Energy-free passive daytime radiative cooling (PDRC) technology makes it an attractive solution to both the building energy crisis and global warming. Spectrally selective porous polymers have great potential for practical PDRC applications owing to their cooling performance and scalability. A fundamental understanding of the relationship between the cooling performance and pore properties is crucial for guiding future structural designs of high-performance PDRC materials. However, one of the key challenges is achieving uniform nanopores and tailorable pore morphologies in the PDRC coating films. Here we demonstrate a strategy to use advanced metal-organic framework (MOF) nanocrystals as a sacrificial template creating a nanoporous poly(vinylidene fluoride) (PVDF) coating film with uniform-sized nanopores for highly daytime passive radiative cooling. The experimental evidence indicates that nanopores around 400 nm in size, comparable to the wavelength within the ultraviolet and visible spectra, along with an appropriate porosity of 37%, contribute to excellent solar reflectance (94.9 ± 0.8%) and high long-wave infrared emission (92.8 ± 1.4%) in the resulting porous PVDF films. This leads to subambient cooling of ≈9.5 °C and a promising net cooling power of 137 W/m2 at midday under solar intensities of ∼1275 and ∼1320 W/m2. The performance equals or exceeds that of state-of-the-art polymeric PDRC designs, and this general strategy of tailing nanostructures is expected to open a new avenue toward high-performance radiative cooling materials for PDRC applications.

The dilational modulus (E) of polymer films has been commonly measured using the oscillating ring/bubble/drop methods with an external force, and often without specifying the state of the adsorbed film. This study explores an approach where E was determined from the relaxations of surface tension (ST) and surface area (SA) of natural perturbations, in which ST and SA were monitored using a pendant bubble tensiometer. The E of the adsorbed film of PAA (polyacrylic acid) was evaluated for aqueous solutions at CPAA = 5 × 10-4 g/cm3, [MW = 5, 25, and 250 (kDa)]. The E (=dγ/dlnA) was estimated from the surface dilational rate (dlnA/dt) and the rate of ST change (dγ/dt) of the bubble surface from the natural perturbation caused by minute variations in ambient temperature. The data revealed that (i) a considerable time is required to reach the equilibrium-ST (γeq) and to attain the saturated dilational modulus (Esat) of the adsorbed PAA film, (ii) both γeq and Esat of PAA solutions increase with MW of PAA, (iii) a lower MW solution requires a longer time to reach its γeq and Esat, and (iv) this approach is workable for evaluating the E of adsorbed polymer films.

The oral cavity is constantly exposed to contact with an external environment. Pathogens can easily access and colonize it, causing a number of medical conditions that are usually accompanied by inflammation, which in turn require medical intervention and cause the deterioration of wellbeing. The aim of this study was to obtain polymer films that could be a carrier for chlorhexidine, an active substance used in the treatment of inflammation in the oral cavity, and at the same time act as a dressing for the application on the mucous membrane. Combinations of three biocompatible and biodegradable polymers were used to prepare the films. The obtained samples were characterized by assessing their water loss after drying, swelling ability, hygroscopicity and tensile strength. It was shown that the mixture of HPMC and gellan gum or gelatin could be used to prepare transparent, flexible polymer films with chlorhexidine. All tested films showed high hygroscopicity and swelling ability. However, it was observed that the composition containing gellan gum was more suitable for obtaining films with prolonged stay at the site of administration, which predisposes it to the role of a local dressing.

The loose and randomly oriented byproduct (i.e., Zn4(OH)6SO4·xH2O, ZHS) in situ formed on the zinc (Zn) surface is recognized to be the primary cause for dendritic Zn growth and side reactions. Switching the detrimental passivation film into a dense and kinetically favorable solid electrolyte interphase (SEI) is a straightforward strategy to tackle these issues faced by Zn metal anodes but remains largely unexplored. Herein, a new polymer film directly grown on Zn metal through room-temperature plasma-enhanced chemical vapor deposition is proposed to induce the lateral growth of ZHS nanosheets and decrease the Zn2+ desolvation barrier, thereby forming a beneficial composite SEI for suppressing Zn dendrite growth and surface corrosion. As a result of the joint effect, we realize an impressively stable cycling behavior in symmetric cell over 3400 h at 2 mA cm-2. Moreover, full cells also demonstrate prolonged lifespans. This work opens a new avenue for stabilizing Zn metal batteries by turning detrimental ZHS into a favorable interlayer.

The etching of iron alloy items in a H3PO4 solution is used in various human activities (gas and oil production, metalworking, transport, utilities, etc.). The etching of iron alloys is associated with significant material losses due to their corrosion. It has been found that an efficient way to prevent the corrosion of iron alloys in a H3PO4 solution involves the formation of thin complex compound films consisting of the corrosion inhibitor molecules of a triazole derivative (TrzD) on their surface. It has been shown that the protection of iron alloys with a mixture of TrzD + KNCS in a H3PO4 solution is accompanied by the formation of a thin film of coordination polymer compounds thicker than 4 nm consisting of TrzD molecules, Fe2+ cations and NCS-. The layer of the complex compound immediately adjacent to the iron alloy surface is chemisorbed on it. The efficiency of this composition as an inhibitor of iron alloy corrosion and hydrogen bulk sorption by iron alloys is determined by its ability to form a coordination polymer compound layer, as experimentally confirmed by electrochemical, AFM and XPS data. The efficiency values of inhibitor compositions 5 mM TrzD + 0.5 mM KNCS and 5 mM TrzD + 0.5 mM KNCS + 200 mM C6H12N4 at a temperature of 20 ± 1 °C are 97% and 98%, respectively. The kinetic parameters of the limiting processes of hydrogen evolution and permeation into an iron alloy in a H3PO4 solution were determined. A significant decrease in both the reaction rate of hydrogen evolution and the rate of hydrogen permeation into the iron alloy by the TrzD and its mixtures in question was noted. The inhibitor compositions 5 mM TrzD + 0.5 mM KNCS and 5 mM TrzD + 0.5 mM KNCS + 200 mM C6H12N4 decreased the total hydrogen concentration in the iron alloy up to 9.3- and 11-fold, respectively. The preservation of the iron alloy plasticity in the corrosive environment containing the inhibitor under study was determined by a decrease in the hydrogen content in the alloy bulk.

