional situation through prosthetics fixed. An initial panoramic radiograph was performed, intra and extra oral photos were taken and also intraoral impressions. A stereo-lithographic models are obtained from intraoral scans, and two total prostheses, upper and lower, were packaged for the provisional post-surgical phase was performed. In accordance with the All-on-4 method 8 implant fixtures were placed. For the final prosthetic phase, the patient underwent only two operative sessions. In the first session, scans were taken with the provisionals in situ, of the patient\'s mucous membranes and with the Scan-abutments in place. In the second session using specific CADSoftware the matching of the STL files of the three scans were created, the opposing arches of the patient were related on a digital articulator, and the milled titanium bars were immediately constructed and finished with the resin. Finally, the definitive prostheses were delivered to the patient without any other test. Digital technology has allowed a clear reduction in working times and costs and has allowed the reduction of stress for patients who undergo invasive and extensive treatments to recover aesthetics and function, and for clinicians who must manage complex cases with fewer appointments possible.

Oral rehabilitation with overdenture on implants of upper jaw must be taken into consideration a variety of anatomical and biomechanical issues. It is possible to provide for rehabilitation with two or more implants, in different positions, solidarizing them with a bar.
The present study involved a patient rehabilitated with 4 Xive implants (Friadent GmbH, Mannheim, Germany) solidarized with a titanium bar crafted with CAD-CAM technology for maximal comfort, precision and structural lightness.
The follow-up was 54 months, with an implant survival of 100%. Based on our clinical evidence, bars engineered with CAD-CAM technology are promising in terms of precision and comfort despite higher costs.