The structure of very thin polymer films formed by strongly adsorbed macromolecules was studied by computer simulation. A coarse-grained model of strictly two-dimensional polymer systems was built, and its properties determined by an efficient Monte Carlo simulation algorithm. Properties of the model system were determined by means of Monte Carlo simulations with a sampling algorithm that combines Verdier-Stockmayer, pivot and reputation moves. The effects of temperature, chain length and polymer concentration on the macromolecular structure were investigated. It was shown that at low temperatures, the chain size increases with the concentration, that is, inversely with high temperatures. This behavior should be explained by the influence of inter-chain interactions.

The aim of this study was to develop a natural nonwoven layer made of cottonized bleached flax and cotton fibers which is suitable to replace one of the three polypropylene layers of face mask type II in order to reduce non-biodegradable waste production and limit the negative impact of used masks on the environment. The work focused on the design of a nonwoven structure based on properly blending cotton and flax fibers as well as ensuring the cover factor, which can support the mask\'s barrier properties against air dust particles and does not make breathing difficult. Additionally, a biodegradable film was developed to connect the nonwoven layer with the other polypropylene filtering layers. The effectiveness of the biodeterioration of the flax/cotton nonwoven was evaluated based on a test of the susceptibility of materials to the action of soil microorganisms. The flax/cotton nonwoven layer was tested in terms of mechanical, physical, and biophysical properties, and an analysis of the covering of the nonwoven surface with fibers was conducted as well. The results confirmed that the structure of flax/cotton nonwovens is suitable to replace the nondegradable polypropylene layer of the face mask type II to improve its environmental performance.

Developing polymer-based organic afterglow materials with switchable ultralong organic phosphorescence (UOP) that are insensitive to moisture remains challenging. Herein, two organic luminogens, BBCC and BBCS, were synthesized by attaching 7H-benzo[c]carbazole (BBC) to benzophenone and diphenyl sulfone. These two emitters were employed as guest molecules and doped into epoxy polymers (EPs), which were constructed by in situ polymerization to achieve polymer materials BBCC-EP and BBCS-EP. It was found that BBCC-EP and BBCS-EP films exhibited significant photoactivated UOP properties. After light irradiation, they could produce a conspicuous organic afterglow with phosphorescence quantum yields and lifetimes up to 5.35% and 1.91 s, respectively. Meanwhile, BBCS-EP also presented photochromic characteristics. Upon thermal annealing, the UOP could be turned off, and the polymer films recovered to their pristine state, showing switchable organic afterglow. In addition, BBCC-EP and BBCS-EP displayed excellent water resistance and still produced obvious UOP after soaking in water for 4 weeks. Inspired by the unique photoactivated UOP and photochromic properties, BBCC and BBCS in the mixtures of diglycidyl ether of bisphenol A (DGEBA) and 1,3-propanediamine were employed as security inks for light-controlled multilevel anticounterfeiting. This work may provide helpful guidance for developing photostimuli-responsive polymer-based organic afterglow materials, especially those with stable UOP under ambient conditions.

Dehumidifying air via refrigerant cooling method consumes a tremendous amount of energy. Independent humidity control systems using desiccants have been introduced to improve energy efficiency. This research aimed to find an alternative to the commonly used solid desiccant, silica gel, which has weak physical adsorption properties. It also aimed to overcome the limitation of liquid desiccants that may affect indoor air quality and cause corrosion. This study reports on the synthesis of poly(vinyl alcohol-co-acrylic acid), P(VA-AA), through solution polymerisation by hydrolysing poly(vinyl acetate-co-acrylic acid), P(VAc-AA). This viable copolymer was then incorporated with graphene oxide (GO) at different concentrations (0 wt.%, 0.5 wt.%, 2 wt.% and 5 wt.%) to enhance the adsorption-desorption process. The samples were tested for their ability to adsorb moisture at different levels of relative humidity (RH) and their capability to maintain optimum sorption capacity over 10 repeated cycles. The nanocomposite film with 2% GO, P(VA-AA)/GO2, exhibited the highest moisture sorption capacity of 0.2449 g/g for 60-90% RH at 298.15 K, compared to its pristine copolymer, which could only adsorb 0.0150 g/g moisture. The nanocomposite desiccant demonstrated stable cycling stability and superior desorption in the temperature range of 318.15-338.15 K, with up to 88% moisture desorption.

Datura metel L. leaf extract mediated sodium alginate polymer membrane was successfully made using the solution casting technique. Electric, electrochemical, physicochemical and antimicrobial analyses of the prepared film were investigated. Functional groups of polysaccharides are identified in FTIR analysis and crystallinity/amorphous of the prepared samples was studied using XRD analysis. The prepared polymer membrane (DmMSA2) exhibits the ionic conductivity of 2.18 × 10-4 Scm-1, maximum specific capacitance of 131 F/g at a current density of 0.2 A/g and also exhibits a significant effect of antimicrobial activity against human pathogens. Hence, Datura metel L. leaf extract mediated polymer membranes are promising candidates for solid-electrolyte in supercapacitor devices and antimicrobial agents in food packaging applications.